Motorola MVME712B, MVME712A/D3, MVME712-12 Unpacking Instructions, MVME712x Module Preparation

Page 16

HARDWARE PREPARATION AND INSTALLATION

2

Introduction

This chapter provides unpacking instructions, hardware preparation, and installation instructions for the MVME712 family modules and the LCP2 adapter.

Unpacking Instructions

Note

If the carton is damaged upon receipt, request that carrier's agent be present during unpacking and inspection of equipment.

Unpack equipment from shipping carton. Refer to packing list and verify that all items are present. Save packing material for storing and reshipping of equipment.

MVME712x Module Preparation

To select the desired configuration and ensure proper operation of the MVME712x module, certain changes may be made before installation. These changes are made through jumper arrangements on the headers. The locations of the headers and connectors for the MVME712x are illustrated in Figure 2- 1 through Figure 2-4.

The modules have been factory tested and are shipped with factory-installed jumper configurations that are shown in the following paragraphs with each header description. The modules are operational with the factory-installed jumpers. The modules are configured to provide the system functions required for a VMEbus system. Changes may be made for the following reasons:

❏DSR Line Pull Up Select (J8, J9, J13, J14)

❏Serial Port 2/Modem Port 2 Select (J16, J17)

❏Hardwired as DTE (to modem). With the exception of the DSR line, no headers are provided on the module to change this configuration. To use the module as DCE (to terminal), a null modem cable must be attached.

MVME712A/D32-1

Image 16

Contents MVME712A, MVME712AM MVME712A/D3Restricted Rights Legend Related Documentation PrefaceDocument Title Motorola Publication Number Manual Terminology Page Safety Summary Safety Depends On You This equipment generates, uses, and can radiate radio Page Contents Page List of Figures Introduction Features of the MVME712 Family ModulesCollective Reference Features of the LCP2 Adapter Board Characteristics SpeciÞcationsSpeciﬁcations MVME712 Family SpeciﬁcationsCooling Requirements FCC ComplianceGeneral Description Unpacking Instructions MVME712x Module PreparationMVME712-12 Header Locations MVME712x Module Preparation InstallationHardware Preparation LocationsMVME712AFigure 2-3.HeaderLMVME712AMocationsFigure 2-4.Header DSR Line Pull Up Select Headers J8, J9, J13, J14 DCE DTESerial Port 2/Modem Port 2 Select J16, J17 OteSerial Port Conﬁguration Modem Port ConﬁgurationMVME712B Module Preparation Scsi TerminationMVME712B Connector Locations LCP2 Adapter Connector Locations LCP2 Adapter Board PreparationInstallation Instructions Installing for Use with Internal Scsi Devices Internal Scsi and Serial Port Connections Installing the MVME712-13 and MVME712AM as a Modem Internal Scsi and Modem Connections MVME712B Installation MVME712B External Scsi Connections Hardware Preparation and Installation Interconnect Signals LCP2 and MVME712 ConnectorsMVME712 Jumpers FromConnector P2 Interconnect Signals LCP2 Adapter Connectors J1, J3-J5 Interconnect Signals MVME712xConnectors J1, J3-J5 Interconnect Signals MVME712x Pin Signal Signal Name and Description Number MnemonicRTS CTSConnector J2 Interconnect Signals LCP2 Adapter Connector J2 Interconnect Signals LCP2 AdapterGND Ground Prfault PrackPrpe PrbsyDTR3 TXD1GND Ground RXD1 GND Ground RTS1RTS4 GND Ground TRXC4DTR4 CTS4CTS2 RTS2DCD2 DTR2Connector J2 Interconnect Signals MVME712-13, MVME712AM Connector J3 Interconnect Signals LCP2 Adapter ConnectorConnector J2 Interconnect Signals MVME712-13/AM Connector J3 Interconnect Signals LCP2 AdapterTermpwr Terminator Power GND Ground DBPGND Ground ATN GND Ground BSYScsi Interface Interconnect Signals MVME712B Connector Scsi Interface Interconnect Signals MVME712BGND Ground REQ GND Ground Termpwr Terminator Power Ethernet Interconnect Signals MVME712B Connector Ethernet Interconnect Signals MVME712BMAU Connector J6 Interconnect Signals MVME712-13, MVME712AM Connector J7 Interconnect Signals MVME712-13, MVME712AMConnector J6 Interconnect Signals MVME712-13/AM 10. Connector J7 Interconnect Signals MVME712-13/AMConnector J10 Interconnect Signals MVME712x 11. Connector J10 Interconnect Signals MVME712xMDMRXD2 MDMDCD212. Connector P2, J11 Interconnect Signals MVME712x Connector P2 and J11 Interconnect Signals MVME712xPin Number Signal Signal Name and Description J11 Mnemonic Data bit 6 Printer A16 A23 Connector J12 Interconnect Signals MVME712-13, MVME712AM 13. Connector J12 Interconnect Signals MVME712-13/12AMConnector J15 Interconnect Signals MVME712x 14. Connector J15 Interconnect Signals MVME712xParts Lists and Locations 15. MVME712 x Module Parts ListModel Parts List Parts Location Drawing Reference Motorola Description Designation Part Number15. MVME712x Module Parts List Modem kit MVME712-13 and MVME712AM Side MVME7121.-3FigureocationL-12 PartsMVME712-13 Parts Location Drawing Primary Side DrawingFigure 3-3. MVME712A Parts LocationPrimary Side 1532 PartsMVME712AMFigure 3-4.Location Drawing Primary Side CR3 CR4 CR5 CR6 CR7 CR8 CR9Support Information MVME712A and MVME712AM Reference Motorola DesignationMVME712B Parts Location Drawing 17. LCP2 Adapter Module Parts List CR1Module Board Part Number Pages Schematic DrawingsMVME712AM LCP2 Support Information Modem Table A-1. Modem Features Modem FeaturesFeatures BeneÞts Characteristic SpeciÞcation Technical SpeciﬁcationsTable A-2. Technical Speciﬁcations TTL/CMOSTable A-3. Autodialer Characteristics Index MVME712AM IN-7