Samsung 800TFT manual Troubleshooting problems, Adjusting Your FPD

Page 18
Troubleshooting

Adjusting Your FPD

Troubleshooting

Before calling for service, check the information in this section to see if you can remedy any problems yourself

Table 3. Troubleshooting problems

Symptom

Corrective Actions

 

 

No Picture

Check to see that both the FPD and the

 

computer are plugged in and turned on.

 

 

“No Connection

Check the signal cable connection between

Check Signal Cable” appears

the computer and the FPD

 

Use the flat panel display self test described

 

on page 7.

 

 

“Video mode not supported”

Check the maximum resolution and the

 

frequency on the video port of your

 

computer.

 

Compare these values with the data in the

 

preset timing modes, page 20.

 

 

Picture is scrambled

Check the signal cable connection between

 

the computer and FPD.

 

Perform Auto Adjustment (see page 6).

 

 

Picture is not clear

Adjust Fine and Coarse adjustments as

 

needed (see page 12).

 

 

Picture is fuzzy

Perform FPD reset.

 

Eliminate accessories (i.e., video extension

 

cables).

 

 

Picture bounces or has wavy

Check the signal cable connection between

oscillations

the computer and FPD

 

 

Picture appears to be ghosting

Check the signal cable connection between

 

the computer and FPD.

 

 

The image is too light or too dark

Adjust the Brightness and Contrast settings.

 

 

Color is not uniform

Adjust the color settings using the OSM

 

COLOR menu.

 

 

The colors are distorted with dark

Adjust the color settings using the OSM

or shadowed areas

COLOR menu.

 

 

16

Image 18
Contents SyncMaster 800TFT TFT-LCD MonitorOwner’s Instructions Unpacking your Monitor DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISK OF ELECTRIC SHOCK DO NOT OPENContents Portu- Italiano Español Deutsch Français EnglishPut your FPD in a location with low humidity and a minimum of dust Figure 1. Front panel Your Flat Panel MonitorItaliano Portuguese Deutsch Español Français English 4 OSM adjustment controls and direct-access controlsconnector Figure 2. Back panel connectors13W3 signal cable connector Power adapter cable holder slotTurn off your system and unplug its power cord InstallationFigure 3. Connecting your monitor to a PC cord for your locale to the AC inlet on the power adapterGetting Help Auto AdjustmentMaintenance of Your Flat Panel Display Plug and PlayTurn on the monitor Self-Test Feature Check STFCTurn off both your computer and the monitor Figure 4. FPD self-test screenfeature control. See the section on Direct-Access Buttons Adjusting Your FPDPower button and indicator screenAuto Adjustment Direct-Access FeaturesAuto Adjustment Español Français EnglishContrast OSM Lock/UnlockContrast or “+”Portuguese Deutsch Español Français English Coarse 1688 Auto AdjustmentAccessing the Menu System ItalianoFine and Coarse adjustments Table 1. Menu Adjustmentsclosely adjust your FPD to your preference the interference. If satisfactory results are notto their original factory settings Adjusting Your FPDTable 1. Menu Adjustments Continued button. The default time is 10 secondssee more detail new settingsoftware you are using nizePowerSaver Table 2. Power-saving modesTroubleshooting Table 3. Troubleshooting problemsTable 3. Troubleshooting problems Continued The power indicator blinks amberSpecifications Referring to Standard signal modes, pageAppendix Table 4. SpecificationsTable 6. 13W3 Connector Pin AssignmentsTable 7. Preset timing modes Display ModesPortuguese Deutsch Español Turn off your monitor and unplug its power cordFrançais English Changing the StandIndex FCC Information Regulatory InformationPortuguese Italiano Español Deutsch Français English IC Compliance NoticeU.S.A
Related manuals
Manual 26 pages 44.16 Kb Manual 24 pages 15.22 Kb