Samsung ML-4050 Series Using manual feed mode, Tips on using the multi-purpose tray

Page 34

4Squeeze the multi-purpose tray paper width guides and adjust them to the width of the paper. Do not force too much, or the paper will be bent, which will result in a paper jam or skew.

5When you print a document, set the paper source and type in the software application. See the Software section.

For information about setting the paper source and type on the control panel, see page 2.3.

6After printing, put the multi-purpose tray extension back to its place and close the multi-purpose tray.

Tips on using the multi-purpose tray

•Load only one size of print media at a time in the multi-purpose tray.

•To prevent paper jams, do not add paper when there is still paper in the multi-purpose tray. This also applies to other tray.

•Print media should be loaded face up with the top edge going into the multi-purpose tray first and be placed in the center of the tray.

•Always load only the print media specified in page 5.2 to avoid paper jams and print quality problems.

•Flatten any curl on postcards, envelopes, and labels before loading them into the multi-purpose tray.

•When you print on 76 mm x 127 mm (3 x 5 inches) sized media on the multi-purpose tray, open the rear cover for straight paper path to avoid paper jams.

•When you print on transparencies, open the rear cover. If not they may tear while exiting the printer.

Using manual feed mode

You can manually load a sheet of print media in the multi-purpose tray if you select Manual Feed in the Source option from the Paper tab when you change print settings to print a document. See the Software section. Manually loading paper can be helpful when you want to check the print quality after each page is printed.

This loading procedure is almost the same as the procedure for loading in the multi-purpose tray, except you load paper sheet-by-sheet in the tray, send print data to print the first page, and press Stop on the control panel to print each following page.

1 Load the paper with the side to be printed on facing up.

2Squeeze the multi-purpose tray paper width guides and adjust them to the width of the paper. Do not force too much, or the paper will be bent, which will result in a paper jam or skew.

3When you print a document, set the paper source to Manual Feed and select the appropriate paper size and type in the software application. See the Software section.

4Print a document.

The display shows a message prompting you to load paper and press Stop.

5Press Stop.

The printer picks up the print media and prints. After one page is printed, the message appears again.

Note

• If you do not press the button, after a pause the printer will automatically pick the print media.

6Insert the next sheet into the multi-purpose tray and press Stop. Repeat this step for every page to be printed.

