Asus P4 533 manual Rear Panel Features, Voltage Selector

Page 13

1.2Rear Panel Features

The rear panel of the ASUS Terminator P4 533 barebone system includes the standard PC99 I/O connectors for external devices, power supply socket, and optional modem connectors.

The following figure shows the rear panel features.

Game/MIDI Connector

Serial Port (COM1)

PS/2 Mouse Connector

PS/2 Keyboard Connector

VGA Port

Parallel Connector

Line Out Connector

Line In Connector

Microphone Connector

LAN Connector (RJ-45)

USB Connectors (Ports 0&1)

Modem (optional)

Power Socket

Voltage Selector

The switching power supply that came with the system has a voltage selector switch below the power socket. Use this switch to select the appropriate voltage according to the voltage supply in your area.

If the voltage supply in your area is 100-127V, set the switch to 115V.

If the voltage supply in your area is 200-240V, set the switch to 230V.

115V/230V Voltage Selector

CAUTION!

Setting the switch to 115V in a 230V environment will seriously damage the system!

ASUS Terminator P4 533 Barebone System

13

Image 13

Contents Terminator P4 00 E1032 Disclaimer/CopyrightsJune Table of contents Starting up Bios InformationFederal Communications Commission Statement FCC/CDC statementsCanadian Department of Communications Statement Electrical safety Safety informationThis document contains the following parts About this guideSystem Introduction Motherboard InformationOptional Documentation Asus WebsitesASUSTeK Computer INC. Asia-Pacific Asus contact informationAsus Computer International America Asus Computer GmbH EuropeSystem package contents Asus Terminator P4 533 Barebone System ChapterChassis Front Panel FeaturesVoltage Selector Rear Panel FeaturesInternal Features Basic Installation TIP Remove the coverFollow these steps to detach the drive frame Detach the drive frameDrive frame Swivel edge Install a CPU Socket until it fits in place Carefully insert the CPU intoInstall the CPU heatsink and fan Follow to lock the second bracket Dimm Install system memoryFollow these steps to install an IDE Install a hard disk drivePlace the chassis upright Red Stripe to Pin IDE Ribbon Cable Secure the CD-ROM with two screws on each side of the bay Install a CD-ROM drivePin connector at the back of the CD-ROM Press the card firmly until it is Install a PCI expansion cardProperly seated on the slot LED cables Re-connect cablesConnect the HDD LED cable to the 2-pin lead marked IDELED1 Uaex Uaex and USB-CF extension modulesTurn the chassis upright Replace the coverRail Tabs Connect External Devices Output Characteristics Input CharacteristicsOver-Voltage Protection OVP Motherboard Info Motherboard components IntroductionChapter Asus Terminator P4 533 Barebone System Motherboard information Super Motherboard layoutCentral Processing Unit CPU System memory Memory configurationsExpansion slots Configuring an expansion cardStandard Interrupt Assignments IRQ assignments for this motherboardUSB device wake-up 3-pin USBPWR12, USBPWR34, USBPWR56 JumpersClear RTC RAM CLRTC1 IDE connectors 40-1 pin PRIIDE1, SECIDE1 ConnectorsHard disk activity LED 2-pin IDELED1 Floppy disk drive connector 34-1 pin FLOPPY1ATXPWR1 ATX power connectors 20-pin ATXPWR, 4-pin ATX +12VP4SC-E 12-Volt Cooling Fan Power USB headers 10-1 pin USB2 Internal audio connectors 4-pin AUX1, CD1, MODEM1Front panel audio connectors 5-1 pin MICLOUT1 System Power LED Lead 3-1 pin Pled System panel connector 20-pin PANEL1System Warning Speaker Lead 4-pin Speaker System Message LED Lead 2-pin MledReset Switch Lead 2-pin Reset ATX Power Switch / Soft-Off Switch Lead 2-pin PWRBios Information Using the computer system for the first time Managing and updating the BiosReboot the computer from the floppy disk DOS mode, type A\AFLASH Enter to run Aflash Updating Bios procedures Asus Terminator P4 533 Barebone System Bios Setup program Navigation Keys Function Description Bios menu barGeneral help Saving changes and exiting the Setup programScroll bar Sub-menuMain Menu Floppy 3 Mode Support DisabledSystem Time System Date XX/XX/XXXXForgot the password? Supervisor Password Disabled / User Password DisabledHalt On All Errors Installed Memory XXX MBType Auto Primary and Secondary Master/SlaveUser Type HDD Cylinders Translation Method LBAHead SectorPIO Mode Smart Monitoring DisabledUltra DMA Mode Disabled Boot Up NumLock Status On Keyboard FeaturesKeyboard Auto-Repeat Delay 1/4 Sec Keyboard Auto-Repeat Rate 12/SecCPU Speed Manual Advanced MenuCPU/PCI Frequency MHz Bios Update Enabled CPU Level 2 Cache EnabledOS/2 Onboard Memory 64M Disabled Memory Frequency AutoSdram Configuration By SPD Chip ConfigurationSdram RAS to CAS Delay 3T Sdram CAS Latency 2TAGP Capability 4X Mode Sdram Command Lead-off Time AutoAGP Fast Write Capability Disabled Video Memory Cache Mode UCPCI 2.1 Support Enabled 2 I/O Device ConfigurationIDE Bus Master Support Enabled Onboard PCI IDE BothParallel Port Mode ECP+EPP Floppy Disk Access Control R/WOnboard Midi I/O Disabled Onboard Serial Port 1 3F8H/IRQ4PCI Configuration USB 2.0 Function Enabled USB Function EnabledOnboard LAN Boot ROM Disabled Onboard PCI Devices Control Onboard LAN EnabledPCI IRQ Resource Exclusion IRQ XX Reserved No/ICU Onboard AC97 Audio Controller AutoPower Management User Defined Power MenuAcpi Suspend To RAM Enabled HDD Power Down DisabledSuspend Mode Disabled Video Off Option Suspend OffAC PWR Loss Restart Disabled Power Up ControlWake/Power Up On Ext. Modem Disabled Power Up On PCI Card DisabledAutomatic Power Up Disabled Power On By PS/2 Keyboard Space BarCPU Temperature Threshold 55C CPU Q-Fan Function EnabledPWR Q-Fan Function Enabled Hardware MonitorPower Temperature xxxC/xxxF CPU Temperature xxxC/xxxF PWR Temperature Threshold 55CPWR Fan Lowest Level Voltage CPU Fan Speed xxxxRPM Chassis Fan Speed xxxxRPMBoot Sequence Boot MenuOther Boot Device Select INT18 Device Network Removable Device Legacy FloppyQuick Power On Self Test Enabled Boot Virus Detection EnabledBoot Up Floppy Seek Enabled Full Screen Logo EnabledExit Saving Changes Exit MenuExit Discarding Changes Discard Changes Load Setup DefaultsSave Changes Starting up Support CD information Install an operating systemRunning the support CD Installation menus Software and drivers description Show Motherboard Information Asus Screen SaverBrowse Support CD ReadmeAsus Update initial screen appears Asus UpdateSoftware information Asus Terminator P4 533 Barebone System Starting Asus PC Probe Asus PC ProbeTemperature Monitor Using Asus PC ProbeMonitor Summary Fan MonitorHistory SettingsFan Control Hard DrivesDevice Summary MemoryDMI Explorer Asus PC Probe Task Bar Icon