Linksys PAP2-NA manual Placement Options, Stand Option, Wall-Mount Option

Page 11

Phone Adapter with 2 Ports for Voice-over-IP

Placement Options

There are three ways to place the Phone Adapter. The first way is to place the Phone Adapter horizontally on a surface. The second way is to stand the Phone Adapter vertically on a surface. The third way is to mount the Phone Adapter on a wall. The second and third options are explained in further detail below.

Stand Option

1.Remove the plate from the Phone Adapter’s bottom panel.

2.Line up the pegs of the Phone Adapter’s base with the mounting holes of the Phone Adapter’s bottom panel.

3.Insert the Phone Adapter’s base into the Phone Adapter’s bottom panel. Push the base in until it fits snugly.

4.Place the Phone Adapter in an appropriate location.

Congratulations! The installation of the Phone Adapter is complete.

If you need to change any of the Phone Adapter’s network settings, proceed to “Chapter 4: Using the

Phone Adapter’s Interactive Voice Response Menu.”

Wall-Mount Option

The Phone Adapter has two wall-mount slots on its back panel. The distance between the two slots is 58 mm (2.28 inches).

1.Determine where you want to mount the Phone Adapter.

2.Drill two holes into the wall. Make sure the holes are 58 mm (2.28 inches) apart.

3.Insert a screw into each hole, and leave 5 mm (0.2 inches) of its head exposed.

4.Maneuver the Phone Adapter so the wall-mount slots line up with the two screws.

5.Place the wall-mount slots over the screws and slide the Phone Adapter down until the screws fit snugly into the wall-mount slots.

Congratulations! The installation of the Phone Adapter is complete.

If you need to change any of the Phone Adapter’s network settings, proceed to “Chapter 4: Using the

Phone Adapter’s Interactive Voice Response Menu.”

Chapter 3: Connecting the Phone Adapter

Figure 3-5: Attaching the Phone Adapter’s Base

Figure 3-6: Phone Adapter Standing on Base

Figure 3-7: Measurement between Wall-Mount Slots

7

Placement Options

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Phone Adapter Copyright and Trademarks How to Use this GuideTable of Contents Front Panel Back PanelWhat’s in this Guide? IntroductionWelcome Introduction What’s in this Guide? Back Panel Ports Getting to Know the Phone AdapterFront Panel LEDs Router Phone Adapter Connecting the Phone AdapterInstructions for Connecting the Phone Adapter OverviewConnect the Ethernet Network Cable Remove the plate from the Phone Adapter’s bottom panel Placement OptionsStand Option Wall-Mount OptionUsing the Interactive Voice Response Menu Using the Phone Adapter’s Interactive Voice Response MenuAccessing the Interactive Voice Response Menu Interactive Voice Response Menu Has been enabled or disabled. If121 Enter the network 7932 Enter 1 to enable This feature is protected by a Configuring the Settings for Your Internet Phone Service Entering a PasswordCommon Problems and Solutions Appendix a TroubleshootingIP address Phone Adapter Internet phone 69 to Application Start and End Protocol IP Address EnableInternet phone 5060 to IP address Phone Adapter Internet phone 53 toIP address Phone Adapter Internet phone 69 to IP address Phone Adapter Internet phone 69 to Ethernet LED does not light up Frequently Asked QuestionsNetwork Neighborhood/My Network Places Appendix B Windows HelpShared Resources Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications 10~90% Non-Condensing Storage TempOperating Humidity Storage HumidityLimited Warranty Appendix E Warranty InformationThis product complies with Canadian ICES-003 Appendix F Regulatory InformationLinksys Appendix G Contact Information
Related manuals
Manual 33 pages 13.27 Kb
Top Page Image Contents