Black Box Essential Console Commands for NBS008A Network Backup Switches

Page 32

Chapter 7: Console Commands

GET ALERTTYPE

Set or display the type of alert messages sent by the switch when certain events such as a change in switch state occur. The switch can be configured to issue either syslog messages, or SNMP traps.

NOTE: At least one IP address must be entered using the “SET MANAGER N X.X.X.X” command before either syslog messages or traps will be issued. See Chapter 9 for a list of the traps supported by the switch, and see Chapter 10 for a list of the supported syslog messages.

SET ADMINIP N X.X.X.X

Set administrator N (1-8) IP address. Up to 8 different administrator IP addresses can be entered. To remove an entry from the list, set the IP address to 0.0.0.0. If all 8 ADMIN IP addresses are 0.0.0.0 (no ADMIN IP addresses are configured) the switch will allow access via the Ethernet network management interface from any IP address, subject to the existing password and enable flags for each interface. If one or more ADMIN IP addresses are nonzero, the switch will only process messages received from the configured (non-zero) ADMIN IP addresses. All other messages will be ignored. This ADMIN IP address filtering feature applies to the telnet, Web browser, and SNMP Ethernet interfaces and to the PING reply functions. The ADMIN IP address filtering does not affect outgoing PING and ARP messages so the switch is still able to monitor any IP address for the “auto-switch” features. The administrator IP addresses can be different than the manager IP addresses. Any change will not become permanent until a SAVE operation is performed.

GET ADMINIP N

Display the IP address of administrator N (1–8). If no value is entered for “N,” then all administrator IP addresses will be displayed.

ADMIN IP Addresses:

1:192.168.1.113

2:192.168.1.115

3:192.168.1.149

4:192.168.1.100

SET MANAGER N X.X.X.X

Set SNMP manager N (1–16) IP address. Up to 16 SNMP MANAGER IP addresses can be entered for destinations of trap or syslog messages. Trap or syslog messages will be sent to all enabled MANAGER IP addresses. To remove an entry from the list, set the IP address to 0.0.0.0.

SNMP Manager Table:

1:192.168.1.113

2:192.168.1.115

3:192.168.1.149

4:192.168.1.100

GET MANAGER N

Display SNMP manager N (1–16) IP address.

GET MANAGER

Display all SNMP manager IP addresses.

PING X.X.X.X

Causes the switch to issue a single ICMP echo request packet to the designated IP address. If a response is received, the switch will display the message “Reply from X.X.X.X”. If no response is received within 5 seconds, the switch will display the message “Request timed out.”

Page 32

724-746-5500 blackbox.com

NBS008A

Image 32
Contents Pro Switching System 4 Network Backup Switches Trademarks Used in this Manual Trademarks Used in this ManualFCC and IC RFI Statements NOM Statement Table of Contents Specifications SpecificationsOverview Overview IntroductionAvailable Models What’s IncludedBack panel components Hardware DescriptionNBS008MA, NBSALL8, NBSALL8MGR, NBS016A, NBS016MA Front Panel of NBS004A, NBS004MA 16 17Front Panel of NBS006A, NBS006MA NBS006A, NBS006MA NBS006A, NBS006MA front panel componentsFront Panel of NBS008A, NBS008MA, NBSALL8, NBSALL8MGR Front Panel of NBS016A, NBS016MA Configuration ConfigurationDIP switch SW1 and SW2 settings RJ-11 GANG-OUT port pin assignment Installation InstallationOperation Manual SwitchingOperation Example Port 12 in rack 3 has port address Programming Programming Tips for Using the RS-232 Terminal CommandsBackground R6000 Console Commands Getset Pingreply ON/OFF Getset Snmpenable ON/OFFGetset Monitormac X X X X X X X = HEX Chars Getset Alerttype TRAP/SYSLOGAuto failover and manual recovery Operation Ethernet Network Interface Setup Ethernet Network Interface Setup Console Commands Console CommandsGET ALL GET VersionGET Power N SET System ABGET Rack N SET Rack N ABSET Snmpenable Onoff GET Snmpenable SET Webenable Onoff GET WebenableGET Webpassword SET Ipaddress GET IpaddressGET Webtimeout SET Telnetenable Onoff GET TelnetenableGET Telnetpassword GET TelnettimeoutSET Authenticationtrap Onoff GET Authenticationtrap SET Monitormac X X X X X GET MonitormacSET Monitorinterval N GET Monitorinterval SET Monitorfailcount N GET MonitorfailcountSET Adminip N GET Adminip NGET Alerttype SET Manager NReset SET DefaultsR6000 Console Commands GET Getset Webenable ON/OFFSET Save settings for next startupRestart use after Save Web Interface Web InterfaceWeb Interface MIB Path Summary and Trap Definitions MIB Path Summary and Trap DefinitionsAbRackGangPort-1.3.6.1.4.1.9477.1.4.2.1.2.RackIndex AbRackKeyStat-1.3.6.1.4.1.9477.1.4.2.1.3.RackIndexMIB Path Summary and Trap Definitions MIB Path Summary and Trap Definitions Syslog Messages Syslog MessagesSyslog Messages Blackbox.com Black Box Tech Support FREE! Live /7

NBS008A, Pro Switching System 4 Network Backup Switches specifications

The Black Box Pro Switching System 4 Network Backup Switches, specifically the NBS008A model, represents a cutting-edge solution for network resilience and management. This advanced device is designed to enhance network reliability by providing a seamless way to switch between primary and backup network links, ensuring continuous connectivity for critical applications.

One of the standout features of the NBS008A is its automatic failover capability. In the event of a link failure, the system swiftly transitions to a secondary connection without requiring manual intervention. This is crucial for businesses that rely on uptime, as it minimizes downtime and ensures that operations remain uninterrupted.

The device also supports a variety of network protocols, making it versatile for different network environments. It is compatible with Ethernet and other common standards, providing flexibility for integration into existing infrastructure. The NBS008A is equipped with multiple ports, allowing for connection to various devices and networks, and enabling redundancy across critical pathways.

In terms of management, the Black Box Pro Switching System features an intuitive user interface. Administrators can easily monitor the status of all connected links, configure settings, and access diagnostic tools to troubleshoot issues. This ease of use is essential for maintaining optimal network performance and quickly identifying any potential problems.

Moreover, the NBS008A incorporates advanced security features. It supports encryption and authentication protocols that protect against unauthorized access, ensuring that sensitive data is safeguarded during transmission. This security aspect is particularly important in today’s environment, where cyber threats are prevalent and organizations must prioritize data integrity.

The build quality of the NBS008A is robust, designed to withstand harsh operational conditions while maintaining high performance. Its compact form factor and rack-mountable design make it an efficient choice for various settings, whether in a data center or a smaller office environment.

Additionally, the NBS008A supports various network speeds, accommodating both legacy systems and modern high-speed networks. With its rich feature set, robust security measures, and reliable performance, the Black Box Pro Switching System 4 Network Backup Switches, NBS008A, is an invaluable asset for organizations seeking to enhance their network's reliability and efficiency.