GateWay Fax Systems 90SI manual 2 L-3 Omni / OMNIxi, Code Setting

Page 13

GateWay Fax Systems, inc.

Model 90si Secure Fax Gateway User's Guide

2.6.2L-3 OMNI / OMNIxi

Objective: To set the Secure Data mode to PSTN, Async, 9600 bps.

Apply power to the omni and login as an Authorized User <AU> or Terminal Administrator <TA>...

Press

Display

(logon)

LOGON SUCCESSFUL

ENTER

 

MENU

<TA MENU> / 0-EXIT TA MODE / 1-ZEROIZE

2, ENTER

<OMNI CONFIG> / 1-TERM CONTROL / 2-SET NETWORK

2, ENTER

(Example) NET: PSTN-SYNC / 1-PSTN ASYNC / 2-PSTN-SYNC

1

NET: PSTN-ASYNC

ENTER

 

BACK

<OMNI CONFIG> / 1-TERM CONTROL / 2-SET NETWORK

6, ENTER

(Example) Async 19200 bps

3, ENTER

Async 9600 bps

MENU

(to exit)

If your OMNI / 90si does not work after you make the above changes, confirm the following setting. To view these settings press the Menu button followed by each individual code digit followed by Enter. For example, 2,1 would be Menu, 2, Enter, 1, Enter to view the Term Control setting.

Code

Setting

Code

2,1

Term Control = Local

2,14

2,2

Set Network = PSTN ASYNC

3,1

2,4

Set LCL Port = EIA232

3,2,1

2,6

Set Rate = ASYNC 9.6 kbps

3,2,4

2,7,1-4

CLK Polarity = (set all to Normal)

3,3,1

2,12

DTE TX CLK = OMNI

3,3,4

2,13

RESYNC INTRVL = DSBL

 

Setting

Signaling = STANDARD

SEC Settings/Secure Mode = Traditional

SEC/SACS Voice/Secure Voice = ENBL

SEC/SACS Voice/ACL SEC Voice = DSBL

SEC/SACS Data/Secure Data = ENBL

SEC/SACS Data/ACL SEC Data = DSBL

Required L-3 provided LDI Red Data Cable: Each OMNI ships with a Local Data Cable, L-3 part number K10048260-4. One end of this cable terminates in a DB25 connector (into which the 90si plugs), the other con- nects to the "Local Data" connector on the back of the OMNI/OMNIxi.

www.gwfs.com, 877-951-9800, info@gwfs.com

help line: 877-951-9814

page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model 90si Step Procedure Connecting the Cots fax, 90si and Crypto90si Quick Reference Guide Transmitting a Secure FaxTable of Contents Introduction Getting StartedWhat in the Box TEL Line Connector Reset ButtonLooking at your 90si Memory Issues InstallationChoosing a Cots Fax Choose a Location3 Configuration Selection Chart Dual Mode ConsiderationsSecure Only Configuration Recommended Configuration Secure Non-Secure Description Operation 4 1-Line, Dual-Mode5 2-Line Dual-Mode 6 1-Line Dual-Mode with 910 Option Setting Your Chosen ConfigurationResponse Print the Default Settings List1 L-3 Secure Terminal Equipment STE Setting Up Your Encryption DevicePress Display 2 L-3 Omni / OMNIxi Code SettingGeneral Dynamics Viper General Dynamics SecteraMotorola STU-IIB & STU-IIIA While Off-Hook and in Clear mode Press DisplayWhile On-Hook Press Display Applying Power Using your 90siSending a Secure Fax Sending a Public Fax Dual-Mode Configurations OnlyCommunication Errors Power-upSystem Errors Receiving a Public Fax Dual-Mode Configurations OnlyScip Async Protocol Selecting a Transmit ProtocolMIL-STD-161 Protocols Synchronous Ricoh/Compat Protocols Synchronous Setting and Using the Default Transmit ProtocolProcedure Response Using a One-Time Transmit Protocol CodeOne-Time Transmit Protocol Troubleshooting Tips If Theres a problemHow Will You Know When All Else Fails...Call Our Help Line Warranty InformationSpecifications General SpecificationsDigital Interface Specifications Important Safety Instructions Safety Information and FCC RequirementsRelated Web Links Pin # DescriptionConsumer Information and FCC Requirements Help line Glossary Primary Secure Fax Secondary Fax Secure Data ModePrimary Non-Secure Fax ProtocolSynchronous STE Secure Terminal EquipmentTwo-Line Dual-Mode Configuration VoIP
Top Page Image Contents