BenQ MX722 user manual Timing of replacing the lamp, Status Message

Page 50

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 54 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

 

 

Install a new lamp for optimal performance. If the

Notice

projector is normally run with Economic

 

selected (See "Getting to know the lamp hour" on

Order Replacement Lamp

page 49), you may continue to operate the

Lamp>XXXX Hours

projector until the next hour lamp warning

 

appears.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

 

It is strongly recommended that you replace the

Notice

lamp at this age. The lamp is a consumable item.

 

The lamp brightness diminishes with use. This is

Replace Lamp Soon

normal lamp behavior. You can replace the lamp

 

whenever you notice that the brightness level has

Lamp>XXXX Hours

 

significantly diminished.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

Notice

 

Replace Lamp Now

 

Lamp>XXXX Hours

 

Lamp usage time exceeded

 

Order a new lamp at lamp.benq.com

 

OK

 

 

The lamp MUST be replaced before the projector

WARNING

will operate normally.

Out of Lamp Usage Time

Press MODE/ENTER to dismiss the message.

 

 

Replace lamp (refer to User Manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

50 Maintenance

Page 49 Page 51
Image 50
Page 49 Page 51
Contents
MX722 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Projector+/PAGE Remote controlON/ OFF Mute Remote control effective rangeOperating the Laser pointer TestReplacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingOffset Projection dimensionsObtaining a preferred projected image size Inch Max AverageConnection ConnectionPlaying sound through the projector Connecting video source devicesConnecting audio About the microphone input DeviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Changing Color Space Switching input signalDisabling the password function Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Setting a preferred color temperature 3D Color ManagementSelection Description Setting the presentation timerResetting current or all picture modes Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound Using the test patternUsing the teaching templates Direct power off Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Wall ColorMin/30 min System Setup BasicSleep Timer 12 hrIP Address Main menu Sub-menu Options System Setup AdvancedStatus Current System Status Description of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D ColorSearch TimerInstallation Color SpaceOperation System Setup Basic menFunction Description RemoteAudio System Setup Advanced menu Function Description HighAltitude Lamp Standby System Setup Advanced menu Function Description Reset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationKHz Timing chartSupported timing for PC input Resolution Mode Frequency KHz MHz Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput TimingSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer
Related manuals
Manual 62 pages 17.56 Kb
Top Page Image Contents