Enterasys Networks 4H4202-72 manual Preparation, Installing Module into Matrix E7 or N7 Chassis

Page 36

Installing Module into a Chassis

Preparation

1.Remove the blank panel covering the slot in which the module will be installed. All other slots must remain covered to ensure proper airflow for cooling. (Save the blank plate in the event you need to remove the module.)

2.Remove the module from the shipping box. (Save the box and packing materials in the event the module needs to be reshipped.)

3.Locate the antistatic wrist strap shipped with the chassis. Attach the antistatic wrist strap to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding receptacle at the upper right corner of the chassis.

4.Remove the module from the plastic bag. (Save the bag in the event the module must be reshipped.) Observe all precautions to prevent damage from Electrostatic Discharge (ESD).

5.Examine the module for damage. If any damage exists, DO NOT install the module. Immediately contact Enterasys Networks. Refer to “Getting Help” on page xviii.

Installing Module into Matrix E7 or N7 Chassis

To install the module, refer to Figure 3‐2 and proceed as follows:

Caution: To prevent damaging the backplane connectors in the following step, take care that the module slides in straight and properly engages the backplane connectors.

Ensure that the top lever lines up with the desired slot number located on the front panel of the chassis. Refer to Figure 3-2.

Precaución: Para evitar que se dañen los conectores del panel posterior en el siguiente paso, intente deslizar el módulo en forma recta y verifique que se enganche correctamente en los conectores de panel posterior.

Asegúrese de que la palanca superior esté alineada con respecto al número de ranura correspondiente ubicado en el panel frontal del chasis. Consulte en Figure 3-2.

1.Locate the chassis card guides that line up with the slot number in which the module will be installed. (In this example, slot 1 is being used.) Make sure the module locking levers are in the open position (top and bottom).

3-6 Installation

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Troubleshooting Appendix a SpecificationsIndex Figures Contents of DFE-Gold Module Carton TablesAbout This Guide Who Should Use This GuideImportant Notice How to Use This Guide Related DocumentsFor Refer to Conventions Used in This Guide Following conventions are used in this guideGetting Help Introduction Overview of DFE-Gold Series CapabilitiesDFE-Gold Modules 4H4282-494H4283-49 4H4203-72 4H4202-724H4284-49 DFE 4H4202-72 and 4H4284-49 DFE-Gold Modules Connectivity Switch Configuration Using WebView Switch Configuration Using CLI CommandsManagement Standards CompatibilityLanview Diagnostic LEDs Network Requirements 10BASE-T Network100BASE-TX Network 100BASE-FX Fiber-Optic NetworkInstallation Installation Site Requirement Contents of DFE-Gold Module Carton QuantityUnpacking the DFE-Gold Module Installing Optional Network Expansion Module DFE Module Placement and Installation RulesExample 1 -1, a Example 2 -1, BInstalling Module into a Chassis Example 3 -1, CExample 4 -1, D Installing Module into Matrix E7 or N7 Chassis PreparationInstalling Module into a Chassis ➆ ➁ Installing Module into Matrix N1, N3, or N5 Chassis Connecting to the Network Connecting to the NetworkConnecting UTP Cables to 4H4282-49 or 4H4202-72 Connecting a Twisted Pair Segment With RJ45 Connector RX+ TX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting UTP Cables to 4H4283-49 or 4H4203-72 Connecting a Twisted Pair Using RJ21 Straight Connector 10 Connection Using Optional RJ21 Angle Adapter Connecting Fiber-Optic Cables to 4H4284-49 COM Mgmt CPU Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Parameter SettingConnecting to a VT Series Terminal 12 Connecting an IBM PC or CompatibleConnecting to a Modem 13 Connecting a VT Series Terminal14 Connecting to a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation Completing the Installation of a New SystemModem Port Adapter Wiring and Signal Diagram RJ45 DB25 First-Time Log-In Using a Console Port Connection 15 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account EnterCompleting the Installation Troubleshooting Using LanviewAbout the Management Mgmt LED Lanview LEDs on 4H4282-49, 4H4283-49, and 4H4203-72 Viewing Receive/Transmit Activity on 4H4202-72 Lanview LEDs on 4H4202-72Viewing the Receive and Transmit Activity on 4H4284-49 Lanview LEDs on 4H4284-49Lanview LEDs Color State Recommended ActionLED Troubleshooting Checklist Refer to the Enterasys Matrix DFE-Gold SeriesEnterasys Matrix DFE-Gold Series Configuration Overview of DFE-Gold Module Shutdown Procedure OFFLINE/RESET SwitchRecommended Shutdown Procedure Using OFFLINE/RESET Switch Last Resort Shutdown Procedure Using OFFLINE/RESET SwitchSpecifications DFE-Gold Module SpecificationsTable A-1 Specifications Chassis Backplane Connectivity Table A-2 COM Port Pin Assignments Signal Name Input/Output COM Port Pinout AssignmentsRegulatory Compliance Table A-3 Compliance Standards Regulatory ComplianceMode Switch Bank Settings Optional Installations Required ToolsSetting the Mode Switches Figure B-1 Mode Switch Location on 4H4282-49 and 4H4283-49 Figure B-3 Mode Switch Location on 4H4202-72 Memory Locations and Replacement Procedures Location of Dimm and Dram Simm Memory ModulesFigure B-6 Dimm and Dram Simm Locations 4H4203-72 Dimm Replacement Procedure 4H4282-49 and 4H4283-49 Removing the Dram SimmInstalling the Dram Simm on 4H4282-49 or 4H4283-49 Removing the Dram Simm from 4H4203-72 Installing the Dram Simm on 4H4203-72 Figure B-11 Removing Existing Dram Simm from 4H4203-72Dram Simm Replacement 4H4202-72 Figure B-12 Installing the Dram Simm on 4H4203-72Dimm Replacement Procedure All DFE Modules Removing the DimmInstalling the Dimm Figure B-14 Installing the DimmPage Index NumericsOFFLINE/RESET button 4-10Optional network expansion module
Related manuals
Manual 90 pages 58.47 Kb

