Pioneer PRO-610HD Special Notes, Picture Adjustments, Sound Adjustments, Changing Screen Mode

Page 72

PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5

SPECIAL NOTES

Picture Adjustments

MOVIE or GAME mode may not be selected when receiving RGB input.

GAME mode setting:

∙All signals output from the Projection Monitor will be unaffected. Only the original output signal is sent through the output jacks.

Picture Quality setting:

•The COLOR, TINT, and SHARP settings may not be changed when receiving RGB input.

•When DPO is on, CONTRAST, BLACK LEVEL and COLOR cannot be adjusted.

•When picture quality has been adjusted, the user mode data will be overwritten with the new settings.

Other Picture Quality setting:

Only the COLOR TEMP settings may be changed when receiving RGB input.

PURECINEMA adjustment:

Normally, this function should be set to “HQ” (High Quality), however, occasionally this setting may cause slight syncopation problems with the audio track. If you are bothered by this, select “STD” (Standard) or “OFF”. If “OFF” is selected, normal progressive signal processing is performed.

Sound Adjustments

BASS, TREBLE and BALANCE are SPEAKER mode settings, which can only be adjusted when mode is NORMAL.

Surround Mode setting:

•This function cannot be used when the SPEAKER mode is CENTER IN or when the SPEAKER mode is OFF and AUDIO OUT mode is FIXED.

•The surround effect cannot be obtained with mono sound.

•In some cases, the surround effect may be minimal.

Changing Screen Mode

∙When 1080i or 480p component signals or RGB signals are input, SCREEN MODE will be limited to FULL.

Connection with Receiver (1)

Speaker and AUDIO OUT Setting:

•After the speaker mode is set to CENTER IN, the volume of the center speaker should be controlled from this monitor.

•If AUDIO OUT is set to VAR and the sound is distorted, lower the Monitor volume.

Connection with Receiver (2)

SYSTEM MODE ON :

∙The input cannot be switched even if you press the Input selector button of the remote control unit.

∙On the sub-picture of a SPLIT screen, only the input signal from the antenna can be displayed.

∙The SEARCH screen function will not be operable.

∙No signal will be output from the AUDIO OUTPUT terminal.

∙Setting SYSTEM MODE ON will cause RGB input signals to not be displayed.

264

Image 72

Contents PRO-610HD PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Main Contents of Memory Name of AssyAssembly Adjustment Location Adjustment ItemsAssembly Adjustment Location Guide If Mirror and ScreenSwitch with Front panelPosition PressOther Offset mode Keys on the RemoteControl Unit Brightness Adjustment Input signal Black Burst InputTelop Blue Deflection Yoke Adjustment 1Deflection Yoke Lean Adjustment 2Screen Center AdjustmentFocus Adjustment 1Focus Adjustment of Lens Assy 2Focus VR AdjustmentFocus VR VR1 Focus VRMenu → Setup → Convergence → Full Test-cross Position CheckDigital Conv Assy Screen Size Adjustment 1Size Mode2Vertical Size Adjustment Size mode3Horizontal Size Adjustment About H. PhaseReference PRO-610HD SD-582HD5 PRO-510HD SD-532HD5Procedures Prior to AdjustmentConvergence coarse adjustment Screen mode Input signalCoarse Adjustment of the Green Waveforms adjustable in the coarse adjustment of the greenOffset Conver Data Numeric KeyFine-adjustment of the Green Pattern for each adjustment itemCoordinates where the cursor adjustment point is located Key No. `Adjustment Technique 1st step Color to be adjustedCoarse Adjustment of the Red 2nd step4th step 3rd stepFine-adjustment of the Red RV BVCoarse Adjustment and Fine Adjust- ment of the Blue Confirmation of AdjustmentWhite Balance Adjustment 1Contrast Adjustment STD Offset Compornent 31, 33K Compornent 15KRGB DRV-R3Color/Tint Adjustment Adjustment Procedure of White BalnceBlue cyclically Color Temp Film for STDColor Temp B&W for STD Green cyclically Color Temp News for STDPanel Adjustment ProceduresGND Panel Adjustment for DTV PRO-610HD, PRO-510HD only Size Adjustment of the Panel Part of the 43 Normal Screen218 How to diagnose a failure Diagnosis MethodYES CONV. AMP AssyStatus Causes Check Items Probable Defective Parts Causes Check Items Probable Defective Parts Block Diagram of the Protection Circuit D915AWV1800 Elite AWV1799 Elite D321 D923Disassembly How to remove the screen for adjusting Lens assembliesDisconnect the Anode Cable FBTWiring Diagram FBT Focus WireRear Section Video A/D Converter ∙ Block Diagram ∙ List of IC∙ Pin Function Pin Name Pin FunctionConverter ∙ Block Diagram Clkg ClkbVccd CompSenable IovccTtlgnd IogndSystem Controller IC ∙ Pin Function Mclkc MCSMras Mcas235 236 Vclk CLP1 CLP2HBLK1 HBLK2EM636327Q-8 SUB Video Service Assy IC3601, IC3604 PRO-610HD, PRO-510HD onlySystem micro-computer IC ∙ Pin Function Pin Name Pin FunctionSAA4990H SUB Video Assy IC3401 SD-582HD5, SD-532HD5 only 2M9 Field Memory IC ∙ Pin Function SAA4977H-K SUB Video Assy IC3403 SD-582HD5, SD-532HD5 only Besic A/D, D/A Memory Control IC ∙ Pin Function24LC128IP Digital CONV. Assy IC1410 24LC08BIP Digital CONV. Assy IC1656Pin Function 8Kbit Cmos Serial Eeprom Pin Assignment Top viewCM0006CF Digital CONV. Assy IC1401 Digital Convergence Correction IC ∙ Pin FunctionBvout GvoutRvout Bhout24LC32AIP Signal Assy IC2454 ML6420CS-3 Signal Assy IC7501Video Filter IC Pin Assignment Top view GndbCXA2094Q Signal Assy IC2701 US Audio Multi-channel Decoder IC ∙ Block DiagramSubout AUX1-RAUX1-L AUX2-LCM0010AF Signal Assy IC7703 D Inputs for Sub Video SignalsMain PLL Sub PLLImage D/A output Dram I2C BusDigital Input TestTK15420M Signal Assy IC7102, IC7302, IC7502 MC33167TV Power Supply Assy IC204SUB Video Assy IC3002 Connecting VIDEO/AUDION Equipment ExplanationTo Watch TV To turn off the soundProgram Block V. Chip Function Mpaa RatingSetting the Program Blocking Level Mpaa Rating HOW to Remove Blocking from a Program in Progress Changing PasswordViewing TWO Screens Split screen MULTI-SCREEN Function Press the Search button Press Menu and select SET UP by Adjust the blue line Picture Adjustments Sound AdjustmentsChanging Screen Mode Special Notes265 Panel Facilities and Specifications Volume buttons TV Power button STANDBY/ON = CH Enter button Input DPO OFF Input Selector buttons TV, Input 1 to Input 273 Display and amplifier section Monitor

Related manuals

Manual 92 pages 6.09 Kb