3Com 10/100BASE-T4 AutoLink Installation, At the prompt, type, Alternatively, at the prompt, type

Page 26

3-6 CHAPTER 3: LOADING THE NETWORK DRIVERS

AutoLink Installation

To use the AutoLink program to install NetWare DOS ODI client software on a PC with a single adapter, follow these steps:

1Make sure that you have booted the computer under DOS, version 3.1 or later, and that your computer is connected to the network, as detailed in Chapter 2.

2Insert the EtherDisk diskette in a ﬂoppy drive on your computer and make that drive the active drive.

For example, if the ﬂoppy drive is A, type the following command:

A:[Enter]

3At the prompt, type:

INSTALL [Enter]

Alternatively, at the prompt, type:

AUTOLINK [Enter]

If you type AUTOLINK instead of INSTALL, you will bypass the EtherDisk diskette menu program (skipping steps 5 and 6) and advance to step 7.

4The ﬁrst time you use the diskette to install an adapter, a license screen appears. To accept the terms and conditions of the 3Com end-user software license agreement, type the following:

Y

To view the full text of the license agreement, press [F1].

Once you have agreed to the terms and conditions of the 3Com license agreement, the license screen will not appear again.

The Auto Installation Information screen appears, as shown in Figure 3-1.

Image 26

Contents User Guide Fast Etherlink Parallel TaskingNetwork Adapter Adapters3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty Asia Contents Configuring Software Settings Cispr B Compliance Figures Tables Introduction How to Use This GuideAbout this Guide Conventions Print Autolink.logAdapter automatically senses and switches to either Introduction10/100BASE-T4 PCI Adapter Adapter Features PCI Technology 3C59X EtherDisk diskette version 5.1 or above Installing the AdapterInspecting the Adapter Installing the Boot Prom Installing the AdapterConnecting to the Network PCI Computer with PCI and Eisa SlotsRJ-45 connector Connecting to the Network Drivers Summary of Driver Loading ProceduresLoading the Network Using the EtherDisk Diskette Accessing DOSUsing Windows Name of the installed 3Com adapter appears, as follows Conﬁrming Adapter Installation for WindowsSystem Properties box appears, detailing your system setup This conﬁrms the adapter’s installationAutoLink Requirements Using NetWare ODIOne Adapter in a Client Alternatively, at the prompt, type AutoLink InstallationAt the prompt, type ESC=Cancel Read the screen and press EnterMultiple Adapters in a Client FEA0 Select Conﬁguration and Diagnostic Program and press Enter Main menu appearsLoading Ndis Drivers One or More Adapters in a ServerFollow the instructions displayed in the subsequent screens Updating Ndis DriversAuto Select Media Type Transcend PC Link SmartAgent Driver Agents Desktop Management InterfacePerforming Troubleshooting Diagnostic Tests Troubleshooting with the Diagnostic TestsTypes of Tests After performing the diagnostic tests, reboot your computerBefore Running the Tests Fast EtherLink 10/100BASE-T4 PCI adapterStarting the Diagnostic Program Running the Group 1 TestsRunning the Group 3 Test Setting Up an Echo Server 3C59XCFG Getting Help If a Test Fails To print the ﬁle, type To change the test parameters, follow these steps Changing the Test SetupMiscellaneous Checks LEDs LEDCabling Pin assignments for the RJ-45 connectorWhen properly connected to a 10BASE-T network, Adapter Cabling RequirementsTwisted-Pair Cable 10BASE-T Operation 10BASE-T Speciﬁcations100BASE-TX designates the Ieee 802.3 speciﬁcation for 100BASE-T Standard100BASE-TX Operation 100BASE-T4 Operation 100BASE-FX OperationRJ-45 Connector Pin Assignments Figure A-1 shows the RJ-45 connector pin assignmentsSettings Type at the prompt Changing Software SettingsTo change the software option settings, follow these steps Select Adapter Installed Adapters Continue this procedure with any of the other options Press Tab to highlight OK. Press Enter\CONFIG\3C595.SET Specifications Adapter SpeciﬁcationsTechnical Support On-line Technical Services3Com Bulletin Board Service To use 3ComForum Log on to CompuServe World Wide Web Site3ComForum on CompuServe Press Return to see the 3ComForum main menuLocal numbers are available within the following countries 3ComFacts Automated Fax ServiceSupport from Your Network Supplier To obtain an RMA number, call or fax Returning Products for RepairDetails about recent conﬁguration changes, if applicable Glossary 100BASE-TAuto Select Media Type BusEIA/TIA EMM386MAC STP Index NumericsDOS Ndis Network Driver Optimization option setting B-2 Windows 3.X 3-3 Windows Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook CE Notice