4H4203-72, 4H4283-49, 4H4282-49, 4H4202-72, 4H4284-49 specifications

Enterasys Networks has long been a leader in providing robust networking solutions for enterprises, and their range of products, including models 4H4284-49, 4H4202-72, 4H4282-49, 4H4283-49, and 4H4203-72, exemplifies their commitment to delivering high-performance networking equipment. These models are designed to meet the increasing demands of modern network environments, ensuring scalability, reliability, and security.

One of the standout features of the Enterasys Networks products is their advanced Layer 2 and Layer 3 switching capabilities. This allows for efficient data transmission and fundamental network routing processes, making them ideal for both small business networks and large enterprise setups. The models boast high throughput rates and low latency, which are essential for applications requiring real-time data transfer, such as video conferencing and VoIP.

Additionally, these switches are equipped with Power over Ethernet (PoE) functionality, enabling users to power devices like IP phones, wireless access points, and security cameras directly from the switch. This eliminates the need for additional electrical wiring, simplifying installation and reducing costs. The power budget is adequately managed, ensuring that all connected devices operate efficiently.

In terms of security, Enterasys Networks has integrated advanced features such as VLAN support and Access Control Lists (ACLs) to enhance network segmentation and safeguard against unauthorized access. This is particularly crucial in environments where sensitive data is handled. The inclusion of network monitoring and management tools further aids IT teams in maintaining optimal network performance and detecting potential issues proactively.

Moreover, these models support a variety of networking protocols, which adds flexibility and compatibility with existing infrastructure. The user-friendly web interface and CLI enable easy configuration and management, catering to network administrators' diverse levels of expertise.

Built with high-quality materials, Enterasys Networks devices are designed to withstand the rigors of a data center environment, ensuring longevity and reliable performance. The combination of these features makes the 4H4284-49, 4H4202-72, 4H4282-49, 4H4283-49, and 4H4203-72 models excellent choices for organizations looking to enhance their networking capabilities and ensure a secure, efficient communication network that can grow with their needs. Overall, Enterasys Networks continues to set benchmarks in networking technology, making significant strides in improving connectivity and performance for enterprises worldwide.
Top Page Image Contents