Mitsubishi Electronics 164 Series manual Auto Setup, Microphone Placement, Initial Preparation

Page 40

403. TV Features

Sound Projector, continued

Auto Setup

265 Series

Auto setup uses the included calibration microphone to optimize Sound Projector performance for most room conditions.

Initial Preparation

1.

Position and connect the TV as described under

 

“Before You Begin,” page 38.

2.

Power on the TV and external subwoofer, if any.

3.

Plug the microphone cable into the TV’s INPUT 3

 

left audio jack.

Microphone Placement

Make sure there are no large obstacles between the TV and microphone.

Place the microphone

-- On a flat, level surface at least six feet away from the front of the TV.

-- On a tripod or on the backrest of your seating.

-- At the same height yours ears would be when watching TV. The height must be within 3 vertical feet of the height of the TV’s speaker array.

-- Centered in front of the TV, not off to the side.

4. Place the microphone as described in the guide-

lines on this page.

Start Auto Setup

5. Press MENU and go to Sound > AutoSP.

TV

6 ft. minimum

Microphone

Set the microphone on a level surface at ear height at least six feet from the TV. Use a seat backrest or tripod so as to pick up sound from all directions.

Maximum height above speakers

6.

Highlight START and press ENTER.

7.

Quietly exit the room right away. The calibration

 

sequence will start in a few seconds and may be

 

loud. It is important to leave the room as your pres-

 

ence will interfere with the calibration process.

8.

Wait for completion of setup before returning to the room.

9.

Play some sample audio material to check the

 

sound quality.

Note: Do not perform manual adjustments after run- ning Auto setup, as this will erase all settings defined during Auto setup.

10.Store the microphone out of direct sunlight and away from heat.

Height of TV speakers

Be sure the 3 ft. height of the

microphone is within three feet of the speaker height.

Microphone

Center the micro- phone in front of the TV.

