Linksys PAP2-NA manual IP address Phone Adapter

Page 19

Phone Adapter with 2 Ports for Voice-over-IP

4.Wait two minutes, and then power on your cable or DSL modem by plugging its power adapter into an electrical outlet.

5.Wait two minutes, and then power on the router by plugging its power adapter into an electrical outlet.

6.Wait five minutes, and then power on the Phone Adapter by plugging its power adapter into an electrical outlet.

7.Reboot one of your networked computers, and check to see if you have an active Internet connection.

8.Pick up the telephone. You should now have a dial tone.

•Set up port forwarding on your router. You must specify that four port ranges be forwarded to the IP address of the Phone Adapter. These four port ranges are as follows: 5060-5061 (UDP), 53-53 (UDP), 69-69 (UDP), and 10000-20000 (UDP).

Before you set up port forwarding on your router, change two of the Phone Adapter’s settings using its Interactive Voice Response Menu. First, disable its DHCP feature, and then assign a static IP address to the Phone Adapter. Refer to “Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu” for instructions.

If you have a non-Linksys router, refer to its documentation for instructions. If you have a Linksys router, then follow these instructions:

1.On one of your networked computers, open your web browser.

2.Access the Router’s Web-based Utility by going to http://192.168.1.1 or the IP address of the Router.

3.A login screen will appear. Leave the User Name field blank. Enter the Router’s password (the default is admin) in the Password field. Then click the OK button.

4.Click the Applications & Gaming tab, and then click the Port Range Forwarding tab.

5.For each port range you must specify, enter a different name in the Application field. Then enter the number or range of external port(s) used by the Phone Adapter.

6.Select the protocol you will be using, UDP.

7.Enter the IP address of the Phone Adapter. For example, if the Phone Adapter’s IP address is 192.168.1.100, you would enter 100 in the field provided.

8.Repeat steps 5-7 until you have entered all four port ranges for the Phone Adapter.

 

Application

Start and End

Protocol

IP Address

Enable

 

 

 

 

 

 

 

 

 

Internet phone 1

5060 to 5061

UDP

(IP address of

X

 

 

 

 

 

Phone Adapter)

 

 

 

 

 

 

 

 

 

 

Internet phone 2

53 to 53

UDP

(IP address of

X

 

 

 

 

 

Phone Adapter)

 

 

 

 

 

 

 

 

 

Appendix A: Troubleshooting

 

 

 

15

Common Problems and Solutions

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Phone Adapter Copyright and Trademarks How to Use this GuideTable of Contents Front Panel Back PanelWelcome IntroductionWhat’s in this Guide? Introduction What’s in this Guide? Back Panel Ports Getting to Know the Phone AdapterFront Panel LEDs Router Phone Adapter Connecting the Phone AdapterInstructions for Connecting the Phone Adapter OverviewConnect the Ethernet Network Cable Remove the plate from the Phone Adapter’s bottom panel Placement OptionsStand Option Wall-Mount OptionAccessing the Interactive Voice Response Menu Using the Phone Adapter’s Interactive Voice Response MenuUsing the Interactive Voice Response Menu Interactive Voice Response Menu Has been enabled or disabled. If121 Enter the network 7932 Enter 1 to enable This feature is protected by a Configuring the Settings for Your Internet Phone Service Entering a PasswordCommon Problems and Solutions Appendix a TroubleshootingIP address Phone Adapter Internet phone 69 to Application Start and End Protocol IP Address EnableInternet phone 5060 to IP address Phone Adapter Internet phone 53 toIP address Phone Adapter Internet phone 69 to IP address Phone Adapter Internet phone 69 to Ethernet LED does not light up Frequently Asked QuestionsShared Resources Appendix B Windows HelpNetwork Neighborhood/My Network Places Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications 10~90% Non-Condensing Storage TempOperating Humidity Storage HumidityLimited Warranty Appendix E Warranty InformationThis product complies with Canadian ICES-003 Appendix F Regulatory InformationLinksys Appendix G Contact Information
Related manuals
Manual 33 pages 13.27 Kb
Top Page Image Contents