Mitsubishi Electronics MDT521S Various settings involved in the CAT5 video connection, CAT5 EQ

Page 14

2.Connect the D-SUB input connector of the CAT5 Tx BOX and the VGA (D-SUB) output connector of the computer using the signal cable (mini D-SUB 15-pin cable) supplied with the monitor.

3.Connect the modular connector of the CAT5 Tx BOX and the CAT5 (RGB5) IN connector of the monitor using a commercially available CAT5 cable.

2) Connection to multiple monitors

USB cable

Computer

CAT5 cable

CAT5 Tx BOX (supplied)

Monitor

VGA (mini D-SUB 15-pin) cable (supplied)

Monitor

CAT5 cable

…

1.In addition to the connection made step 1) above, con- nect the CAT5 OUT connector of the first monitor and the CAT5 (RGB5) IN connector of the second monitor using a commercially available CAT5 cable.

2.Connect the third and later monitors in the same way. You can connect up to 5 monitors.

Allowable cable length

Connection

Max. cable length/signal timing

 

 

One monitor

150 m / 1920 x 1080 @60 Hz

 

 

Multiple moni-

200 m / 1920 x 1080 @60 Hz

tors

(Total length of the connected cables)

 

 

The lengths given above are based on the actual measure- ments using our standard signal source and the recommend- ed cable as follows. Before installation, check the monitor operation in advance by connecting it with your computer and cables.

Recommended cable:

8-pin modular connector, straight-through, shielded, Category 5 or 5e

3. Various settings involved in the CAT5 video connection

In the case of the CAT5 video connection, configure the fol- lowing settings displayed on the OSD screen. (See page 29.)

1) CAT5 CABLE LENGTH

Select the cable length, and the defaults of all the adjustment values are automatically determined.

Select the length that is closest to the actual length of your cable.

2) CAT5 EQ

Make adjustment so that blur and smear of the displayed let- ters and graphic objects are minimized.

3) CAT5 R-GAIN/G-GAIN/B-GAIN

When the displayed image is dark, increase each value. When whites aren’t displayed as intended, adjust the R-GAIN and B-GAIN values.

4) CAT5 R-SKEW/G-SKEW/B-SKEW

Adjust each value so that the color deviation in the displayed letters and graphic objects is minimized.

English

English-13

Page 13 Page 15
Image 14
Page 13 Page 15
Contents LCD Display Monitor HOW to Setup Schedule IndexImportant Information Declaration of ConformityDeclaration Declaration of the ManufacturerRecommended Use ErgonomicsContents Buttons, Switch, and Indicator Parts Name and FunctionsConnectors and Terminals CAT5 input/output connectors modular con- nector 8 pinWireless Remote Control Picture Mode buttonCAT5 Tx BOX Operating Range for the Remote ControlHandling the remote control Setup Procedure Adjust the image See Adjust the soundAdjust the screen See pages Recommended AdjustmentLandscape When MDT521S is installed in portrait positionCAT5 video connection Connection of the CAT5 video connec- tion functionAllowable cable length Various settings involved in the CAT5 video connectionConnection to multiple monitors CAT5 EQTo avoid monitor from falling Upright position Lay the screen face downVentilation Requirements for enclosure mounting Before making connections Wiring DiagramConnections HdmiConnecting a Personal Computer Connect the LCD Monitor to a Personal ComputerDVI-D Connecting with Digital Interface EquipmentConnect the LCD Monitor to a Computer with a Digital Output RCA DVI-D Hdmi Connect the LCD Monitor to a DVD PlayerBNC-RCA BNC RCA Connecting to a VCR / Stereo AmplifierConnect the LCD Monitor to a VCR / Stereo Amplifier BNCPressing the power button Power on and OFF ModesPressing the Main Power Switch Using the remote controlPicture Mode Power IndicatorUsing Power Management Audio Source SwitchingDVD/HD Information OSDRGB1, 2, 3, 4 VIDEOS, VideoOSD On-Screen-Display Controls Picture Front Sensor Select on for normal use Picture ResetAuto Brightness Screen Audio PIP Picture in PictureConfiguration Serial Control OFF TimerCAT5 Cable Length RS485 TerminationIR Control Film ModeAdvanced Option TilingDVI Input Mode Power on DelayHdmi Input Mode Advanced Option ResetRecommendations HOW to Setup ScheduleImage Persistence To control multiple monitors collectively PIP, POP and Side by SideSupplemental information of the auto brightness function Remote control numbering function To use a computer to control the monitorsControl command diagram InterfaceControl sequence Operation commandsRead command Features Troubleshooting No Signal is displayed on the screen Remote Control is not availableSCHEDULE/OFF Timer function is not working properly No SoundSpecifications Specifications MDT521SPin Assignment RXD TXD GND RTS CTS Mini DIN 4PGND Europe Mitsubishi Contact InformationNorth America
Top Page Image Contents