Low Standpipe Installation

Installation

If the drain facility is lower than the cabinet top, a siphon break kit, Part No. 562P3, must be installed in the drain hose to prevent siphoning action and drain hose MUST be cut to fit the washer installation. Refer to Figure 8. Use one No. 25863 Hose Coupling to splice hose. The No. 562P3 Siphon Break Kit and No. 25863 Hose Coupling are available as optional equipment at extra cost through an authorized dealer or parts distributor. Installation instructions are supplied with the kit.

OPTIONAL: Raise the standpipe to the recommended height of 36 inches (91.44 cm).

IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/2 inch (3.8 cm) outside diameter drain hose.

1 2

{

W295I

1Drain Hose Elbow

2562P3 Siphon Break Kit

3Standpipe

4Cut Hose in This Area and Install No. 25863 Hose Coupling

525863 Hose Coupling

Figure 8

Step 5: Position and Level the Washer

Position washer so it has sufficient clearance for installation and servicing.

Place washer in position on a clean, dry, and reasonably firm floor. Installing the washer on any type of carpeting is not recommended.

Place rubber cups on all four leveling legs.

Place a level on the cabinet top and check if the washer is level from side to side and front to back.

If washer is not level, tilt washer back to access the front leveling legs. Loosen the locknuts and adjust legs by screwing into or out of washer base.

Once adjusted, tilt the washer forward on front legs and lower back down into position to set the rear self- leveling legs.

Washer must not rock. After washer is at desired height, tighten locknuts securely against bottom of washer base. If these locknuts are not tight, washer will not remain stationary during operation.

Improper installation or flexing of weak floor will cause excessive vibration.

Do not slide washer across floor once the leveling legs have been extended, as legs and base could become damaged.

NOTE: For areas with uneven floors, a No. 566P3 Adjustable Rear Leg Extension Kit is available as optional equipment at extra cost.

Verify that unit does not rock.

			3
6	5	4	TLW2100N

TLW2100N

1Washer Base

2Locknut

3Leveling Leg

4Rubber Cup

51/2 inch (12.7 mm) Clearance Between Washers

6Level

Figure 9

202068

TLW12CTLW12C specifications

Alliance Laundry Systems TLW12CTLW12C is a highly efficient and robust washer-extractor that exemplifies modern engineering in commercial laundry equipment. Designed primarily for high-demand settings such as laundromats, hotels, and large institutions, this model stands out due to its advanced features and exceptional performance.

One of the prominent features of the TLW12CTLW12C is its large capacity, allowing users to process significant loads of laundry in a single cycle. With a drum that can accommodate up to 12 kilograms of laundry, this washer-extractor ensures fewer loads and enhanced productivity, which can greatly benefit businesses aiming to optimize their operations.

The TLW12CTLW12C is equipped with a powerful motor that delivers high extraction speeds, leading to reduced moisture content in the laundry after each cycle. This efficiency translates into shorter drying times, ultimately conserving energy and reducing operational costs. The machine's design also features a robust suspension system that minimizes vibrations, ensuring quiet and stable operation even at full load.

In terms of technology and user control, the TLW12CTLW12C boasts a user-friendly digital control interface, allowing operators to easily select from a wide range of programmable wash cycles tailored for various fabrics and soil levels. This versatility is essential for achieving optimal cleaning results across different textile types, from delicate items to heavily soiled linens.

Another significant characteristic of the TLW12CTLW12C is its energy efficiency. This model is designed with advanced water and energy-saving technologies that not only reduce consumption but also promote environmentally-friendly practices. Additionally, it features automatic water level control and temperature regulation, ensuring consistent wash quality while further minimizing resource usage.

Durability is a pivotal feature of the TLW12CTLW12C, which is constructed from high-quality materials intended to withstand the rigors of commercial usage. The stainless-steel drum and outer construction are resistant to rust and corrosion, ensuring a long lifespan with minimal maintenance.

Overall, the Alliance Laundry Systems TLW12CTLW12C is designed to meet the demanding needs of commercial laundry operations with its blend of capacity, efficiency, flexibility, and durability. Its innovative features make it a worthy investment for those seeking reliable performance in laundry management.