Motorola MVME712A/D3, MVME712-12, MVME712B Installing the MVME712-13 and MVME712AM as a Modem

Page 29

	Hardware Preparation and Installation
	Installing the MVME712-13 and MVME712AM as a Modem
	To install the MVME712-13 and MVME712AM with serial port 2 configured as
2	a modem, which is the as-shipped configuration, proceed as described in this
2	section. See also Figure 2-8.

Note

If you have connected your module for use with internal SCSI devices, you may already have performed some of these steps.

1.Install the LCP2 adapter module to the backplane directly in line with the P2 connector on the MVME1xx VMEmodule. Be sure to orient pin 1 of the adapter with pin 1 of the backplane connector.

2.Verify that serial port 2 is conÞgured as a modem port (refer to the Serial Port 2 Configuration paragraph).

3.MVME712-13: Attach the cable supplied with the MVME712-13 module from LCP2 adapter connector J2 to connector P2 on the MVME712-13 module. Be sure to orient cable pin 1 with connector pin 1. See Figure 2-8.

MVME712AM: Attach the cable supplied with the MVME712AM module from LCP2 adapter connector J2 to connector J11 on the MVME712AM module. Be sure to orient cable pin 1 with connector pin 1. See Figure 2-8.

4.Connect a user-supplied cable from connector J2 on the MVME712-13 or MVME712AM to backplane connections for +5, +12, and -12 Vdc for modem power.

5.Insert the MVME712-13 or MVME712AM module into the selected slot and tighten the attaching screws.

6.After making sure you will not pinch cables with the cover, reinstall the cover you previously removed.

7.Connect a user-supplied Telco modular cable to the Telco modular jack on the front panel.

8.Connect the power cable to the AC power source and turn on the unit.

2-14	MVME712-12/-13/A/AM/B Transition Modules and LCP2 Adapter Board UserÕs Manual

Image 29

Contents MVME712A/D3 MVME712A, MVME712AMRestricted Rights Legend Document Title Motorola Publication Number PrefaceRelated Documentation Manual Terminology Page Safety Summary Safety Depends On You This equipment generates, uses, and can radiate radio Page Contents Page List of Figures Collective Reference Features of the MVME712 Family ModulesIntroduction Characteristics SpeciÞcations Features of the LCP2 Adapter BoardSpeciﬁcations MVME712 Family SpeciﬁcationsFCC Compliance Cooling RequirementsGeneral Description MVME712x Module Preparation Unpacking InstructionsMVME712-12 Header Locations MVME712x Module Preparation LocationsMVME712AFigure 2-3.Header InstallationHardware PreparationLMVME712AMocationsFigure 2-4.Header DCE DTE DSR Line Pull Up Select Headers J8, J9, J13, J14Ote Serial Port 2/Modem Port 2 Select J16, J17Serial Port Conﬁguration Modem Port ConﬁgurationScsi Termination MVME712B Module PreparationMVME712B Connector Locations LCP2 Adapter Board Preparation LCP2 Adapter Connector LocationsInstallation Instructions Installing for Use with Internal Scsi Devices Internal Scsi and Serial Port Connections Installing the MVME712-13 and MVME712AM as a Modem Internal Scsi and Modem Connections MVME712B Installation MVME712B External Scsi Connections Hardware Preparation and Installation LCP2 and MVME712 Connectors Interconnect SignalsMVME712 Jumpers FromConnectors J1, J3-J5 Interconnect Signals MVME712x Connector P2 Interconnect Signals LCP2 AdapterConnectors J1, J3-J5 Interconnect Signals MVME712x Pin Signal Signal Name and Description Number MnemonicCTS RTSConnector J2 Interconnect Signals LCP2 Adapter Connector J2 Interconnect Signals LCP2 AdapterPrack GND Ground PrfaultPrpe PrbsyTXD1 DTR3GND Ground RXD1 GND Ground RTS1GND Ground TRXC4 RTS4DTR4 CTS4RTS2 CTS2DCD2 DTR2Connector J3 Interconnect Signals LCP2 Adapter Connector Connector J2 Interconnect Signals MVME712-13, MVME712AMConnector J2 Interconnect Signals MVME712-13/AM Connector J3 Interconnect Signals LCP2 AdapterGND Ground DBP Termpwr Terminator PowerGND Ground ATN GND Ground BSYGND Ground REQ Connector Scsi Interface Interconnect Signals MVME712BScsi Interface Interconnect Signals MVME712B GND Ground Termpwr Terminator Power MAU Connector Ethernet Interconnect Signals MVME712BEthernet Interconnect Signals MVME712B Connector J7 Interconnect Signals MVME712-13, MVME712AM Connector J6 Interconnect Signals MVME712-13, MVME712AMConnector J6 Interconnect Signals MVME712-13/AM 10. Connector J7 Interconnect Signals MVME712-13/AM11. Connector J10 Interconnect Signals MVME712x Connector J10 Interconnect Signals MVME712xMDMRXD2 MDMDCD2Pin Number Signal Signal Name and Description J11 Mnemonic Connector P2 and J11 Interconnect Signals MVME712x12. Connector P2, J11 Interconnect Signals MVME712x Data bit 6 Printer A16 A23 13. Connector J12 Interconnect Signals MVME712-13/12AM Connector J12 Interconnect Signals MVME712-13, MVME712AM14. Connector J15 Interconnect Signals MVME712x Connector J15 Interconnect Signals MVME712x15. MVME712 x Module Parts List Parts Lists and LocationsModel Parts List Parts Location Drawing Reference Motorola Description Designation Part Number15. MVME712x Module Parts List Modem kit MVME712-13 and MVME712AM MVME7121.-3FigureocationL-12 Parts SideMVME712-13 Parts Location Drawing Primary Side DrawingFigure 3-3. MVME712A Parts LocationPrimary Side 1532 CR3 CR4 CR5 CR6 CR7 CR8 CR9 PartsMVME712AMFigure 3-4.Location Drawing Primary SideReference Motorola Designation Support Information MVME712A and MVME712AMMVME712B Parts Location Drawing CR1 17. LCP2 Adapter Module Parts ListMVME712AM LCP2 Schematic DrawingsModule Board Part Number Pages Support Information Modem Features BeneÞts Modem FeaturesTable A-1. Modem Features Technical Speciﬁcations Characteristic SpeciÞcationTable A-2. Technical Speciﬁcations TTL/CMOSTable A-3. Autodialer Characteristics Index MVME712AM IN-7