Axis Communications Q7424-R manual LED indicators, Function Pin, Color Indication

Page 16

Page 16

AXIS Q7424-R Installation Guide

RS-485/RS-422 connector - Two 2-pin terminal blocks for RS-485/RS-422 serial interface used to control auxiliary equipment, e.g. PTZ devices.

The RS-485/RS-422 serial port can be configured to support:

RS-485/422

• Two-wire RS-485 half duplex

• Four-wire RS-485 full duplex

• Two-wire RS-422 simplex

• Four-wire RS-422 full duplex point to point communication

RX/TX

TX

1

2

3

4

A

B

A

B

Function

Pin

Notes

RS-485/RS-422 RX/TX A

1

(RX) For full duplex RS-485/RS-422

(RX/TX) For half duplex RS-485

RS-485/RS-422 RX/TX B

2

RS-485/RS-422 TX A

3

(TX) For full duplex RS-485/RS-422

RS-485/RS-422 TX B

4

Note: Connect the signals according to the letters on the terminal block and the description in the image above; then turn the connector 180° and plug into the unit.

SD memory card slot - The SD memory card can be used for local recording with removable storage.

BNC connector - Connect a 75 ohm coaxial video cable (max. length 800 feet (250 meters)).

Note: For each video input 75 Ohm video termination can be enabled/disabled via the product's web page from Setup > Video & Audio > Video (1, 2, 3, or 4) > Camera Settings. These terminations are enabled on factory default. In cases where the product is to be connected in parallel with other equipment, for optimum video quality, it is recommended that termination be enabled for only the last device in the video signal chain.

LED indicators

LED	Color	Indication

Network	Green	Steady for connection to a 1 Gbit/s network. Flashes for network activity.

	Amber	Steady for connection to 10/100 Mbit/s network. Flashes for network activity.

	Unlit	No network connection.

Status	Green	Steady green for normal operation.

	Amber	Steady during startup, during reset to factory default or when restoring settings.

	Red	Flash for failed upgrade.

Power	Green	Normal operation.

	Amber	Flashes green/amber during firmware upgrade.

Image 16

Contents Installation Guide Axis Q7424-R Video EncoderAbout this Document Korea Safeguards Battery replacementPage Axis Q7424-R Video Encoder Installation Guide Package contentsDimensions Hardware overviewFront view Axis Q7424-RMount the video encoder Install the hardwareConnect the cables and insert the SD memory card Assign an IP address Method Recommended forAutomatic discovery Axis IP Utility single camera/small installationSet the IP address manually optional Assign an IP address in a single device Axis Camera Management multiple cameras/large installationsAssign IP addresses in multiple devices Set the password Click the Create self-signed certificate buttonAxis Q7424-R Installation Guide Other methods of setting the IP address Set the IP address with ARP/PingUnit connectors Audio in/outFunction Function Pin SpecificationsDescription Function Pin LED indicatorsColor Indication Resetting to the factory default settings Accessing the Axis Q7424-R from the InternetFurther information TipRemplacement des piles Mesures de sécuritéÉtapes d’installation Axis Q7424-R Guide dinstallationContenu de l’emballage Élément Modèles/variantes/remarquesVue de face Aperçu du matérielVue arrière Installation du matériel Montage de l’encodeur vidéoBranchez les câbles et insérez la carte mémoire SD RemarquesMéthode Recommandée pour Système ’exploitation Attribution d’une adresse IPDétection automatique Axis IP Utility une seule caméra/petite installationDéfinir manuellement l’adresse IP optionnel Attribuer une adresse IP à un seul dispositif Attribution dadresses IP à plusieurs périphériquesConfigurer le mot de passe Remarques Autres méthodes de définition de l’adresse IP Définition de ladresse IP à laide dARP/PingConnecteurs de lunité Fonction Axis Q7424-R Guide dinstallation Entrée/Sortie audioDescription Broche Fonction Broche Remarques Charge maximale = 100 mARX/TX TX Voyants DEL Voyant DEL Couleur IndicationRétablissement des paramètres dusine par défaut Accès à l’AXIS Q7424-R sur InternetPlus d’informations ConseilSicherheitsvorkehrungen VorsichtInstallationsschritte Axis Q7424-R InstallationsanleitungInhalt des Produktpakets WichtigHardwareübersicht AbmessungenSeite VorderansichtInstallation der Hardware Befestigen des Video-EncodersAnschließen der Kabel und Einschieben der SD-Speicherkarte HinweiseZuweisen einer IP-Adresse Methode Empfohlen für BetriebssystemAutomatische Erkennung Axis IP Utility Einzelne Kamera/kleine InstallationenManuelle Zuweisung der IP-Adresse optional Zuweisen einer IP-Adresse für ein einzelnes Gerät Axis Camera Management mehrere Kameras/große InstallationenZuweisen von IP-Adressen für mehrere Geräte Festlegen des Kennworts Hinweise Admin-Seiten des DHCP-Servers Andere Methoden zum Festlegen der IP-AdresseZuweisen der IP-Adresse per ARP/Ping HinweiseSeite Geräteanschlüsse Audio-Ein-/Ausgang Funktion Kontakt Beschreibung NummerFunktion Kontakt Hinweise Spezifikationen FunktionLED-Anzeigen Farbe BedeutungWeitere Informationen Über das Internet auf den Axis Q7424-R zugreifenTipp Precauzioni AttenzioneProcedura di installazione Guida allinstallazione di Axis Q7424-RContenuto della confezione ImportanteDimensioni Panoramica dell’hardwarePagina Vista anterioreMontaggio del codificatore video Installazione dellhardwareCollegare i cavi e inserire la scheda di memoria SD Assegnazione di un indirizzo IP Metodo Consigliato perRilevamento automatico Axis IP Utility Telecamera singola/piccola installazioneAssegnazione manuale dell’indirizzo IP facoltativa Assegnazione di un indirizzo IP a un singolo dispositivo Axis Camera Management più telecamere/grandi installazioniAssegnazione degli indirizzi IP a più dispositivi Impostazione della password Pagina Altri metodi di assegnazione dell’indirizzo IP Assegnazione dellindirizzo IP con ARP/PingPagina Connettori Ingresso/uscita audioFunzione Numero Descrizione Pin Funzione Pin SpecificheFunzione Pin Indicatori LED Colore IndicazioneUlteriori informazioni Ripristino delle impostazioni predefiniteSuggerimento Medidas preventivas ¡PRECAUCIÓNContenido del paquete Pasos para la instalaciónGuía de instalación del Axis Q7424-R ¡ImportanteDimensiones Presentación del hardwarePágina Vista frontalMontaje del codificador de vídeo Instalación del hardwareNotas Asignación de la dirección IP Método Recomendado paraConfiguración manual de la dirección IP opcional Detección automáticaAsignación de una dirección IP en un dispositivo individual Asignación de direcciones IP en varios dispositivosConfiguración de la contraseña Notas Otros métodos para configurar la dirección IP Configuración de la dirección IP con ARP/PingConectores Función Entrada/salida de audioDescripción Función Pin Notas Especificaciones Función Pin NotasIndicadores LED Color IndicaciónRestablecimiento de los valores iniciales Acceso al codificador Axis Q7424-R desde InternetMás información Un consejoPage Ver