Asus P8H61-m2, si r2.0, tpm manual CPU and Chassis fan connectors 4-pin CPUFAN, 3-pin Chafan

Page 33

2.CPU and Chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN)

Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector.

CPU_FAN

P8H61-M2/TPM/SI R2.0

GND

CPU FAN PWR

CPU FAN IN

CPU FAN PWM

CHA_FAN

GND

+12V Rotation

P8H61-M2/TPM/SI R2.0 Fan connectors

DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors!

• The CPU_FAN connector supports a CPU fan of maximum 1A (12 W) fan power.

• Only the 4-pin CPU fan supports the ASUS Fan Xpert 2 feature.

3.Serial port connectors (10-1 pin COM1)

The connector is for a serial (COM) port. Connect the serial port module cable to the connector, then install the module to a slot opening at the back of the system chassis.

The serial port module is purchased separately.

COM1

CTS

DSR

DTR

RXD

PIN 1

DCD TXD GND RTS RI

P8H61-M2/TPM/SI R2.0

P8H61-M2/TPM/SI R2.0 Serial port (COM1) connector

Chapter 1: Product introduction

1-23

E7361_P8H61-M2-TPM-SI R2.0_Manua23 23

5/16/12 1:44:27 PM

Image 33

Contents Motherboard Offer to Provide Source Code of Certain Software Copyright 2012 ASUSTeK Computer INC. All Rights ReservedContents Software support Appendices Electrical safety Safety informationOperation safety About this guideConventions used in this guide Where to find more informationTypography Bold textP8H61-M2/TPM/SI R2.0 specifications summary USB E7361P8H61-M2-TPM-SI R2.0Manua10 16/12 14344 PM Package contents Special featuresWelcome Intel H61 Express Chipset Gigabit LAN solutionPCI Express Intel Smart Response Technology SSD Speed with HDD CapacityNetwork iControl Innovative Asus featuresAI Suite Asus Anti-Surge ProtectionGPU Boost Asus CrashFree BiosAsus Fan Xpert Asus MyLogo2Before you proceed Standby Power LEDPlacement direction Motherboard overviewScrew holes Motherboard layout Layout contentsTo install a CPU Locate the CPU socket on the motherboard Installing the CPUCentral Processing Unit CPU Load lever Retention tabPnP cap CPU notches Load plateGold MarkInsert the load lever under the retention tab Installing the CPU heatsink and fan P8H61-M2/TPM/SI R2.0 CPU fan connector Uninstalling the CPU heatsink and fanOverview System memoryDimm Memory configurationsDDR3-2200 O.C. MHz capability DDR3-2250 O.C. MHz capabilityDDR3-2133 O.C. MHz capability DDR3-2000 O.C. MHz capabilityDDR3-1600 O.C. MHz capability DDR3-1333 MHz capability IVY Bridge CPUDDR3-1333 MHz capability Sandy Bridge CPU DDR3-1066 MHz capability IVY Bridge CPU Following table shows how to use the Dimm slotsDDR3-1066 MHz capability Sandy Bridge CPU Sides SS Single-sided DS Double-sided Dimm supportRemoving a Dimm Installing a DimmTo remove a Dimm Outward to unlock the DimmExpansion slots Clear RTC RAM 3-pin Clrtc JumpersAudio 2, 4, 6, or 8-channel configuration ConnectorsRear panel ports LAN port LED indicationsATX power connectors 24-pin EATXPWR, 4-pin ATX12V Internal connectorsSerial port connectors 10-1 pin COM1 CPU and Chassis fan connectors 4-pin CPUFAN, 3-pin ChafanThis connector supports several chassis-mounted functions LPT connector 26-1 pin LPTReset button 2-pin Reset Hard disk drive activity LED 2-pin +HDLEDSerial ATA 3.0 Gb/s connectors 7-pin SATA3G1-4 Front panel audio connector 10-1 pin AafpConfiguration Sata Mode Selection USB 2.0 connectors 10-1 pin USB78, USB910 Speaker connector 4- pin Speaker480Mbps connection speed P8H61-M2/TPM/SI R2.0 Digital audio connector Digital audio connector 4-1 pin SpdifoutClick an item to install Installing an operating systemSoftware support Support DVD informationAsus Update utility Managing and updating your BiosInstalling Asus Update Updating the BiosAsus EZ Flash Select Update Bios from file, then click NextRecovering the Bios Asus CrashFree Bios 3 utilityAsus Bios Updater Before updating BiosBooting the system in DOS environment Bios Updater screen appears as below Updating the Bios fileBios menu screen Bios setup programEntering Bios Setup at startup Entering Bios Setup after PostEZ Mode Advanced Mode Menu barMenu bar on top of the screen has the following main items Menu items Configuration fieldsBack button Submenu itemsSystem Language English Main menuSystem Date Day xx/xx/xxxx System TimeUser Password Administrator PasswordAi Tweaker menu Asus MultiCore Enhancement EnabledMemory Frequency Auto GPU BoostDisabled Disables this function CPU Power ManagementDram Timing Control Decrease average heat productionTPM Support Disabled CPU ConfigurationIntel Adaptive Thermal Monitor Enabled Advanced menuExecute Disable Bit Enabled Limit Cpuid Maximum DisabledIntel Virtualization Technology Disabled Hardware Prefetcher EnabledPCH Configuration High Precision Timer EnabledIntelR Smart Connect Technology Isct Configuration Disabled System Agent Configuration Sata ConfigurationOnboard Devices Configuration USB Configuration8 APM Network Stack Monitor menu CPU Temperature / MB Temperature xxxºC/xxxºFCPU / Chassis Fan Speed xxxx RPM or Ignore / N/A CPU Voltage, 3.3V Voltage, 5V Voltage, 12V VoltageChassis Q-Fan Control Enabled CPU Q-Fan Control EnabledCPU temperature SilentChassis Upper Temperature 70ºC Anti Surge Support EnabledChassis Lower Temperature 40ºC Chassis Fan Max. Duty Cycle% 100%Bootup NumLock State On Boot menuFull Screen Logo Enabled Wait for ‘F1’ If Error EnabledSetup Mode EZ Mode Option ROM Messages Force BiosUEFI/Legacy Boot Enabled both Uefi and Legacy Boot Option PrioritiesAsus EZ Flash 2 Utility Tools menuAsus SPD Information Asus O.C. ProfileExit menu E7361P8H61-M2-TPM-SI R2.0Manua28 IC Canadian Compliance Statement Federal Communications Commission StatementCanadian Department of Communications Statement Asus Recycling/Takeback ServicesTelephone AddressOnline support Support faxDeclaration of Conformity