Asus P4 533 manual Hardware Monitor, CPU Q-Fan Function Enabled, CPU Temperature Threshold 55C

Page 81

4.5.2Hardware Monitor

CPU Q-Fan Function [Enabled]

This item allows you to enable or disable the ASUS Q-Fan feature that smartly adjusts the CPU fan speed for more efficient system operation. Configuration options: [Disabled] [Enabled]

CPU Temperature Threshold [55°C]

This item allows you to set the highest temperature for the CPU so that when exceeded by the actual CPU temperature, Q-Fan supplies more power to the CPU fan. When the CPU temperature goes below the setting, Q-Fan automatically reverts to the normal power supplied to the fan. Configuration options: [50°C] [55°C] [60°C] [65°C] [70°C]

CPU Fan Lowest Level Voltage [9V]

This item allows you to set the lowest voltage applied to the CPU fan. Configuration options: [6V] [6.5V] [7V] [7.5] [8V] [8.5] [9V]

PWR Q-Fan Function [Enabled]

This item allows you to enable or disable the ASUS Q-Fan feature that smartly adjusts the power fan speed for more efficient system operation. Configuration options: [Disabled] [Enabled]

ASUS Terminator P4 533 Barebone System

81

Image 81

Contents Terminator P4 Disclaimer/Copyrights 00 E1032June Table of contents Starting up Bios InformationFCC/CDC statements Federal Communications Commission StatementCanadian Department of Communications Statement Electrical safety Safety informationThis document contains the following parts About this guideSystem Introduction Motherboard InformationOptional Documentation Asus WebsitesASUSTeK Computer INC. Asia-Pacific Asus contact informationAsus Computer International America Asus Computer GmbH EuropeSystem package contents Asus Terminator P4 533 Barebone System ChapterChassis Front Panel FeaturesVoltage Selector Rear Panel FeaturesInternal Features Basic Installation TIP Remove the coverFollow these steps to detach the drive frame Detach the drive frameDrive frame Swivel edge Install a CPU Socket until it fits in place Carefully insert the CPU intoInstall the CPU heatsink and fan Follow to lock the second bracket Dimm Install system memoryInstall a hard disk drive Follow these steps to install an IDEPlace the chassis upright Red Stripe to Pin IDE Ribbon Cable Secure the CD-ROM with two screws on each side of the bay Install a CD-ROM drivePin connector at the back of the CD-ROM Install a PCI expansion card Press the card firmly until it isProperly seated on the slot Re-connect cables LED cablesConnect the HDD LED cable to the 2-pin lead marked IDELED1 Uaex Uaex and USB-CF extension modulesTurn the chassis upright Replace the coverRail Tabs Connect External Devices Input Characteristics Output CharacteristicsOver-Voltage Protection OVP Motherboard Info Introduction Motherboard componentsChapter Asus Terminator P4 533 Barebone System Motherboard information Super Motherboard layoutCentral Processing Unit CPU System memory Memory configurationsExpansion slots Configuring an expansion cardStandard Interrupt Assignments IRQ assignments for this motherboardUSB device wake-up 3-pin USBPWR12, USBPWR34, USBPWR56 JumpersClear RTC RAM CLRTC1 IDE connectors 40-1 pin PRIIDE1, SECIDE1 ConnectorsHard disk activity LED 2-pin IDELED1 Floppy disk drive connector 34-1 pin FLOPPY1ATXPWR1 ATX power connectors 20-pin ATXPWR, 4-pin ATX +12VP4SC-E 12-Volt Cooling Fan Power USB headers 10-1 pin USB2 Internal audio connectors 4-pin AUX1, CD1, MODEM1Front panel audio connectors 5-1 pin MICLOUT1 System Power LED Lead 3-1 pin Pled System panel connector 20-pin PANEL1System Warning Speaker Lead 4-pin Speaker System Message LED Lead 2-pin MledReset Switch Lead 2-pin Reset ATX Power Switch / Soft-Off Switch Lead 2-pin PWRBios Information Managing and updating the Bios Using the computer system for the first timeReboot the computer from the floppy disk DOS mode, type A\AFLASH Enter to run Aflash Updating Bios procedures Asus Terminator P4 533 Barebone System Bios Setup program Navigation Keys Function Description Bios menu barGeneral help Saving changes and exiting the Setup programScroll bar Sub-menuMain Menu Floppy 3 Mode Support DisabledSystem Time System Date XX/XX/XXXXForgot the password? Supervisor Password Disabled / User Password DisabledHalt On All Errors Installed Memory XXX MBType Auto Primary and Secondary Master/SlaveUser Type HDD Cylinders Translation Method LBAHead SectorSmart Monitoring Disabled PIO ModeUltra DMA Mode Disabled Boot Up NumLock Status On Keyboard FeaturesKeyboard Auto-Repeat Delay 1/4 Sec Keyboard Auto-Repeat Rate 12/SecAdvanced Menu CPU Speed ManualCPU/PCI Frequency MHz Bios Update Enabled CPU Level 2 Cache EnabledOS/2 Onboard Memory 64M Disabled Memory Frequency AutoSdram Configuration By SPD Chip ConfigurationSdram RAS to CAS Delay 3T Sdram CAS Latency 2TAGP Capability 4X Mode Sdram Command Lead-off Time AutoAGP Fast Write Capability Disabled Video Memory Cache Mode UCPCI 2.1 Support Enabled 2 I/O Device ConfigurationIDE Bus Master Support Enabled Onboard PCI IDE BothParallel Port Mode ECP+EPP Floppy Disk Access Control R/WOnboard Midi I/O Disabled Onboard Serial Port 1 3F8H/IRQ4PCI Configuration USB 2.0 Function Enabled USB Function EnabledOnboard LAN Boot ROM Disabled Onboard PCI Devices Control Onboard LAN EnabledPCI IRQ Resource Exclusion IRQ XX Reserved No/ICU Onboard AC97 Audio Controller AutoPower Management User Defined Power MenuAcpi Suspend To RAM Enabled HDD Power Down DisabledSuspend Mode Disabled Video Off Option Suspend OffAC PWR Loss Restart Disabled Power Up ControlWake/Power Up On Ext. Modem Disabled Power Up On PCI Card DisabledAutomatic Power Up Disabled Power On By PS/2 Keyboard Space BarCPU Temperature Threshold 55C CPU Q-Fan Function EnabledPWR Q-Fan Function Enabled Hardware MonitorPower Temperature xxxC/xxxF CPU Temperature xxxC/xxxF PWR Temperature Threshold 55CPWR Fan Lowest Level Voltage CPU Fan Speed xxxxRPM Chassis Fan Speed xxxxRPMBoot Sequence Boot MenuOther Boot Device Select INT18 Device Network Removable Device Legacy FloppyQuick Power On Self Test Enabled Boot Virus Detection EnabledBoot Up Floppy Seek Enabled Full Screen Logo EnabledExit Menu Exit Saving ChangesExit Discarding Changes Load Setup Defaults Discard ChangesSave Changes Starting up Install an operating system Support CD informationRunning the support CD Installation menus Software and drivers description Show Motherboard Information Asus Screen SaverBrowse Support CD ReadmeAsus Update Asus Update initial screen appearsSoftware information Asus Terminator P4 533 Barebone System Starting Asus PC Probe Asus PC ProbeTemperature Monitor Using Asus PC ProbeMonitor Summary Fan MonitorHistory SettingsFan Control Hard DrivesMemory Device SummaryDMI Explorer Asus PC Probe Task Bar Icon