BenQ MX722 user manual Replacing the remote control batteries

Page 13

Replacing the remote control batteries

1.To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slide it up in the direction of the arrow as illustrated. The cover will slide off.

2.Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive

(+) goes to positive and negative (-) goes to negative.

3.Refit the cover by aligning it with the base and sliding it back down into position. Stop when it clicks into place.

•Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

•Replace only with the same or equivalent type recommended by the battery manufacturer.

•Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region.

•Never throw the batteries into a fire. There may be danger of an explosion.

•If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.

Introduction 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents MX722 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Projector exterior viewRear/lower side Projector Controls and functionsON/ OFF Remote control+/PAGE Operating the Laser pointer Remote control effective rangeMute TestReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsOffset Inch Max AverageConnection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector Device About the microphone inputStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signalChanging Color Space Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundUsing the teaching templates Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options Wall ColorSleep Timer System Setup BasicMin/30 min 12 hrStatus Main menu Sub-menu Options System Setup AdvancedIP Address Current System Status Description of each menu Temperature Picture ModeColor Temperature Fine Tuning 3D ColorInstallation TimerSearch Color SpaceFunction Description System Setup Basic menOperation RemoteAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkCurrent Information menu Function DescriptionSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp input Resolution Mode Frequency KHz MHzTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer
Related manuals
Manual 62 pages 17.56 Kb

MX722 specifications

The BenQ MX722 is a highly versatile and feature-rich projector designed for both educational and professional environments. With its advanced technologies and user-friendly features, it delivers exceptional performance and reliability.

One of the standout features of the BenQ MX722 is its impressive brightness of 4000 ANSI lumens. This high level of brightness ensures that presentations and videos are clear and vibrant, even in well-lit rooms. Coupled with a native XGA resolution of 1024x768 pixels, the projector produces sharp images with excellent detail, making it ideal for showcasing detailed content.

The MX722 utilizes DLP technology, which enhances image quality and reliability. DLP projectors are known for their ability to produce consistent color and contrast, which is vital for maintaining viewer engagement during presentations. The projector's 15,000:1 contrast ratio further enhances image quality by providing deeper blacks and brighter whites, ensuring that visuals are striking and impactful.

In terms of connectivity, the BenQ MX722 is equipped with a comprehensive range of ports, including HDMI, USB, and VGA inputs. This diverse range of connection options allows users to easily connect various devices, from laptops to media players, without the need for additional adapters. The projector also features a built-in speaker, which enhances the audio experience during presentations without requiring external sound systems.

User-friendliness is another hallmark of the MX722. The projector is designed with a simple interface, making it easy to navigate settings and adjust parameters. It also features an automatic vertical keystone correction function, which helps to maintain image integrity even when the projector is not perfectly aligned with the screen.

In addition to its performance features, the BenQ MX722 is designed with energy efficiency in mind. It incorporates eco-friendly technologies that reduce power consumption, making it a cost-effective option for long-term use. The projector also has a long lamp life of up to 10,000 hours in Eco Mode, which minimizes maintenance costs and downtime.

Overall, the BenQ MX722 stands out as a reliable and high-performing projector suited for various professional and educational needs. With its robust features, impressive image quality, and user-friendly design, it provides an exceptional tool for presentations, lectures, and multimedia sharing.
Top Page Image Contents