Asus P4 533 Power Up Control, AC PWR Loss Restart Disabled, Wake/Power Up On Ext. Modem Disabled

Page 79

4.5.1Power Up Control

AC PWR Loss Restart [Disabled]

This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption. Configuration options: [Disabled] [Enabled] [Previous State]

Wake/Power Up On Ext. Modem [Disabled]

This allows either settings of [Enabled] or [Disabled] for powering up the computer when the external modem receives a call while the computer is in Soft-off mode. Configuration options: [Disabled] [Enabled]

NOTE

The computer cannot receive or transmit data until the computer and applications are fully running. Thus, connection cannot be made on the first try. Turning an external modem off and then back on while the computer is off causes an initialization string that turns the system power on.

Power Up On PCI Card [Disabled]

When set to [Enabled], this parameter allows you to turn on the system through a PCI modem. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled]

ASUS Terminator P4 533 Barebone System

79

Image 79

Contents Terminator P4 00 E1032 Disclaimer/CopyrightsJune Table of contents Starting up Bios InformationFederal Communications Commission Statement FCC/CDC statementsCanadian Department of Communications Statement Electrical safety Safety informationMotherboard Information About this guideThis document contains the following parts System IntroductionOptional Documentation Asus WebsitesAsus Computer GmbH Europe Asus contact informationASUSTeK Computer INC. Asia-Pacific Asus Computer International AmericaSystem package contents Asus Terminator P4 533 Barebone System ChapterChassis Front Panel FeaturesVoltage Selector Rear Panel FeaturesInternal Features Basic Installation TIP Remove the coverFollow these steps to detach the drive frame Detach the drive frameDrive frame Swivel edge Install a CPU Socket until it fits in place Carefully insert the CPU intoInstall the CPU heatsink and fan Follow to lock the second bracket Dimm Install system memoryFollow these steps to install an IDE Install a hard disk drivePlace the chassis upright Red Stripe to Pin IDE Ribbon Cable Secure the CD-ROM with two screws on each side of the bay Install a CD-ROM drivePin connector at the back of the CD-ROM Press the card firmly until it is Install a PCI expansion cardProperly seated on the slot LED cables Re-connect cablesConnect the HDD LED cable to the 2-pin lead marked IDELED1 Uaex Uaex and USB-CF extension modulesTurn the chassis upright Replace the coverRail Tabs Connect External Devices Output Characteristics Input CharacteristicsOver-Voltage Protection OVP Motherboard Info Motherboard components IntroductionChapter Asus Terminator P4 533 Barebone System Motherboard information Super Motherboard layoutCentral Processing Unit CPU System memory Memory configurationsIRQ assignments for this motherboard Configuring an expansion cardExpansion slots Standard Interrupt AssignmentsUSB device wake-up 3-pin USBPWR12, USBPWR34, USBPWR56 JumpersClear RTC RAM CLRTC1 IDE connectors 40-1 pin PRIIDE1, SECIDE1 ConnectorsHard disk activity LED 2-pin IDELED1 Floppy disk drive connector 34-1 pin FLOPPY1ATXPWR1 ATX power connectors 20-pin ATXPWR, 4-pin ATX +12VP4SC-E 12-Volt Cooling Fan Power USB headers 10-1 pin USB2 Internal audio connectors 4-pin AUX1, CD1, MODEM1Front panel audio connectors 5-1 pin MICLOUT1 System Message LED Lead 2-pin Mled System panel connector 20-pin PANEL1System Power LED Lead 3-1 pin Pled System Warning Speaker Lead 4-pin SpeakerReset Switch Lead 2-pin Reset ATX Power Switch / Soft-Off Switch Lead 2-pin PWRBios Information Using the computer system for the first time Managing and updating the BiosReboot the computer from the floppy disk DOS mode, type A\AFLASH Enter to run Aflash Updating Bios procedures Asus Terminator P4 533 Barebone System Bios Setup program Navigation Keys Function Description Bios menu barSub-menu Saving changes and exiting the Setup programGeneral help Scroll barSystem Date XX/XX/XXXX Floppy 3 Mode Support DisabledMain Menu System TimeInstalled Memory XXX MB Supervisor Password Disabled / User Password DisabledForgot the password? Halt On All ErrorsType Auto Primary and Secondary Master/SlaveUser Type HDD Sector Translation Method LBACylinders HeadPIO Mode Smart Monitoring DisabledUltra DMA Mode Disabled Keyboard Auto-Repeat Rate 12/Sec Keyboard FeaturesBoot Up NumLock Status On Keyboard Auto-Repeat Delay 1/4 SecCPU Speed Manual Advanced MenuCPU/PCI Frequency MHz Memory Frequency Auto CPU Level 2 Cache EnabledBios Update Enabled OS/2 Onboard Memory 64M DisabledSdram CAS Latency 2T Chip ConfigurationSdram Configuration By SPD Sdram RAS to CAS Delay 3TVideo Memory Cache Mode UC Sdram Command Lead-off Time AutoAGP Capability 4X Mode AGP Fast Write Capability DisabledOnboard PCI IDE Both 2 I/O Device ConfigurationPCI 2.1 Support Enabled IDE Bus Master Support EnabledOnboard Serial Port 1 3F8H/IRQ4 Floppy Disk Access Control R/WParallel Port Mode ECP+EPP Onboard Midi I/O DisabledPCI Configuration Onboard PCI Devices Control Onboard LAN Enabled USB Function EnabledUSB 2.0 Function Enabled Onboard LAN Boot ROM Disabled PCI IRQ Resource Exclusion IRQ XX Reserved No/ICU Onboard AC97 Audio Controller AutoPower Management User Defined Power MenuVideo Off Option Suspend Off HDD Power Down DisabledAcpi Suspend To RAM Enabled Suspend Mode DisabledPower Up On PCI Card Disabled Power Up ControlAC PWR Loss Restart Disabled Wake/Power Up On Ext. Modem DisabledAutomatic Power Up Disabled Power On By PS/2 Keyboard Space BarHardware Monitor CPU Q-Fan Function EnabledCPU Temperature Threshold 55C PWR Q-Fan Function EnabledCPU Fan Speed xxxxRPM Chassis Fan Speed xxxxRPM PWR Temperature Threshold 55CPower Temperature xxxC/xxxF CPU Temperature xxxC/xxxF PWR Fan Lowest Level VoltageRemovable Device Legacy Floppy Boot MenuBoot Sequence Other Boot Device Select INT18 Device NetworkFull Screen Logo Enabled Boot Virus Detection EnabledQuick Power On Self Test Enabled Boot Up Floppy Seek EnabledExit Saving Changes Exit MenuExit Discarding Changes Discard Changes Load Setup DefaultsSave Changes Starting up Support CD information Install an operating systemRunning the support CD Installation menus Software and drivers description Readme Asus Screen SaverShow Motherboard Information Browse Support CDAsus Update initial screen appears Asus UpdateSoftware information Asus Terminator P4 533 Barebone System Starting Asus PC Probe Asus PC ProbeFan Monitor Using Asus PC ProbeTemperature Monitor Monitor SummaryHard Drives SettingsHistory Fan ControlDevice Summary MemoryDMI Explorer Asus PC Probe Task Bar Icon