Additional Washer Security

Installation

(Coin Models Only)

Located on the service door of the washer is a flat Phillips head screw. During shipment, this screw is used to attach the service door to the meter case. For additional security, this screw can be reinstalled inside the control hood of your washer. Refer to instructions below for installation.

Tamper-resistant screws also can be installed for additional security. Tamper-resistant screws, bits and bit holder are available as optional equipment at extra cost. Part numbers are:

•Bit (No. 8 screws) Part No. 281P4

•Bit (No. 12 screws) Part No. 282P4

•Bit Holder (3/8 drive) Part No. 24161

•Control panel tamper-resistant screw Part No. 35528

•Front panel tamper-resistant screw Part No. 35527

The following list is the procedure required to install the Phillips head screw and tamper-resistant screws:

WARNING

Any disassembly requiring the use of tools must be performed by a suitably qualified service person.

W299

To reduce the risk of electric shock, fire, explosion, serious injury or death:

•Disconnect electric power to the washer before servicing.

•Never start the washer with any guards/ panels removed.

•Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded.

W003

1.Remove the Phillips head screw from service door (refer to Figure 14).

2.Remove two screws holding control panel to control hood.

3.Tilt control panel forward and lay on a protective pad to prevent scratching of cabinet top.

4.Insert Phillips head screw down through double “D” hole in left rear corner of cabinet top (inside control hood) until it engages retainer nut located on left rear corner gusset of cabinet.

5.Finger tighten screw.

IMPORTANT: Do not use a power driver to tighten screw. Torque of a power driver could over-tighten screw causing damage to cabinet assembly.

6.Secure control panel to control hood using two No. 8 tamper-resistant screws, Part No. 35528.

7.Remove two screws holding front panel to base of washer and install two No. 12 tamper-resistant screws, Part No. 35527.

TLW2102N

135528 No. 8 Screws

2Double “D” Hole

335527 No. 12 Screws

Figure 14

202068

TLW12CTLW12C specifications

Alliance Laundry Systems TLW12CTLW12C is a highly efficient and robust washer-extractor that exemplifies modern engineering in commercial laundry equipment. Designed primarily for high-demand settings such as laundromats, hotels, and large institutions, this model stands out due to its advanced features and exceptional performance.

One of the prominent features of the TLW12CTLW12C is its large capacity, allowing users to process significant loads of laundry in a single cycle. With a drum that can accommodate up to 12 kilograms of laundry, this washer-extractor ensures fewer loads and enhanced productivity, which can greatly benefit businesses aiming to optimize their operations.

The TLW12CTLW12C is equipped with a powerful motor that delivers high extraction speeds, leading to reduced moisture content in the laundry after each cycle. This efficiency translates into shorter drying times, ultimately conserving energy and reducing operational costs. The machine's design also features a robust suspension system that minimizes vibrations, ensuring quiet and stable operation even at full load.

In terms of technology and user control, the TLW12CTLW12C boasts a user-friendly digital control interface, allowing operators to easily select from a wide range of programmable wash cycles tailored for various fabrics and soil levels. This versatility is essential for achieving optimal cleaning results across different textile types, from delicate items to heavily soiled linens.

Another significant characteristic of the TLW12CTLW12C is its energy efficiency. This model is designed with advanced water and energy-saving technologies that not only reduce consumption but also promote environmentally-friendly practices. Additionally, it features automatic water level control and temperature regulation, ensuring consistent wash quality while further minimizing resource usage.

Durability is a pivotal feature of the TLW12CTLW12C, which is constructed from high-quality materials intended to withstand the rigors of commercial usage. The stainless-steel drum and outer construction are resistant to rust and corrosion, ensuring a long lifespan with minimal maintenance.

Overall, the Alliance Laundry Systems TLW12CTLW12C is designed to meet the demanding needs of commercial laundry operations with its blend of capacity, efficiency, flexibility, and durability. Its innovative features make it a worthy investment for those seeking reliable performance in laundry management.