Pioneer PRO-610HD, PRO-510HD Procedures, Prior to Adjustment, Confirmation of convergence data

Page 14

PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5

6CONVERGENCE ADJUSTMENT

1. Procedures

1.When replacinf the DIGITAL CONV. Assy, replace the EEPROM of new DIGITAL CONV. Assy with the EEPROM of old DIGITAL CONV. Assy.

2.Check the initial data for the convergence adjustment.

3.Perform the coarse adjustment for the green to roughly correct distortion of the green.

4.Fine-adjust the green to eliminate any distortion. The green becomes the standard for the red and the blue.

If necessary, repeat steps 3 and 4. Green adjustment is completed.

5.Perform the coarse adjustment for the red by roughly converging the red with the green.

6.Fine-adjust the red until the red is completely converging with the green.

If necessary, repeat steps 5 and 6. Red adjustment is completed.

7.Perform the coarse adjustment for the blue by roughly converging the blue with the green.

8.Fine-adjust the blue until the blue is completely converging with the green.

If necessary, repeat steps 7 and 8. Blue adjustment is completed.

9.Display the green, red, and blue colors at the same time to check the convergence. Readjust the convergence if necessary.

2. Prior to Adjustment

There are five screen modes, and convergence adjustment is required for each mode. For adjustment, input the following video signal:

Table 1 Input signal

Screen mode

Input signal

1. FULL (FULL, 4:3 NORMAL)

 

2. ZOOM (ZOOM)

NTSC (480i) signal

3 CINEMA (CINEMA WIDE)

 

4. NATURAL (NATURAL WIDE)

 

5. FULL for HD (HD/DTV)

HD/DTV (1080i) signal

NTSC : Stable signal source, such as an SG or an LD/DVD player

HD : Stable signal source, such as an HD SG or a DTV tuner (SH- D09, etc.) Only PRO-610HD5/510HD5 can use the SH-D09.

The data stored in the EEPROMs are as follows: IC1410

OFFSET CONVER. MODE 1 (DFH, DFV) OFFSET CONVER. MODE 3 Factory-preset values for convergence

User-adjusted values for convergence (CENTER, MULTI-POINT)

IC1656

OFFSET CONVER. MODE 1 (HDP)

OFFSET CONVER. MODE 2

3.2 Confirmation of convergence data

The convergence coarse adjustment modes change cyclically, as shown below, with each press of the DOT key in FACTORY mode:

Convergence coarse adjustment

DOT key (pressed once)

: OFFSET CONVER. MODE 1

 

 

 

DOT key (pressed twice)

: OFFSET CONVER. MODE 2

DOT key (pressed three times) : OFFSET CONVER. MODE 3

Cyclical change

Check whether the data of MODE 1 and MODE 2 are as shown in Table 2.

The cross-hatch signal is generated inside the unit, and is auto- matically displayed in OFFSET CONVER. mode and MANUAL CONVERGENCE mode. You can turn on and off the cross-hatch signal with the YELLOW key.

Screen indication

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

DFH

 

 

0F0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When CRTs are replaced or when the deflection yoke is moved, perform the deflection yoke adjustment, horizontal and vertical size adjustments, and centering magnet adjustments before the convergence adjustment. (See Pages 201, 204 and 205)

3. Convergence Adjustment

3.1Replacement of the EEPROMs inside the DIGITAL CONV. Assy

IC1410 24LC128P

IC1656 24LC08B (I) P

DIGITAL CONV. ASSY

Shield Case

IC1410

IC1656

A

A

 

B

C

 

 

 

 

Screen mode:

 

 

 

F

: FULL

Z

: ZOOM

C : CINEMA

N

: NATURAL

H

: FULL for HD

 

The Screen modes change cyclically with each press of the SCREEN mode key.

B

Adjustment items can be selected with the numeric keys. See Table 2.

C

Adjustment data:

MAX 1FF 100 001

CNT 000 3FF 2FF

MIN 200

Data can be adjusted with the VOL+ and VOL- keys.

