Brother 2300 manual Cutter

Page 68

Error Message	Cause	Remedy

CUTTER	This message appears if the tape cut-	Turn the P-touch off, then on
ERROR!	ter is closed when you try to print or	again.
	feed the tape.

EEPROM	This message appears if a checksum	Contact your service representa-
ERROR!	error occurred when the P-touch was	tive.
	turned on or if the keyword was dam-
	aged and it failed to initialize.

INTERFACE	This message appears if an error	Cancel the print job, and then
ERROR!	occurs while data is being sent from	try printing again.
	the computer to the P-touch.

INVAL.	This message appears if the cursor is	Move the cursor below a
CHRS!	not below a number when you hold	number before holding down
	down c and press O.	c and pressing O.

LENGTH	• This message appears if the text is	• Shorten the text to less than 3’
LIMIT!	longer than 3’ 3 1/3” (1 meter) when	3 1/3” (1 meter) before trying
	you try to print.	to print.
	• This message appears if the Length	• Set the label length between
	function is used to set a label	1.6” (4.0 cm) and 11.8” (30.0
	length that is less than 1.6” (4.0	cm).
	cm) or more than 11.8” (30.0 cm).
	• This message appears if the Tab	• Set the tab length so that it is
	Length function is used to set a tab	less than 11.8” (30.0 cm).
	length that is more than 11.8”
	(30.0 cm).

LINE	This message appears if the number	Reduce the number of lines or
LIMIT!	of lines in the text is greater than the	install a tape of greater width.
	maximum number of lines possible
	for the installed tape.

MEMORY	This message appears if you try to	Delete an unwanted ﬁle to make
FULL!	store a text ﬁle after 300 characters	room for the new one.
	have already been stored in the
	memory.

NO	This message appears if you try to	Store a text ﬁle ﬁrst.
FILES!	recall or delete a text ﬁle from the
	memory when none are stored.

64

Image 68

Contents 2300 Introduction Canadian Department of Communications Compliance StatementContents Page Getting Started General DescriptionGeneral Precautions Use eight AA alkaline batteries in this machine BatteriesTo change the batteries Optional AC Adaptor To connect the optional AC adaptorTape Cassette To change the tape cassetteConnecting the P-TOUCH to a Computer To connect the P-touch to the computerInstalling P-TOUCH Editor To install the P-touch Editor softwareHard disk free space At least 20 MB Available memory Minimum 32 MBPage For a Custom installation To install the USB printer driver Page To replace, add or delete the printer driver Page For a basic installation On a Macintosh ComputerFor a Custom installation Starting P-TOUCH Editor To select the PT-2300/2310 as the printerTo delete P-touch Editor Version 3.1 and the printer driver To start up P-touch EditorTitle bar Attaching Labels BarcodesDatabases Laminated TapeNON-LAMINATED Tape INSTANT-LETTERING Tape RUB-ON TransfersIRON-ON Transfer Tape Fabric Tape WashingDrying IroningStamp Tape To clean the print head and rollersPrint Head & Rollers Left Cursor KEY Power KEYCursor Keys CODE, ALT & Shift Keys Right Cursor KEYUP Cursor KEY Down Cursor KEYTo type To start the Symbol functionALT KEY To type in many capital letters Shift KEYTo type in % To add a space Space KEYReturn KEY TAB Function Tape widths Maximum number of lines that can be printedTo add a new line To select an item from a listTo set the tab length to To set the tab lengthTo add a tab Delete KEY To delete one characterLine OUT Function Clear Function To clear the text and formatsTo delete just the text To clear just the textTo type in an accented character Accent FunctionLetters Accented characters Symbol Function C E N TTo add the symbol Group SymbolTo type in a symbol Auto Format Function To make a stamp To select a preset formatStamp Function To cut a stamp To afﬁx a stampFold over Font Function To change the font settingTo select the Font 2 font setting Tape widths Sizes in points Width setting Width setting WideSize & Width Functions To change the size setting To select the 24 point size settingTo change the width setting To select the Wide width settingTo change the style setting Style FunctionTo select the I+SHAD style setting Font Style setting SettingTo turn on or off the Underline function Font Setting Style settingUnderline Function Frame Function To select the Undl on underline settingTo change the frame setting To select the candy frame setting Tape Margin FunctionHorizontal Alignment Function To change the tape margin settingTo select the Half tape margin setting To change the horizontal alignment setting Mirror Printing FunctionLength Function To turn on or off the mirror printing settingTo select the on mirror printing setting To turn on or off the Length function To select a label lengthAuto CUT Function To turn on the Auto cut functionPrint KEY Feed & CUT FunctionTo print a label To feed and cut off 1 24 mm of tapeTo print three labels with numbers 1, 2 Numbering FunctionTo use the Numbering function Repeat Printing Function To use the Repeat printing functionTo print three copies of a label Memory Functions Storing TextTo store a text file To overwrite the stored file with the new oneRecalling Text Deleting a FileTo recall a text file To delete a text fileTo store text under ﬁle number To recall the text from ﬁle numberTo delete the text stored under ﬁle number Troubleshooting Problem RemedyError Message List Cause RemedyCutter Tape Software SpecificationsHardware Stock No Description AccessoriesSupplies 12mm-wide laminated tapes QTY SH-MB Accessory Order Form Stock No Description Price Quantity TotalAccessory Order Form LA6059001