Samsung 800TFT manual Installation, Français, Italiano Portuguese Deutsch Español, simultaneously

Page 7
Installation

Installation

English

1

English3

4

2

5

To workstation

video port

6

Français

Figure 3. Connecting your monitor to a PC

1

Turn off your system and unplug its power cord.

2

Place the FPD facedown on a cushion (being careful not to harm the screen) so that

you can access the cable connectors along the bottom of the rear recess.

3

When connecting your FPD to a computer: Connect the supplied signal cable to the

15-pin mini D-sub connector on the back of your FPD. Connect the other end of the

 

cable to the video port on the back of your computer.

 

When connecting your FPD to a workstation: Connect an optional signal cable to the

 

13W3 connector on the back of your FPD. Connect the other end of the cable to the

 

video port on the back of your workstation. An adapter may be required.

 

NOTE: One or both types of signal cables can be connected to the FPD,

 

simultaneously.

4

Connect the power adapter jack to the power port on the back of the FPD. To

prevent dislodging the jack, slide the power adapter cable into the cable holder. Insert

 

the cable holder into the holder slot and turn it 1/4 turn. Connect the proper power

 

cord for your locale to the AC inlet on the power adapter.

5

Place your FPD upright on your desk and plug the power cords from your system and

your FPD into a nearby outlet.

6

Turn on your system and FPD. If your FPD displays an image, installation is complete.

7

Perform the auto adjustment procedure as described in “Auto Adjustment” on page 6

 

5

Italiano Portuguese Deutsch Español

Image 7
Contents TFT-LCD Monitor SyncMaster 800TFTOwner’s Instructions RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL Unpacking your MonitorPortu- Italiano Español Deutsch Français English ContentsPut your FPD in a location with low humidity and a minimum of dust 4 OSM adjustment controls and direct-access controls Your Flat Panel MonitorItaliano Portuguese Deutsch Español Français English Figure 1. Front panelPower adapter cable holder slot Figure 2. Back panel connectors13W3 signal cable connector connectorcord for your locale to the AC inlet on the power adapter InstallationFigure 3. Connecting your monitor to a PC Turn off your system and unplug its power cordPlug and Play Auto AdjustmentMaintenance of Your Flat Panel Display Getting HelpFigure 4. FPD self-test screen Self-Test Feature Check STFCTurn off both your computer and the monitor Turn on the monitorscreen Adjusting Your FPDPower button and indicator feature control. See the section on Direct-Access ButtonsEspañol Français English Direct-Access FeaturesAuto Adjustment Auto Adjustmentor “+” OSM Lock/UnlockContrast ContrastItaliano Coarse 1688 Auto AdjustmentAccessing the Menu System Portuguese Deutsch Español Français Englishthe interference. If satisfactory results are not Table 1. Menu Adjustmentsclosely adjust your FPD to your preference Fine and Coarse adjustmentsbutton. The default time is 10 seconds Adjusting Your FPDTable 1. Menu Adjustments Continued to their original factory settingsnize new settingsoftware you are using see more detailTable 2. Power-saving modes PowerSaverTable 3. Troubleshooting problems TroubleshootingThe power indicator blinks amber Table 3. Troubleshooting problems ContinuedTable 4. Specifications Referring to Standard signal modes, pageAppendix SpecificationsPin Assignments Table 6. 13W3 ConnectorDisplay Modes Table 7. Preset timing modesChanging the Stand Turn off your monitor and unplug its power cordFrançais English Portuguese Deutsch EspañolIndex IC Compliance Notice Regulatory InformationPortuguese Italiano Español Deutsch Français English FCC InformationU.S.A
Related manuals
Manual 26 pages 44.16 Kb Manual 24 pages 15.22 Kb