206

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PRO-610HD PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Main Contents of Memory Name of AssyAssembly Adjustment Location Adjustment ItemsAssembly Adjustment Location Guide If Mirror and ScreenPosition Switch withFront panel PressControl Unit Other Offset modeKeys on the Remote Telop Blue Brightness AdjustmentInput signal Black Burst Input Deflection Yoke Adjustment 1Deflection Yoke Lean Adjustment 2Screen Center AdjustmentFocus VR VR1 Focus Adjustment 1Focus Adjustment of Lens Assy2Focus VR Adjustment Focus VRDigital Conv Assy Menu → Setup → Convergence → FullTest-cross Position Check 2Vertical Size Adjustment Screen Size Adjustment1Size Mode Size modeReference 3Horizontal Size AdjustmentAbout H. Phase PRO-610HD SD-582HD5 PRO-510HD SD-532HD5Convergence coarse adjustment ProceduresPrior to Adjustment Screen mode Input signalOffset Conver Data Coarse Adjustment of the GreenWaveforms adjustable in the coarse adjustment of the green Numeric KeyCoordinates where the cursor adjustment point is located Fine-adjustment of the GreenPattern for each adjustment item Key No. `Adjustment Technique 1st step Color to be adjusted4th step Coarse Adjustment of the Red2nd step 3rd stepFine-adjustment of the Red RV BVWhite Balance Adjustment 1Contrast Adjustment Coarse Adjustment and Fine Adjust- ment of the BlueConfirmation of Adjustment RGB STD Offset Compornent 31, 33KCompornent 15K DRV-R3Color/Tint Adjustment Adjustment Procedure of White BalnceColor Temp B&W for STD Blue cyclicallyColor Temp Film for STD Green cyclically Color Temp News for STDGND Panel AdjustmentProcedures Panel Adjustment for DTV PRO-610HD, PRO-510HD only Size Adjustment of the Panel Part of the 43 Normal Screen218 YES How to diagnose a failureDiagnosis Method CONV. AMP AssyStatus Causes Check Items Probable Defective Parts Causes Check Items Probable Defective Parts AWV1800 Elite AWV1799 Elite Block Diagram of the Protection CircuitD915 D321 D923Disassembly How to remove the screen for adjusting Lens assembliesDisconnect the Anode Cable FBTWiring Diagram FBT Focus WireRear Section Video A/D Converter ∙ Block Diagram ∙ List of IC∙ Pin Function Pin Name Pin FunctionConverter ∙ Block Diagram Vccd ClkgClkb CompTtlgnd SenableIovcc IogndSystem Controller IC ∙ Pin Function Mras MclkcMCS Mcas235 236 Vclk HBLK1 CLP1CLP2 HBLK2EM636327Q-8 SUB Video Service Assy IC3601, IC3604 PRO-610HD, PRO-510HD onlySystem micro-computer IC ∙ Pin Function Pin Name Pin FunctionSAA4990H SUB Video Assy IC3401 SD-582HD5, SD-532HD5 only 2M9 Field Memory IC ∙ Pin Function SAA4977H-K SUB Video Assy IC3403 SD-582HD5, SD-532HD5 only Besic A/D, D/A Memory Control IC ∙ Pin FunctionPin Function 24LC128IP Digital CONV. Assy IC141024LC08BIP Digital CONV. Assy IC1656 8Kbit Cmos Serial Eeprom Pin Assignment Top viewCM0006CF Digital CONV. Assy IC1401 Digital Convergence Correction IC ∙ Pin FunctionRvout BvoutGvout BhoutVideo Filter IC Pin Assignment Top view 24LC32AIP Signal Assy IC2454ML6420CS-3 Signal Assy IC7501 GndbCXA2094Q Signal Assy IC2701 US Audio Multi-channel Decoder IC ∙ Block DiagramAUX1-L SuboutAUX1-R AUX2-LCM0010AF Signal Assy IC7703 D Inputs for Sub Video SignalsImage D/A output Main PLLSub PLL Digital Input DramI2C Bus TestSUB Video Assy IC3002 TK15420M Signal Assy IC7102, IC7302, IC7502MC33167TV Power Supply Assy IC204 Connecting VIDEO/AUDION Equipment ExplanationTo Watch TV To turn off the soundProgram Block V. Chip Function Mpaa RatingSetting the Program Blocking Level Mpaa Rating HOW to Remove Blocking from a Program in Progress Changing PasswordViewing TWO Screens Split screen MULTI-SCREEN FunctionPress the Search button Press Menu and select SET UP by Adjust the blue line Changing Screen Mode Picture AdjustmentsSound Adjustments Special Notes265 Panel Facilities and Specifications Volume buttons TV Power button STANDBY/ON = CH Enter button Input DPO OFF Input Selector buttons TV, Input 1 to Input 273 Display and amplifier section Monitor
Related manuals
Manual 92 pages 6.09 Kb

PRO-510HD, PRO-610HD specifications

The Pioneer PRO-510HD and PRO-610HD are two advanced professional display monitors that exemplify cutting-edge technology in the realm of high-definition visual solutions. Designed for various applications, including broadcasting, live events, and video production, these monitors provide exceptional image quality and versatile features.

One of the standout characteristics of both models is their high-resolution display capabilities. The PRO-510HD boasts a 51-inch screen size with an impressive resolution of 1920 x 1080 pixels, ensuring sharp and vibrant images that meet the demands of professional users. The larger PRO-610HD features a 61-inch screen size with the same high-definition resolution, allowing for an immersive viewing experience.

These monitors leverage advanced LCD technology to deliver remarkable color accuracy and consistent brightness. With a wide color gamut, users can expect true-to-life colors, making these monitors ideal for color-critical applications. The brightness levels of both models reach up to 700 cd/m², ensuring visibility even in brightly lit environments.

Connectivity is a crucial aspect of any professional monitor, and the PRO-510HD and PRO-610HD are equipped with a range of input options. They offer multiple HD-SDI, HDMI, DVI, and analog connections, allowing for seamless integration with various broadcasting and production equipment. This flexibility ensures that users can easily connect their devices without the need for additional converters or adapters.

Another significant feature of these monitors is the built-in waveform and vector scope displays. These tools are essential for ensuring proper exposure and color balance, providing users with real-time monitoring of their video signals. The monitors also support various aspect ratios, making it easy to adjust the display according to specific project requirements.

Durability is key for professional equipment, and both the PRO-510HD and PRO-610HD are constructed with robust materials, ensuring longevity even in demanding environments. The monitors are designed for continuous operation, making them reliable for long hours of use whether in studios or on location.

In conclusion, the Pioneer PRO-510HD and PRO-610HD are powerful tools for professionals who require high-quality displays with advanced features. Their excellent image quality, extensive connectivity options, and integrated monitoring tools make them an attractive choice for anyone involved in video production or broadcasting. With their durable design and user-friendly operation, these monitors stand out as reliable partners in the visual media landscape.
Top Page Image Contents