Mitsubishi Electronics MDT521S user manual CAT5 Tx BOX, Operating Range for the Remote Control

Page 10

<Operating Range for the Remote Control >

Point the top of the remote control toward the LCD monitor's remote sensor during button operation.

Use the remote control within a distance of about 7 m/23 ft. from the front of the LCD monitor's remote control sensor and at a horizontal and vertical angle of within 30° within a distance of about 3 m/10 ft.

30° 30°

CAUTION:

Important, the remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor, or when there is an object in the path.

< Handling the remote control >

*Do not subject to strong shock.

*Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immedi- ately.

*Avoid exposure to heat and steam.

*Other than to install the batteries, do not open the remote.

CAT5 Tx BOX

USB (B type)

Connected to the USB connector (A type) of the computer.

CAUTION:

We have checked the operation of the USB connector by connecting it with our computers according to the USB stan- dards.

When the CAT TX5 BOX is combined with your computer system or USB hub system, check in advance that it operates properly.

EXTERNAL CONTROL IN (mini D-Sub 9 pin)

Connected to the RS-232C OUT connector of the computer.

Note:

RS-232C connection isn’t necessary when the COM port number set by the USB driver is used. Make selection using the input select switch (USB/RS-232C), as necessary.

RGB IN (mini D-Sub 15 pin)

To input the analog RGB signals from other monitor.

RGB OUT (mini D-Sub 15 pin)

To output the analog RGB signals from a computer.

Input select switch (USB/RS-232C)

Switches the control input between the USB connector and the RS-232C connector.

CAT5 OUT (modular connector 8 pin)

Connected to the CAT5 (RGB5) IN connector of MDT521S.

Composite sync signal level switch

Switches the composite sync signal level.

The TTL level and the 0.3V level are switched.

Auxiliary power supply input connector (DC IN 5 V)

Though the power is supplied from the above-mentioned USB connector, an auxiliary DC power adopter (commercially available) is also available. Power can be drawn from the USB connector and the auxiliary power supply at the same time.

CAUTION:

The auxiliary power supply input connector isn’t intended for general use. Commercial DC power connectors are available in different shapes. When you want to use this connector, consult a qualified electrician in advance.

English

English-9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents LCD Display Monitor HOW to Setup Schedule IndexImportant Information Declaration of ConformityDeclaration Declaration of the ManufacturerRecommended Use ErgonomicsContents Buttons, Switch, and Indicator Parts Name and FunctionsConnectors and Terminals CAT5 input/output connectors modular con- nector 8 pinWireless Remote Control Picture Mode buttonHandling the remote control Operating Range for the Remote ControlCAT5 Tx BOX Setup Procedure Adjust the image See Adjust the soundAdjust the screen See pages Recommended AdjustmentLandscape When MDT521S is installed in portrait positionCAT5 video connection Connection of the CAT5 video connec- tion functionAllowable cable length Various settings involved in the CAT5 video connectionConnection to multiple monitors CAT5 EQVentilation Requirements for enclosure mounting Upright position Lay the screen face downTo avoid monitor from falling Before making connections Wiring DiagramConnections HdmiConnecting a Personal Computer Connect the LCD Monitor to a Personal ComputerConnect the LCD Monitor to a Computer with a Digital Output Connecting with Digital Interface EquipmentDVI-D BNC-RCA Connect the LCD Monitor to a DVD PlayerRCA DVI-D Hdmi BNC RCA Connecting to a VCR / Stereo AmplifierConnect the LCD Monitor to a VCR / Stereo Amplifier BNCPressing the power button Power on and OFF ModesPressing the Main Power Switch Using the remote controlPicture Mode Power IndicatorUsing Power Management Audio Source SwitchingDVD/HD Information OSDRGB1, 2, 3, 4 VIDEOS, VideoOSD On-Screen-Display Controls Picture Auto Brightness Picture ResetFront Sensor Select on for normal use Screen Audio PIP Picture in PictureConfiguration Serial Control OFF TimerCAT5 Cable Length RS485 TerminationIR Control Film ModeAdvanced Option TilingDVI Input Mode Power on DelayHdmi Input Mode Advanced Option ResetImage Persistence HOW to Setup ScheduleRecommendations Supplemental information of the auto brightness function PIP, POP and Side by SideTo control multiple monitors collectively Remote control numbering function To use a computer to control the monitorsControl command diagram InterfaceRead command Operation commandsControl sequence Features Troubleshooting No Signal is displayed on the screen Remote Control is not availableSCHEDULE/OFF Timer function is not working properly No SoundSpecifications Specifications MDT521SPin Assignment GND Mini DIN 4PRXD TXD GND RTS CTS North America Mitsubishi Contact InformationEurope
Top Page Image Contents