Brother MFC/HL-P2000 manual Operating and Storage Environment, Power Supply

Page 13

USER’S GUIDE

OPERATING AND STORAGE ENVIRONMENT

Please take note of the following before using the machine.

Power Supply

Use the machine within the specified power range.

AC power: ±10% of the rated power voltage in your country

Frequency: 50/60 Hz (220 V– 240 V) or 50/60 Hz (110–120 V)

The power cord, including extensions, should not exceed 5 meters (16.5 feet).

Do not share the same power circuit with other high-power appliances, particularly an air conditioner, copier, shredder and so on. If it is unavoidable that you must use the machine with these appliances, it is recommended that you use an isolation transformer or a high-frequency noise filter.

Use a voltage regulator if the power source is not stable.

Environment

The machine should be installed near a power outlet which is easily accessible.

Use the machine only within the following ranges of temperature and humidity.

Ambient temperature: 10°C to 32.5°C (50°F to 90.5°F)

Ambient humidity:

20% to 80% (without condensation)

The machine should be used in a well ventilation room.

Place the machine on a flat, horizontal surface.

Keep the machine clean. Do not place the machine in a dusty place.

Do not place the machine where the ventilation hole of the machine can be blocked.

Do not place the machine where it is exposed to direct sunlight. Use a blind or a heavy curtain to protect the machine from direct sunlight when the machine is unavoidably set up near a window.

Do not place the machine near devices that contain magnets or generate magnetic fields.

1-6

Image 13

Contents MFC/HL-P2000 Please read this manual thoroughly before using the machineTable of Contents Copy Troubleshooting To Use the Machine Safely Definitions of Warnings, Cautions, and NotesShipment of the Machine For USA & Canada Only About the Guidebooks Finding Out How to Use the MachineMachine Overview About Your MachineHigh Resolution and Fast Printing Speed FeaturesVersatile Paper Handling CopierRemote Printer Console Program for DOS Twain Compliant Scanner DriverPopular Printer Emulation Support Sleep Mode Power Save Mode Environment-Friendly Economy Printing ModeEnhanced Memory Management Low Running CostOperating and Storage Environment Power SupplyEnvironment Introducction Paper Specifications Cut Sheet RemarksLabels / Transparencies Fan the Paper Straighten the Paper Special PaperEnvelopes EnvelopesPaper Capacity in Document Feeder Document SpecificationsMULTI-PURPOSE Sheet Feeder for Printing Opening the Feeder Loading Paper or Envelopes in the Feeder Loading Paper into the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Opening the Output Tray Extending the Extension Support Wire Output Tray and Paper Support WireReady Paper Lamp Lamps and SwitchData Toner Lamp Alarm LampDrum Lamp Other Control Features SwitchSleep Mode Alarm Test Print ModeDrum ReadyTo Make Settings for Each Copy Copying in Standard ModeEnlarge/Reduce Photo/TextEnlarge and Reduce Number of CopiesError Chapter Scan Software MFC-P2000 Scan Replacing the Toner Cartridge Chapter MaintenanceRemoving the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Turn the drum unit upside down gently Cleaning the Primary Corona Wire 11 Drum Unit Nearly at the End of its Life Replacing the Drum Unit12 Removing the Drum Unit 14 Removing the Toner Cartridge Do not remove the starter sheet17 Installing the Drum Unit Cleaning the Machine Exterior Cleaning the Machine20 Turning off the Switch and Unplugging Cleaning the Machine Interior and Drum UnitGently wipe the scanner window with a soft dry cloth See the section Replacing the Drum Unit in this chapter 24 Cleaning the Scanning Unit Cleaning the Scanning UnitRE-PACKING the Machine 25 Removing the Drum Unit Assembly26 Placing the Drum Unit in the Plastic Bag Alarm ↔ Alarm Indications AT a GlanceOperator Calls for the Printing Function Paper ↔Page Operator Calls for the Copying and Scanning Functions Drum Alarm Ready Data Service Calls for the Printing FunctionService Calls for the Copying and Scanning Functions Locating Paper Jam Position Paper JamsDo not pull the Jammed Paper from the Output Tray Paper Jam near the Drum Unit Paper Jam in the Document Feeder Setting Up the Machine for Windows Setting Up the Machine HardwarePower switch is on Question RecommendationQuestion Setting Up the Machine for DOSPaper Handling Printing Scan CopyTogether right now, over Print QualityToner scatters and stains the printed Machine Interior and Drum Unit Black spots appears on the printed paper at 94mm intervals Appendix Scanning CopyingElectrical and Mechanical FunctionsParallel Interface Specifications Fig. A-1 Parallel Interface Cable Bitmapped Fonts Resident FontsHP LaserJet IIP Mode Symbol SETS/CHARACTER SetsEpson Mode IBM ModeHP LaserJet IIP HP LaserJet IIP, Epson FX-850, IBM Propritner XL USER’S Guide Compilation and Publication Notice TrademarksIndustry Canada Compliance Statement For Canada Only RegulationsInternational Energy Star Compliance Statement Laser Safety For 110-120 V Model OnlyRadio Interference 220-240 V Model Only FDA Regulations For 110-120 V Model Only IEC 825 Specification For 220-240 V Model OnlyDeclaration of Conformity For Europe Atención Geräuschemission / Acoustic Noise Emission For Germany Only Important For Your SafetyImportant Wiring Information For U.K. only Index RPC