Black Box Pro Switching System 4 Network Backup Switches, NBS008A manual

Page 19

Chapter 5: Operation

Table 5-1. RS-232 Controller Card response to “help” command (1200, N, 8, 1).

Rack 1 switch Rev A Commands: get system

get rack n (n = rack addr, 1 to 255) get port y (y = port addr, 1 to 4080) get version n (n = rack addr, 1 to 255) set system X (X = A or B)

set rack n X (n = rack addr, 1 to 255, X = A or B) set port y X (y = port addr, 1 to 4080, X = A or B) help (displays current commands)

SPACE (space character starts terminal mode) exit (exit terminal mode)

>

NOTE: For commands that use a rack address “n,” refer to Section 3 for information on how to set the rack address DIP switch SW2. Each rack can contain up to 16 ports. Rack 1 is assigned port numbers 1 through 16, rack 2 is assigned port numbers 17 through 32, and so on. For commands that use a port address “y”, use the following formula to determine the port address of any port in any rack: y = 16*(rack address – 1) + port#

Example: Port 12 in rack 3 has port address 44.

Commands are not case sensitive and can be entered as either upper or lower case. The terminal interface echoes each character it receives back to your terminal, allowing the user to backspace to correct typing errors. Each word on a command line must be separated by a single SPACE character. The command is processed when you press the ENTER KEY. All of the above commands except “help” and “exit” may be abbreviated by using only the first character of each word on the command line. For example:

“g s<CR>” is the same as “get system<CR>”.

“s r 2 A<CR>” is the same as “set rack 2 A<CR>”.

Table 5-2 shows an example of each command along with the expected Response and Action.

NOTE: Each command must be followed by a carriage return (ASCII HEX 0x0D).

 

 

 

Table 5-2. Commands.

 

 

 

 

 

 

 

 

 

Command

Response

Switch Action

 

 

 

 

 

 

 

 

“SPACE” character

>

Starts terminal mode if not started (1200, N, 8, 1); otherwise, will echo back a “SPACE” character if

 

already in terminal mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

get system

System status (A or B)

No switching action taken.

 

 

 

 

 

 

 

 

 

set system A

System set to A

All COMMON ports in system will be connected to their respective A ports.

 

 

 

 

 

 

 

 

 

set system B

System set to B

All COMMON ports in system will be connected to their respective B ports.

 

 

 

 

 

 

 

 

 

Rack 1 status

No switching action taken. In the response shown, Ports 1–4 are in A, 5–8 are in B, and the rest are

 

get rack 1

AAAABBBBXXXXXXXX

not present. If the selected rack doesn’t respond within 3 seconds, Rack 1 will reply with “No

 

 

 

Response.”

 

 

 

 

 

 

 

 

 

set rack 1 A

Rack 1 set to A

All COMMON ports in rack 1 wil be connected to their respective A ports.

 

 

 

 

 

 

 

 

 

set rack 1 B

Switches respond “Rack 1 set to B”

All COMMON ports in rack 1 wil be connected to their respective B ports.

 

 

 

 

 

 

 

 

 

get port 8

Port 8 status (A, B, or empty)

No switching action taken.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NBS008A

724-746-5500 blackbox.com

Page 19

 

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Pro Switching System 4 Network Backup Switches Trademarks Used in this Manual Trademarks Used in this ManualFCC and IC RFI Statements NOM Statement Table of Contents Specifications SpecificationsOverview Introduction OverviewWhat’s Included Available ModelsNBS008MA, NBSALL8, NBSALL8MGR, NBS016A, NBS016MA Hardware DescriptionBack panel components 16 17 Front Panel of NBS004A, NBS004MANBS006A, NBS006MA NBS006A, NBS006MA front panel components Front Panel of NBS006A, NBS006MAFront Panel of NBS008A, NBS008MA, NBSALL8, NBSALL8MGR Front Panel of NBS016A, NBS016MA Configuration ConfigurationDIP switch SW1 and SW2 settings RJ-11 GANG-OUT port pin assignment Installation InstallationOperation Manual SwitchingOperation Example Port 12 in rack 3 has port address Background Programming Tips for Using the RS-232 Terminal CommandsProgramming Getset Pingreply ON/OFF Getset Snmpenable ON/OFF R6000 Console CommandsGetset Alerttype TRAP/SYSLOG Getset Monitormac X X X X X X X = HEX CharsAuto failover and manual recovery Operation Ethernet Network Interface Setup Ethernet Network Interface Setup GET Version Console CommandsConsole Commands GET ALLSET Rack N AB GET Power NSET System AB GET Rack NSET Ipaddress GET Ipaddress SET Snmpenable Onoff GET SnmpenableSET Webenable Onoff GET Webenable GET WebpasswordGET Telnettimeout GET WebtimeoutSET Telnetenable Onoff GET Telnetenable GET TelnetpasswordSET Monitorfailcount N GET Monitorfailcount SET Authenticationtrap Onoff GET AuthenticationtrapSET Monitormac X X X X X GET Monitormac SET Monitorinterval N GET MonitorintervalSET Manager N SET Adminip NGET Adminip N GET AlerttypeGetset Webenable ON/OFF ResetSET Defaults R6000 Console Commands GETRestart use after Save Save settings for next startupSET Web Interface Web InterfaceWeb Interface MIB Path Summary and Trap Definitions MIB Path Summary and Trap DefinitionsAbRackKeyStat-1.3.6.1.4.1.9477.1.4.2.1.3.RackIndex AbRackGangPort-1.3.6.1.4.1.9477.1.4.2.1.2.RackIndexMIB Path Summary and Trap Definitions MIB Path Summary and Trap Definitions Syslog Messages Syslog MessagesSyslog Messages Blackbox.com Black Box Tech Support FREE! Live /7

NBS008A, Pro Switching System 4 Network Backup Switches specifications

The Black Box Pro Switching System 4 Network Backup Switches, specifically the NBS008A model, represents a cutting-edge solution for network resilience and management. This advanced device is designed to enhance network reliability by providing a seamless way to switch between primary and backup network links, ensuring continuous connectivity for critical applications.

One of the standout features of the NBS008A is its automatic failover capability. In the event of a link failure, the system swiftly transitions to a secondary connection without requiring manual intervention. This is crucial for businesses that rely on uptime, as it minimizes downtime and ensures that operations remain uninterrupted.

The device also supports a variety of network protocols, making it versatile for different network environments. It is compatible with Ethernet and other common standards, providing flexibility for integration into existing infrastructure. The NBS008A is equipped with multiple ports, allowing for connection to various devices and networks, and enabling redundancy across critical pathways.

In terms of management, the Black Box Pro Switching System features an intuitive user interface. Administrators can easily monitor the status of all connected links, configure settings, and access diagnostic tools to troubleshoot issues. This ease of use is essential for maintaining optimal network performance and quickly identifying any potential problems.

Moreover, the NBS008A incorporates advanced security features. It supports encryption and authentication protocols that protect against unauthorized access, ensuring that sensitive data is safeguarded during transmission. This security aspect is particularly important in today’s environment, where cyber threats are prevalent and organizations must prioritize data integrity.

The build quality of the NBS008A is robust, designed to withstand harsh operational conditions while maintaining high performance. Its compact form factor and rack-mountable design make it an efficient choice for various settings, whether in a data center or a smaller office environment.

Additionally, the NBS008A supports various network speeds, accommodating both legacy systems and modern high-speed networks. With its rich feature set, robust security measures, and reliable performance, the Black Box Pro Switching System 4 Network Backup Switches, NBS008A, is an invaluable asset for organizations seeking to enhance their network's reliability and efficiency.
Top Page Image Contents