Mitsubishi Electronics MDT521S user manual Setup Procedure

Page 11

Setup Procedure

1. Determine the installation location

CAUTION:

DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF.

Installing your LCD display must be done by a qualified tech- nician. Contact your dealer for more information.

CAUTION:

MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE.

Failure to follow this caution may result in injury if the LCD monitor falls.

CAUTION:

Do not mount or operate the display upside down, face up, or face down.

CAUTION:

Do not install the LCD monitor where it will be exposed to direct sunlight, as this will result in display defects.

CAUTION:

This LCD has a temperature sensor and cooling fan. If the LCD becomes too hot, the cooling fan will turn on automati- cally. If the LCD becomes overheated and the cooling fan is running, the “Caution” menu will appear. If the “Caution” menu appears, discontinue use and allow the unit to cool. When the LCD monitor is used in an enclosure or with protec- tion on LCD surface, please check the inside temperature of monitor by “HEAT STATUS” (See page 31). The temperature is too hot than normal condition, please set “cooling fan” to ON on SCREEN SAVER function (See page 28).

IMPORTANT:

Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel.

2. Installing and removing the remote control batteries

The remote control is powered by 1.5V AAA batteries. To install or replace batteries:

How to install the batteries

1.Unlock and pull up the cover in the arrow’s direction.

2.Align the batteries according to the (+) and (–) indications inside the case.

3.Replace the cover.

How to remove the batteries

1.Unlock and pull up the cover in the arrow’s direction.

2.Remove the batteries.

CAUTION:

Incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points.

•Place “AAA” batteries matching the + and - signs on each battery to the + and - signs of the battery compartment.

•Do not mix battery types.

•Do not combine new batteries with used ones. It causes shorter battery life or leakage of batteries.

•Remove dead batteries immediately to prevent battery liquid from leaking into the battery compartment. Don't touch exposed battery acid, it cause damage to your skin.

NOTE:

If you do not intend to use the Remote Control for a long period, remove the batteries.

3. Connect external equipment (See page 15-18)

•To protect the connected equipment, turn off the main power before making connections.

•Refer to your equipment user manual.

4. Connect the supplied power cord

•The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

•Fully insert the prongs into the power outlet socket. Loose connection may cause noise.

NOTE:

Please refer to “Safety Precautions, Maintenance & Recommended Use” section of this manual for proper selection of AC power cord.

Clamper

Use the clamper

to secure the

cable firmly.

5. Switch on the power of all the attached external equipment

When connected with a computer, switch on the power of the computer first.

English-10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents LCD Display Monitor Index HOW to Setup ScheduleDeclaration of Conformity Important InformationDeclaration of the Manufacturer DeclarationErgonomics Recommended UseContents Parts Name and Functions Buttons, Switch, and IndicatorCAT5 input/output connectors modular con- nector 8 pin Connectors and TerminalsPicture Mode button Wireless Remote ControlCAT5 Tx BOX Operating Range for the Remote ControlHandling the remote control Setup Procedure Recommended Adjustment Adjust the soundAdjust the screen See pages Adjust the image SeeConnection of the CAT5 video connec- tion function When MDT521S is installed in portrait positionCAT5 video connection LandscapeCAT5 EQ Various settings involved in the CAT5 video connectionConnection to multiple monitors Allowable cable lengthTo avoid monitor from falling Upright position Lay the screen face downVentilation Requirements for enclosure mounting Hdmi Wiring DiagramConnections Before making connectionsConnect the LCD Monitor to a Personal Computer Connecting a Personal ComputerDVI-D Connecting with Digital Interface EquipmentConnect the LCD Monitor to a Computer with a Digital Output RCA DVI-D Hdmi Connect the LCD Monitor to a DVD PlayerBNC-RCA BNC Connecting to a VCR / Stereo AmplifierConnect the LCD Monitor to a VCR / Stereo Amplifier BNC RCAUsing the remote control Power on and OFF ModesPressing the Main Power Switch Pressing the power buttonAudio Source Switching Power IndicatorUsing Power Management Picture ModeVIDEOS, Video Information OSDRGB1, 2, 3, 4 DVD/HDOSD On-Screen-Display Controls Picture Front Sensor Select on for normal use Picture ResetAuto Brightness Screen PIP Picture in Picture AudioConfiguration RS485 Termination OFF TimerCAT5 Cable Length Serial ControlTiling Film ModeAdvanced Option IR ControlAdvanced Option Reset Power on DelayHdmi Input Mode DVI Input ModeRecommendations HOW to Setup ScheduleImage Persistence To control multiple monitors collectively PIP, POP and Side by SideSupplemental information of the auto brightness function To use a computer to control the monitors Remote control numbering functionInterface Control command diagramControl sequence Operation commandsRead command Features Troubleshooting No Sound Remote Control is not availableSCHEDULE/OFF Timer function is not working properly No Signal is displayed on the screenSpecifications MDT521S SpecificationsPin Assignment RXD TXD GND RTS CTS Mini DIN 4PGND Europe Mitsubishi Contact InformationNorth America
Top Page Image Contents