Asus P4 533 manual ATX power connectors 20-pin ATXPWR, 4-pin ATX +12V, ATXPWR1

Page 47

4.ATX power connectors (20-pin ATXPWR, 4-pin ATX +12V)

These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.

In addition to the 20-pin ATXPWR connector, this motherboard requires that you connect the 4-pin ATX +12V power plug to provide sufficient power to the CPU.


	ATXPWR1	+12.0Volts		+5.0 Volts
		+5V Standby		+5.0 Volts
		Power Good		-5.0 Volts
		Ground		Ground
		+5.0 Volts		Ground
		Ground		Ground
	P4SC-E	+5.0 Volts		Power Supply On
	P4SC-E	Ground		Ground
		Ground		Ground
		+3.3 Volts		-12.0Volts
		+3.3 Volts		+3.3Volts
	ATX12V1		COM	+12V DC

P4SC-E ATX Power Connector

COM +12V DC

IMPORTANT

If you will need to replace the power supply in the future, make sure that your new ATX 12V power supply can provide 8A on the +12V lead and at least 1A on the +5-volt standby lead (+5VSB). The minimum recommended wattage is 230W, or 300W for a fully configured system. The system may become unstable and may experience difficulty powering up if the power supply is inadequate.

ASUS Terminator P4 533 Barebone System

47

Image 47

Contents Terminator P4 June Disclaimer/Copyrights00 E1032 Table of contents Starting up Bios InformationCanadian Department of Communications Statement FCC/CDC statementsFederal Communications Commission Statement Electrical safety Safety informationMotherboard Information About this guideThis document contains the following parts System IntroductionOptional Documentation Asus WebsitesAsus Computer GmbH Europe Asus contact informationASUSTeK Computer INC. Asia-Pacific Asus Computer International AmericaSystem package contents Asus Terminator P4 533 Barebone System ChapterChassis Front Panel FeaturesVoltage Selector Rear Panel FeaturesInternal Features Basic Installation TIP Remove the coverFollow these steps to detach the drive frame Detach the drive frameDrive frame Swivel edge Install a CPU Socket until it fits in place Carefully insert the CPU intoInstall the CPU heatsink and fan Follow to lock the second bracket Dimm Install system memoryPlace the chassis upright Install a hard disk driveFollow these steps to install an IDE Red Stripe to Pin IDE Ribbon Cable Secure the CD-ROM with two screws on each side of the bay Install a CD-ROM drivePin connector at the back of the CD-ROM Properly seated on the slot Install a PCI expansion cardPress the card firmly until it is Connect the HDD LED cable to the 2-pin lead marked IDELED1 Re-connect cablesLED cables Uaex Uaex and USB-CF extension modulesTurn the chassis upright Replace the coverRail Tabs Connect External Devices Over-Voltage Protection OVP Input CharacteristicsOutput Characteristics Motherboard Info Chapter IntroductionMotherboard components Asus Terminator P4 533 Barebone System Motherboard information Super Motherboard layoutCentral Processing Unit CPU System memory Memory configurationsIRQ assignments for this motherboard Configuring an expansion cardExpansion slots Standard Interrupt AssignmentsUSB device wake-up 3-pin USBPWR12, USBPWR34, USBPWR56 JumpersClear RTC RAM CLRTC1 IDE connectors 40-1 pin PRIIDE1, SECIDE1 ConnectorsHard disk activity LED 2-pin IDELED1 Floppy disk drive connector 34-1 pin FLOPPY1ATXPWR1 ATX power connectors 20-pin ATXPWR, 4-pin ATX +12VP4SC-E 12-Volt Cooling Fan Power USB headers 10-1 pin USB2 Internal audio connectors 4-pin AUX1, CD1, MODEM1Front panel audio connectors 5-1 pin MICLOUT1 System Message LED Lead 2-pin Mled System panel connector 20-pin PANEL1System Power LED Lead 3-1 pin Pled System Warning Speaker Lead 4-pin SpeakerReset Switch Lead 2-pin Reset ATX Power Switch / Soft-Off Switch Lead 2-pin PWRBios Information Reboot the computer from the floppy disk Managing and updating the BiosUsing the computer system for the first time DOS mode, type A\AFLASH Enter to run Aflash Updating Bios procedures Asus Terminator P4 533 Barebone System Bios Setup program Navigation Keys Function Description Bios menu barSub-menu Saving changes and exiting the Setup programGeneral help Scroll barSystem Date XX/XX/XXXX Floppy 3 Mode Support DisabledMain Menu System TimeInstalled Memory XXX MB Supervisor Password Disabled / User Password DisabledForgot the password? Halt On All ErrorsType Auto Primary and Secondary Master/SlaveUser Type HDD Sector Translation Method LBACylinders HeadUltra DMA Mode Disabled Smart Monitoring DisabledPIO Mode Keyboard Auto-Repeat Rate 12/Sec Keyboard FeaturesBoot Up NumLock Status On Keyboard Auto-Repeat Delay 1/4 SecCPU/PCI Frequency MHz Advanced MenuCPU Speed Manual Memory Frequency Auto CPU Level 2 Cache EnabledBios Update Enabled OS/2 Onboard Memory 64M DisabledSdram CAS Latency 2T Chip ConfigurationSdram Configuration By SPD Sdram RAS to CAS Delay 3TVideo Memory Cache Mode UC Sdram Command Lead-off Time AutoAGP Capability 4X Mode AGP Fast Write Capability DisabledOnboard PCI IDE Both 2 I/O Device ConfigurationPCI 2.1 Support Enabled IDE Bus Master Support EnabledOnboard Serial Port 1 3F8H/IRQ4 Floppy Disk Access Control R/WParallel Port Mode ECP+EPP Onboard Midi I/O DisabledPCI Configuration Onboard PCI Devices Control Onboard LAN Enabled USB Function EnabledUSB 2.0 Function Enabled Onboard LAN Boot ROM DisabledPCI IRQ Resource Exclusion IRQ XX Reserved No/ICU Onboard AC97 Audio Controller AutoPower Management User Defined Power MenuVideo Off Option Suspend Off HDD Power Down DisabledAcpi Suspend To RAM Enabled Suspend Mode DisabledPower Up On PCI Card Disabled Power Up ControlAC PWR Loss Restart Disabled Wake/Power Up On Ext. Modem DisabledAutomatic Power Up Disabled Power On By PS/2 Keyboard Space BarHardware Monitor CPU Q-Fan Function EnabledCPU Temperature Threshold 55C PWR Q-Fan Function EnabledCPU Fan Speed xxxxRPM Chassis Fan Speed xxxxRPM PWR Temperature Threshold 55CPower Temperature xxxC/xxxF CPU Temperature xxxC/xxxF PWR Fan Lowest Level VoltageRemovable Device Legacy Floppy Boot MenuBoot Sequence Other Boot Device Select INT18 Device NetworkFull Screen Logo Enabled Boot Virus Detection EnabledQuick Power On Self Test Enabled Boot Up Floppy Seek EnabledExit Discarding Changes Exit MenuExit Saving Changes Save Changes Load Setup DefaultsDiscard Changes Starting up Running the support CD Install an operating systemSupport CD information Installation menus Software and drivers description Readme Asus Screen SaverShow Motherboard Information Browse Support CDSoftware information Asus UpdateAsus Update initial screen appears Asus Terminator P4 533 Barebone System Starting Asus PC Probe Asus PC ProbeFan Monitor Using Asus PC ProbeTemperature Monitor Monitor SummaryHard Drives SettingsHistory Fan ControlDMI Explorer MemoryDevice Summary Asus PC Probe Task Bar Icon