5.7 <Loading print media>

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Page Page Contact Samsung Worldwide Country Customer Care Center Web SiteContents Installing accessories TroubleshootingSpecifications Environmental and Safety Consideration Safety and Regulatory InformationImportant Precautions and Safety Information Laser Safety StatementRecycling Ozone SafetyPower Saver Radio Frequency EmissionsUnited States of America Declaration of Conformity European CountriesRegulatory Compliance Statements Wireless GuidanceReplacing the Fitted Plug for UK Only EU D e c la ra tio n o f Co n fo rm ity R & T T E Introduction Special featuresSoftware section 2003/Vista You can print in Windows 98/Me/NT 4.0/2000/XPMacintosh Printer overview Front viewFinding more information Control panel overviewSelecting a location Clearance spaceUsing control panel menus System setupAccessing control panel menus Job manager menu Menu overviewInformation menu Layout menu Paper menuSystem Setup menu Graphic menuEmulation menu PostScriptPrinting a demo Using toner save modeChanging the display language Software overview Supplied softwareSystem requirements Printer driver featuresWindows Macintosh LinuxRequirements Via network administration programs Network setupVia the control panel Dynamic addressing BOOTP/DHCP Configuring TCP/IPConfiguring EtherTalk Supported operating systemsRestoring the network configuration Configuring IPX frame typesSetting Ethernet speed Printing a network configurationLoading print media Selecting print mediaSupported sizes of paper Type Size Dimensions Weighta CapacitybType Size Weight Print media for duplex printingGuidelines for special print media Guidelines for selecting and storing print mediaMedia type Guidelines Loading paper Using the standard tray or the optional trays Changing the size of the paper in the trayUsing the multi-purpose tray Load the paper with the side to be printed on facing upUsing manual feed mode Tips on using the multi-purpose trayPrinting to the output tray Face down Selecting an output locationPrinting to the rear cover Face up Basic printing Canceling a print jobPrinting a document Canceling a print job Printing a documentAccessories Ordering supplies and accessoriesToner cartridges How to purchase Cleaning the outside of the printer MaintenanceCleaning the printer Cleaning the inside of the printerPTL lens Maintaining the toner cartridge Checking the remaining tonerRedistributing toner cartridge Replacing the toner cartridge Clearing the Toner Low Replace Toner message Maintenance partsItems Yield Average Troubleshooting Clearing paper jamsTray Paper feed areaOptional tray Around the toner cartridge Multi-purpose trayDuplex unit area Paper exit areaDuplex jam Condition Suggested solutions Troubleshooting checklistTips for avoiding paper jams Understanding the status LED Understanding display messagesLSU Motor Error Message Meaning Suggested solutions LoadLow Heat Error OPC is CleaningToner cartridge-related messages Solving general printing problems Click the Samsung ML-4050 Settings and Printers. RightSpool Settings button Series PCL 6 printer iconSolving print quality problems Repetitive Condition Suggested solutions VerticalCondition Suggested solutions Curl or wave DefectsCommon Windows problems Common PostScript problemsInstallable Options section to Common Linux problemsCommon Macintosh problems InstalledInstalling a memory Dimm Installing accessoriesPrecautions when installing accessories Disconnect the power cordSetting the memory in the PostScript printer properties Installing a wireless network interface card Removing a DimmSelecting the authentication type Configuring the wireless network parametersConfiguring basic network settings Setting Encryption Using the hard diskInstalling the hard disk Restoring default values for wireless networkingPrinting with the optional hard disk Setting the hard disk in the printer propertiesSetting the time and date Storing a jobControlling the active job queue Printing a stored jobDeleting a stored job To delete a file from the queueTo promote a file from the queue Printing using the form filesTo print a file immediately Printer specifications SpecificationsSpecifications and Description Index System requirements Linux 3.3 Macintosh 3.3 Windows Software section Contents Using Windows Postscript Driver Using Your Printer with a Macintosh Installing Software for Local Printing Installing Printer SoftwareTypical Installation Custom Installation Select Typical installation for a local printer. Click NextSelect Custom installation. Click Next Select the components to be installed and click NextInstalling Software for Network Printing Custom Installation Select Custom installation. Click Next Reinstalling Printer Software Select the components you want to reinstall and click Next Removing Printer SoftwarePrinting a Document Select your printer driver from the Name drop-down listLayout Tab Printer SettingsPaper Orientation Source Paper TabScaling Printing Toner Save Mode Image ModeResolution Graphics TabOn the Job Setting Job SettingExtras Tab About Tab Using a Favorite SettingUsing Help Printer TabAdvanced Printing Printing Multiple Pages on One Sheet of Paper N-Up PrintingPrinting Posters Printing BookletsFitting Your Document to a Selected Paper Size Printing on Both Sides of PaperPrinting a Reduced or Enlarged Document NoneCreating a Watermark Using WatermarksUsing an Existing Watermark Editing a WatermarkUsing a Page Overlay Using OverlaysWhat is an Overlay? Creating a New Page OverlayUsing Windows PostScript Driver AdvancedOverview Direct Print Utility Using the shortcut iconUsing the right-click menu PrintingCheck the Share this printer box Setting Up a Host ComputerSetting Up a Client Computer Select Local Port and click New PortUnderstanding Smart Panel Troubleshooting GuidePrinter Setting Toner LevelUsing Printer Settings Utility Opening the Troubleshooting GuideChanging the Smart Panel Program Settings Using Onscreen Help FileInstalling the Unified Linux Driver Installing the Unified Linux DriverGetting Started Uninstalling the Unified Linux Driver Click UninstallOpening the Unified Driver Configurator Using the Unified Driver ConfiguratorPrinters Configuration Double-clickUnified Driver Configurator on the desktopPorts Configuration Configuring Printer PropertiesClasses Tab Printing Files Printing from ApplicationsFile menu Uninstalling the Printer driver Installing Software for MacintoshInstall the Printer driver Click ContinueFor a USB-connected Setting Up the PrinterFor a Network-connected Macintosh Mac OS 8.6 ~Layout Setting Changing Printer SettingsPrinting a Document Printing Multiple Pages on One Sheet of Paper Printer Features SettingResolutionQuality Reverse DuplexDuplex Printing Index Image mode 15 resolution Macintosh GGGGGGGGGGGGGRev
Top Page Image Contents