Getting started
Manual programming
This method involves carrying out a manual search for the codes to be used for controlling your other appliances.
1.Switch on the appliance you wish to use the remote control with.
2.Press the relevant button for this appliance on the remote control, and while holding this button down, enter one of the codes relevant to your make of appliance (there is a list of codes at the end of this manual). If the light or the appliance buttons of the remote control flash you have entered the wrong code or it is not possible to program the remote control.
3.Point the remote control at the appliance and press the relevant button (VCR, DVD, etc). Press the 
standby button. If the appliance does not go into standby mode, try another code.
Depending on the year of manufacture and the type of appliance, some functions may not | VCR |
|
|
|
| AUX |
|
|
|
| |||
be available. Certain codes may cover more functions than others.Test the functions you | DVD |
|
|
|
| AMP |
|
|
|
| |||
can control and, if appropriate, try other codes. |
| SAT |
|
|
|
|
|
|
|
|
| ||
Note here the code(s) which work best. |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
When you change the remote control’s batteries, remember to reprogram it. |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Video recorder | DVD player | Satellite receiver |
|
| ||||||||
| Press the VCR button | Press the DVD button | Press the SAT button |
| Press the AMP button | ||||||||
| On/Standby | On/Standby | On/Standby |
|
|
| On/Standby | ||||||
MENU | To display the main menu | To display the main menu | To display the main menu |
|
|
|
|
|
|
|
| ||
| Vertical scrolling in menus | Vertical scrolling in menus | Vertical scrolling in menus |
|
|
|
|
|
|
|
| ||
| Horizontal scrolling | Horizontal scrolling | Horizontal scrolling |
|
|
|
|
|
|
|
| ||
| in menus | in menus | in menus |
|
|
|
|
|
|
|
|
|
|
OK | To confirm an action | To confirm an action | To confirm an action |
|
|
|
|
|
|
|
| ||
EXIT | To close a menu | To close a menu | To close a menu |
|
|
|
|
|
|
|
|
|
|
To directly access channels | To enter numeric values | To directly access channels |
| To select a station using | |||||||||
| or enter numeric values | or select options in menus | or enter numeric values |
| its number | ||||||||
PR+/PR- | To change channels | To change chapters | To change channels |
| To change stations | ||||||||
AV | To select av input | To select av input |
|
|
|
|
|
|
|
|
|
|
|
REV | Rewind | Rewind |
|
|
|
|
|
|
|
|
|
|
|
PLAY | Play | Play |
|
|
|
|
|
|
|
|
|
|
|
FWD | Fast forward | Fast forward |
|
|
|
|
|
|
|
|
|
|
|
STOP | Stop | Stop |
|
|
|
|
|
|
|
|
|
|
|
PAUSE | Pause picture | Pause picture |
|
|
|
|
|
|
|
|
|
|
|
REC | Record |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| To switch the sound off and | ||||||
|
|
|
|
|
|
| back on again | ||||||
+/- |
|
|
|
|
|
| To set the volume level | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Programming the volume control function
If you have programmed the TV remote control to use with other appliances and these are connected to an amplifier you can also programme the remote control to adjust the volume when you are using one of these appliances.The example below describes the procedure for programming a DVD player.
1.Programme the AMP button on the remote control to use with the amplifier (refer to page 4).
2.Move the remote control away from the appliances. Press the 
- button and while holding it down, press the relevant mode button (DVD, in this example), then the AMP button. Release the 
- button.
3.Switch on the amplifier, then the DVD player.
4.Set the remote control to DVD, play a disc and adjust the volume using the 
+/- buttons.
Repeat this operation for the other appliances.
To cancel the programmed function for any of the appliances, press the 
- button, while holding it down and enter the code 000 using the numeric buttons.
EN
5