Technicolor - Thomson ITC250S manual Chapter General operation

Page 10

 

 

Chapter 3

 

General operation

 

 

 

 

 

 

 

Switching the TV set on and off

 

 

 

To switch the TV set on, press the A button located under the front panel of the set.

 

 

 

The TV set takes up to 40 seconds to come on.

 

 

 

 

If the indicator on the front is red, the set is in standby mode.You can then:

 

 

 

- press the

or any numeric button on the remote control,

 

 

 

- press the TV, OK or PR+/PR- buttons to switch the television on at the last channel

 

 

 

or AV programme you were watching,

 

 

 

 

- press the AV button to switch the television on at the last AV programme you were

 

 

 

watching.

 

 

EN

 

 

 

 

 

 

When the set is on, the indicator on the front is blue.

 

 

 

To put the TV set in standby mode, press the

button on the remote control.When

 

 

 

 

 

 

the set is in standby mode,the indicator on the front is red.The TV set remains

 

 

 

powered up, but with low energy consumption.

 

To switch off the TV set, press the on/off button under the front panel of the set.

Note:The fan continues to run for about another two minutes after the TV set has been switched off.

Volume

Volume control: use the +/- buttons on the front of the TV set or press the relevant buttons on the remote control to increase or decrease the volume.

Sound mute: press the button to temporarily mute the sound. Press this button again or the + button to restore it.

Headphone volume control: press the +/- button on the remote control to

display the volume control bar.Then use the buttons to switch to the

headphone volume control bar. Use the buttons to adjust the volume.

Displaying status information

In TV mode, press the yellow button (INFO) on the remote control to display the number and name of the channel you are watching, the time, the type of sound, the zoom or format, and the status of the Parental control function.

If the programme guide is available for this channel, the name of the programme currently showing is displayed, along with its start time and duration and the name and start time of the following programme are also displayed.

When you switch on the television or change channels, the number and name of the channel are displayed.

Note: If you activate the Permanent pr. number function in the Preferences menu, the channel number will be displayed permanently (see page 18).

Accessing channels

Using the numeric buttons:

-for channels 1 to 9, press the corresponding button;

-for channels 10 to 99,

-press the tens digit for a few seconds to display it on the screen, then press the units digit. For instance, for programme 24, press and hold 2 to display 2-, then press 4; or

-press the 0 button to display “--”, then enter the two digits.

Using the PR+/PR- buttons: scroll through the channels. AV programmes are not included in the cycle unless you use the buttons on the front of the TV set.

Using the list of programmes: refer to page 11.

To access the channel or AV programme previously being watched, press the RETURN button

Accessing AV programmes

Press the AV button to display the last selected audio-visual programme and scan through the other audio-visual programmes.

10

Image 10
Contents Contents Important information SafetyChapter Getting started CareSpecific precautions for DLP TV sets Getting startedUsing the remote control for other equipment Remote controlProgramming the remote control Manual programming Programming the volume control functionVideo recorder DVD player Satellite receiver Hi-fi system Clearing a Learned Function Learning featureAdding a Learned Function Deleting ALL Learned FunctionsSwitching on Chapter Install Manual installation option and press OKRepeat this procedure to find other channels Channel set-upChapter General operation General operation Headphone settings Adjusting the soundConfiguring the sound settings Advanced functionsAdvanced functions Adjusting the pictureGraphic equaliser Use Lamp & PositionPosition Programming the sleep timer Setting the timeSetting the time Programming the wake-up timerParental control Accessing the Parental control menuOperation TV mode Locking the buttons on the front of the TV setPicture in picture PIP Split screen modeOverview menu Preferences Customising your televisionPreferences Install menu Configuring AV socketsSettings Teletext Accessing TeletextNavigator Other Teletext functions Recording a programme Program Info programme guideDefining search criteria, such as day and period time slot Storing a programmeChecking your selections in the Review screen Removing the front panel piece Accessing the socket panelChapter Other information SocketsConnecting an amplifier Connecting headphonesConnecting active speakers Connecting a video recorderAbout NexTView Link Setting up channelsSetting a programme to record Copying cassettes