Linksys WAP54GPE manual Does the Access Point function as a firewall?

Page 52

Wireless-G Exterior Access Point

What is a MAC Address?

The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a computer logs on to the network, the MAC address of a device stays the same, making it a valuable identifier for the network.

How do I avoid interference?

Using multiple Access Points on the same channel and in close proximity to one another will generate interference. When employing multiple Access Points, make sure to operate each one on a different channel (frequency).

How do I reset the Access Point?

Press the Reset button on the back of the Access Point for about ten seconds. This will reset the unit to its default settings.

How do I resolve issues with signal loss?

There is no way to know the exact range of your wireless network without testing. Every obstacle placed between an Access Point and wireless PC will create signal loss. Leaded glass, metal, concrete floors, water, and walls will inhibit the signal and reduce range. Start with your Access Point and your wireless PC in the same room and move it away in small increments to determine the maximum range in your environment.

You may also try using different channels, as this may eliminate interference affecting only one channel. Also, open the Access Point’s Web-based Utility. Click the Wireless tab and then the Advanced Wireless tab. Make sure the Output Power is set to 100%.

Does the Access Point function as a firewall?

No. The Access Point is only a bridge from wired Ethernet to wireless clients.

I have excellent signal strength, but I cannot see my network.

Wireless security, such as WEP or WPA, is probably enabled on the Access Point, but not on your wireless adapter (or vice versa). Verify that the same wireless security settings are being used on all devices in your wireless network.

What is the maximum number of users the Access Point can handle?

No more than 65, but this depends on the volume of data and may be fewer if many users create a large amount of network traffic.

Appendix A: Troubleshooting

46

Frequently Asked Questions

Image 52

Contents 802 GHz .11g Wireless- G How to Use this User Guide Copyright and TrademarksTable of Contents Appendix B Wireless Security Appendix a TroubleshootingFrequently Asked Questions List of Figures 15 Wireless Advanced Wireless Introduction WelcomeWhat’s in this User Guide? Wireless-G Exterior Access Point Planning Your Wireless Network Network TopologyRoaming Network LayoutExample of a Simple Wireless Network Getting to Know the Wireless-G Exterior Access Point WirelessReceiving data from a wireless device LEDsThat supports Power over Ethernet PoE PortsEthernet AntennaReset Button and Ground Reset Button GroundAntenna Pattern Internal Antenna Pattern Horizontal PlaneWireless-G Exterior Access Point Wireless-G Exterior Access Point Hardware Installation Connecting the Wireless-G Exterior Access PointOverview Ground the Access Point Setting Up the Wireless-G Exterior Access Point Accessing the UtilitySetup WirelessEnter the Host Name and IP Address settings on this screen Navigating the UtilityAdministration AP ModeStatus Configuring the Wireless-G Exterior Access Point Setup TabNetwork Setup IP SettingsSetup Time Tab TimeWireless Network Wireless Basic Wireless Settings TabConfigure the Wireless Network attributes for each Ssid Wireless-G Exterior Access Point Wireless Wireless Security Tab Wireless SecurityDisabled WPA-Personal aka WPA-PSKWPA2-Personal WPA2-Personal MixedWPA-Enterprise WPA2-Enterprise11 Wireless Wireless Security WPA2 Enterprise Mixed WPA2-Enterprise MixedRadius Wireless Connection Control Wireless Wireless Connection Control TabSelect MAC Address From Networked Computers Wireless Advanced Wireless Settings Tab Advanced WirelessWireless-G Exterior Access Point AP Mode Tab MAC AddressWireless Repeater 17 Wireless Repeater18 Site Survey Administration Management Tab AP PasswordWeb Access Local AP PasswordWireless-G Exterior Access Point Administration Log Tab LogWireless-G Exterior Access Point Administration Factory Default Tab Administration Firmware Upgrade TabFactory Default Firmware UpgradeReboot Administration Reboot TabOn this screen you can reboot the Access Point Administration Config Management Tab Config ManagementInformation Status Local Network TabLocal Network Status Wireless Tab 26 Status WirelessWired WirelessStatus System Performance Tab System PerformanceWireless-G Exterior Access Point Appendix a Troubleshooting Frequently Asked QuestionsWhat Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Security Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Exterior Access Point Figure C-1 Firmware Upgrade Appendix C Upgrading FirmwareShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix E Glossary Wireless-G Exterior Access Point Wireless-G Exterior Access Point Wireless-G Exterior Access Point Wireless-G Exterior Access Point Appendix F Specifications ModelStandards IEEE802.11g, IEEE802.11b, IEEE802.3u, IEEE802.3afOperating Humidity Storage HumidityTo 95%, Non-Condensing External antenna is sold separatelyAppendix G Warranty Information Limited WarrantyAppendix H Regulatory Information FCC StatementWireless-G Exterior Access Point Wireless-G Exterior Access Point Wireless-G Exterior Access Point Wireless-G Exterior Access Point Dual-Band Wireless Access Point Appendix I Contact Information Need to contact Linksys?Information section in this Guide Linksys