Samsung 800TFT manual Display Modes, Preset timing modes, Appendix

Page 22

Appendix

Display Modes

If the signal from the system equals to the standard signal mode, the screen is adjusted automatically. If the signal from the system doesn't equal to the standard signal mode, adjust the mode with referring to the Videocard user guide because the screen might not display or only the power LED might be on. For the display modes listed below, the screen image has been optimized during manufacture.

Table 7. Preset timing modes

	Horizontal	Vertical	Pixel Clock	Sync Polarity
	Frequency	Frequency	Pixel Clock	Sync Polarity
Display Mode	Frequency	Frequency	(MHz)	(H/V)
Display Mode	(kHz)	(Hz)	(MHz)	(H/V)
	(kHz)	(Hz)

720 x 400	31.469	70.087	28.322	–/+

640 x 480	31.469	59.940	25.175	–/–

640 x 480	37.500	75.000	31.500	–/–

640 x 480	43.269	85.008	36.000	–/–

800 x 600	46.875	75.000	49.500	+/+

800 x 600	53.674	85.061	56.250	+/+

1024 x 768	48.363	60.004	65.000	–/–

1024 x 768	60.023	75.029	78.750	+/+

1024 x 768	68.677	84.997	94.500	+/+

1280 x 1024	79.976	75.025	135.000	+/+

Image 22

Contents TFT-LCD Monitor SyncMaster 800TFTOwner’s Instructions Unpacking your Monitor DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISK OF ELECTRIC SHOCK DO NOT OPENContents Portu- Italiano Español Deutsch Français EnglishPut your FPD in a location with low humidity and a minimum of dust Figure 1. Front panel Your Flat Panel MonitorItaliano Portuguese Deutsch Español Français English 4 OSM adjustment controls and direct-access controlsconnector Figure 2. Back panel connectors13W3 signal cable connector Power adapter cable holder slotTurn off your system and unplug its power cord InstallationFigure 3. Connecting your monitor to a PC cord for your locale to the AC inlet on the power adapterGetting Help Auto AdjustmentMaintenance of Your Flat Panel Display Plug and PlayTurn on the monitor Self-Test Feature Check STFCTurn off both your computer and the monitor Figure 4. FPD self-test screenfeature control. See the section on Direct-Access Buttons Adjusting Your FPDPower button and indicator screenAuto Adjustment Direct-Access FeaturesAuto Adjustment Español Français EnglishContrast OSM Lock/UnlockContrast or “+”Portuguese Deutsch Español Français English Coarse 1688 Auto AdjustmentAccessing the Menu System ItalianoFine and Coarse adjustments Table 1. Menu Adjustmentsclosely adjust your FPD to your preference the interference. If satisfactory results are notto their original factory settings Adjusting Your FPDTable 1. Menu Adjustments Continued button. The default time is 10 secondssee more detail new settingsoftware you are using nizePowerSaver Table 2. Power-saving modesTroubleshooting Table 3. Troubleshooting problemsTable 3. Troubleshooting problems Continued The power indicator blinks amberSpeciﬁcations Referring to Standard signal modes, pageAppendix Table 4. SpeciﬁcationsTable 6. 13W3 Connector Pin AssignmentsTable 7. Preset timing modes Display ModesPortuguese Deutsch Español Turn off your monitor and unplug its power cordFrançais English Changing the StandIndex FCC Information Regulatory InformationPortuguese Italiano Español Deutsch Français English IC Compliance NoticeU.S.A

Related manuals

Manual 26 pages 44.16 Kb

Manual 24 pages 15.22 Kb