Cary Audio Design Cinema 11 Connecting a Multi Channel Power Amplifier, Second Zone Zone

Page 23

INSTALLATION

When using a TOSLINK optical input or output jack, always use a high-quality optical fiber cable.

IMPORTANT: We strongly recommend that before you connect any loudspeakers to your amplifiers, you complete all needed connections and set up procedures to your Cinema 11 as outlined below. This will reduce the chance that a wrong connection or other error will produce a high volume audio output that might damage your speakers or other components.

Given the wide variety of components that can be connected to your Cinema 11, there are numerous ways in which your system can be assembled. To help you with this task, use the chart at the end of this manual to record the components connected to your unit, as well as which type of input (analog, coaxial, Toslink, etc) is used. Keep this chart for future reference.

There are many possible ways to connect a particular device. Use the diagrams on the following pages as a guideline. The information in this section contains some of the more common situations you might encounter in your system.

Always consult the owner's manuals that come with the components you are connecting to the Cinema 11 for more information on the source component's connections.

CONNECTING A MULTI CHANNEL POWER AMPLIFIER

Before attempting to plug any jacks into any power amplifier, verify that the power amplifier is turned off and or disconnected from the AC mains. Failure to do so can potentially result in severe damage to your amplifier or loudspeakers.

Use the audio jacks labeled OUTPUT from the Cinema 11 to an external power amplifier such as the Cary Audio Cinema 7B Power Amplifier. The Cinema 11 can output up to 7.1 channels of sound depending on source components and source material.

The output jacks supplied by the Cinema 11 are: Left Front, Center, Right Front, Left Surround, Right Surround, Left Surround Back, Right Surround Back, and Subwoofer. Be sure to verify that the correct outputs are connected to the appropriate input jacks (Left Front to Left Front, Right Surround Back to Right Surround Back, etc.)

When a powered subwoofer is used, connect the Subwoofer output jack to the Line Input jack on your subwoofer and follow any specific connection and or configuration, instructions supplied with the subwoofer. If your subwoofer is a passive speaker, connect the subwoofer output jack on the Cinema 11 to the input of the amplifier used to power the subwoofer, and then connect the subwoofer speaker itself to the subwoofers’ power amplifier.

SECOND ZONE (ZONE 2)

Use the L and R channel ZONE 2 AUDIO OUTPUT audio jacks to connect the Cinema 11 to the audio inputs of an external amplifier or other audio component in a second zone. The signal present will reflect the input selection of the Cinema 11. This may be adjusted using the Zone Menu or the ZONE button on the remote control. It may be seen using the VFD MENU.

22

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Cinema Table of Contents Important Safety Instructions Important Safety Instructions FCC Information for User Congratulations on becoming a Cinema 11 owner WelcomeThank YOU Cinema 11 offers Product FeaturesFormat Descriptions Unpacking and InstallationWelcome About Dolby Pro Logic Analog Audio Section SpecificationsAudio Inputs / Audio Outputs Main Path Digital AudioFM Tuner Zone 2 PathsControl AM TunerTrigger Outputs Power RequirementsFront Panel Controls and DisplaysMaster Volume Knob Analog Audio 7.1 Input Rear PanelRS-232 Port Auto Setup MIC-INRemote Control Controls and Displays Zone 2 Power OFF Press this button to turn the Cinema 11 OFF Zone 2 Remote ControlGetting Started InstallationLocation Second Zone Zone Connecting a Multi Channel Power AmplifierPower Connection Power Control ConnectionsSpeaker Check Auto Sound SetupSet Distance CENSBR SBLSet Crossover Points Set Speaker PhaseSet Room EQ Auto Sound Setup Setup Menu Speaker Manual Sound SetupSpeaker SET Distance Setting the Speaker Distance DelaysSET Distance Speaker SET Balance SET BalanceSpeaker SET Crossover Points To Set Channel Levels Using The Test Tone FunctionSetting the Speaker Crossover Points SET Crossover PointsSET Acoustic Calibration Room EQ Setting the Acoustic Calibration Room EQ manuallyManual Sound Setup Input Setup MenuBetter sounds using SET Speaker Phase Setting the speaker phase manuallyInput Back Setup Menu123456789 =?@ABCDEFGHIJKLMNOPQRSTUVWXYZ To set Analog in Level SET Analog in Level SettingsSET Analog in Config Radio To set Analog in ConfigRadio Setup Menu Listening to the Radio Connection Chart To set Zone 2 input To set Zone 2 volumeZone Trigger To set PasswordAV Sync Delay OtherTo set IR Controls BrightEdit Custom Name To set Auto Input Seek To set Late Mode for Dolby DigitalTo set Restore Default To set TriggersNON-WARRANTY Repairs Service and CareCare and Cleaning Factory ServiceWarranty Disclaimer United States Limited WarrantyCary Audio Design

Cinema 11 specifications

Cary Audio Design has long been recognized for its commitment to high-fidelity audio equipment, and the Cinema 11 is a prime example of their engineering excellence. This preamplifier/processor combines both advanced technology and exceptional craftsmanship to create an immersive home theater experience.

One of the standout features of the Cary Audio Cinema 11 is its multi-channel processing capabilities. It supports up to 11 channels of amplification, making it a perfect fit for those looking to create a 9.1.2 or even a 7.1.4 Dolby Atmos setup. This flexibility allows users to tailor their home theater experience to their personal preferences or room dynamics.

The Cinema 11 employs Cary’s proprietary circuitry, which is designed to minimize distortion and enhance overall sound quality. This focus on audio fidelity ensures that users experience the full range of dynamic soundtracks and subtle nuances in their favorite movies and music. The processor is equipped with high-quality Digital-to-Analog Converters (DACs) that facilitate precise audio playback, contributing to a remarkable clarity that audiophiles will appreciate.

Connectivity is another area where the Cinema 11 excels. It features a comprehensive array of inputs and outputs, including HDMI, optical, and coaxial connections, along with support for the latest HDCP standards and various audio formats. This versatility allows it to seamlessly integrate with other components in a home theater system, making setup a breeze.

Moreover, the Cinema 11 incorporates advanced room correction technology, which optimizes audio playback based on the unique characteristics of the listening environment. This feature is crucial for achieving balanced sound in rooms that may pose acoustic challenges.

Cary Audio has also placed an emphasis on user experience with the Cinema 11. The unit includes an intuitive user interface and a fully customizable remote control, allowing users to easily navigate settings and features. The elegant design is aesthetically pleasing, fitting comfortably with any home décor.

In summary, the Cary Audio Design Cinema 11 stands out for its robust features, cutting-edge technology, and superior sound quality. With its emphasis on multi-channel support, advanced circuitry, extensive connectivity options, and user-friendly interface, the Cinema 11 is an ideal choice for home theater enthusiasts seeking a premium audio experience.
Top Page Image Contents