DownloadedFor assistanceFrom TV-Manualcall.com1(800)Manuals 332-2119

Image 40
Contents Series FCC Declaration of Conformity Contents Installation and Operating Notes Important Information About Your TVReplacement Parts Outdoor Antenna GroundingStand Installation BackWall-Mounting Stand Removal Prior to Wall-MountingSpecial Features of Your TV Package Contents Installing the Remote Control BatteriesBefore You Begin First-Time Power-On Controlling Sound VolumeTV Tips Turning the TV On or OffRemote Control TV ControlsTools Key and Menu ToolsPicture Sound Picture Advanced menu, selectPower Indicator System ResetTV Control Panel Panel-Lock ReleaseSetting Up TV Inputs Using the ANT Antenna InputSetting Up Inputs with Auto Input Sensing Memorizing Channels with Channel Scan For the ANT inputWhen You First Connect a Device About Auto Input SensingAuto Input Sensing for Most Devices Tips on Auto SensingCancel Basic TV OperationSelecting an Input to Watch Watching Broadcast TVPicture Settings Basic Audio ControlsTV Care AssistanceMore TV Features FeatureFormat Key and Picture Shape Input Selection menu Inputs Name menuConnecting a Computer to the TV Hdmi ConnectionDVI Video Connection Compatible with VGA analogUsing the TV with a Personal Computer Computer Video AdjustmentsImage Resolution Computer Display FormatsBefore You Begin Auto Input SensingConnection Types Picture QualityInputs and Outputs Cable RoutingOutput CENTER-CH LANUSB Power Only ANT AntennaHdmi Inputs High-Definition Multimedia Interface Video Composite VideoAuto Input Sensing Hdmi DeviceAny Hdmi device Hdmi and Digital Surround Sound Pb Pr Component Video Device DVI Video DeviceDigital DVI Device SatelliteAntenna or Cable TV Service VCR or DVD Recorder to an Antenna or Wall Outlet CableComposite Video Device VCR or other device with composite video outputReceiver with Hdmi Output ReceiverDVD player Supplemental Audio Connections Using the TV Speakers as a Center ChannelAdding a Subwoofer Sleep Timer Setting the Sleep TimerViewing or Changing the Sleep Timer FAV Favorite ChannelsUsing ChannelView Listings Using Custom Channel BanksChannelView Channel Listings About ChannelViewStatus Display Signal DefinitionsAbout Channel Numbers Controlling A/V Receiver Sound Volume Using an External Sound SystemRedirecting Audio Output Picture Shape and Display Formats Format DefinitionsEffect of Mitsubishi Formats on Picture Types DVD Image DefinitionsUSB Source Devices Camera Images and Music FilesUSB Media Player Menu Using the Photos and Audio Menus USB Media Setup MenuKey For Photos or Audio Tracks Slideshow + Music --Slideshow only Music onlyUsing an Audio-Only Device Photos and Motion Video as Composite VideoOptional Unused 1. RCA-style plug Plug in firstWireless Audio Playback Pairing the TV with an Audio Playback DeviceResetting Bluetooth Pairing or Connection Tips for Wireless PlaybackBasic Manual Setup Sound ProjectorSound Projector Technology Before You BeginAdjusting Levels Adjusting Beam AnglesAdjusting an External Subwoofer Auto Setup Microphone PlacementStart Auto Setup Initial PreparationExternal Rear Speakers Transmitter Polk Audio F/XSpeaker unit Audio inputsStreamTV Internet Media Home Network SetupEthernet Connection Key Use for Wireless Connection@ # $ % * + = . space ? Using StreamTV Internet Media TroubleshootingUsing Vudu Apps and Vudu Movies Getting Started with Vudu MoviesSource device connected directly to the TV Introduction to Home-Theater ControlMain Menu PicturePicture Picture+ Picture Reset Using PerfectColorUsing PerfecTint Picture PerfectSound Sound AudioSound Global Sound Auto SPSound SoundPro SAPCaptions Setup Setup LanguageSetup Clock Setup TimerAdding/Deleting Channels Using the Channel Edit Menu Setup ChannelPhysical Digital Channel Number. Setup Network Setup EnergyEthernet Connection Dhcp automatic, Manual Connection Data Inputs Inputs NameInputs Inputs ControlInputs Order Inputs DemoLock Lock Parental TV-YLock Time Lock ChannelLock Panel Lock OtherAbout NetCommand IR Control Important Note on NetCommandPlacement Highlight IR-NetCommand OutputIR Emitters If You are Unable to Locate a Device’s IR SensorInitial NetCommand Setup NetCommand SetupNetCommand and Device-Specific Keys Adding or Removing Device Keys from NetCommand Control Controlling Most Device TypesSpecial Operation Description and Setup How to Use Operating NetCommand-Controlled DevicesSpecial Operation Methods Enter digits Cancel Cancel as the Cancel or Exit FunctionSeparator NetCommand Specialized Device Keys Fav FavoritesMenu InfoSwitching Audio to and from the A/V Receiver Controlling A/V Receiver PowerControlling Other A/V Receiver Functions With Any Connection TypeSetting Up A/V Receiver Control Power and VolumeSetup to Control A/V Receiver Power and Volume Before You BeginMore About Using an Hdmi Connection Automatic Audio/Video Switching Over an Hdmi ConnectionPerform NetCommand setup Before You Begin Open the Inputs Learn menu Appendices Appendix a Programming the Remote Control Functions Available for Other A/V DevicesAudio Lock Universal A/V Receiver Control Programming the Remote ControlCode Verification Video Accessories Audio AccessoriesAudio Amplifiers Satellite Receivers VCRsAppendices77 TAG Blu-ray and HD-DVDMitsubishi Home Theater TV Bypassing the Parental LockThis page intentionally left blank Appendix C Hdmi Control of CEC Devices Enabling Hdmi Control of CEC DevicesHas No Hdmi Control Option Hdmi cable cannot support CEC ActionHdmi Control of an Hdmi A/V Receiver and Connected Devices VCRUsing Hdmi Control Resolving CEC ConflictsCare of the Remote Control Cleaning RecommendationsAppendix D TV Care TV Reset Comparison Guide Appendix E TroubleshootingService and Customer Support See the Setup Channel Edit If the New DeviceNew Device Found screen Read the ON-SCREENGeneral TV Operation Symptom Remarks VuduTV Channels Symptom Remarks TV Power On/Off Symptom RemarksPicture Symptom Remarks Sound Symptom Remarks Check that Digital Audio Output and/or AVR/SURROUNDAppendices91 Trademark and License Information Mitsubishi TV Software END-USER License Agreement for Embedded SoftwareGNU General Public License Conveying Verbatim Copies Acceptance Not Required for Having Copies GNU General Public License Version 2, JuneNo Warranty To Obtain Warranty Service Mitsubishi LCD Flat Panel Hdtv Limited WarrantyThis Limited Warranty does not Cover Network Service Disclaimer WarrantyIndex Digital Audio OutputIndex Page MDEAservice@mdea.com System Reset
Related manuals
Manual 104 pages 28.69 Kb Manual 104 pages 28.69 Kb Manual 40 pages 56.31 Kb

154 Series, 164 Series, 265 Series specifications

Mitsubishi Electronics has established itself as a leader in the HVAC industry, offering a diverse range of products that cater to various needs. Among its notable offerings are the 265 Series, 164 Series, and 154 Series air conditioning units, each embodying advanced technology and user-friendly features.

The Mitsubishi 265 Series stands out for its energy efficiency and environmentally friendly operation. This series employs advanced inverter technology, which adjusts the compressor speed according to the cooling or heating demand, resulting in substantial energy savings. Additionally, the 265 Series is designed with quiet operation in mind, minimizing noise levels for residential and commercial settings. Its compact design allows for easy installation, and it is compatible with a range of indoor units, making it versatile for different applications.

In contrast, the 164 Series focuses on providing effective climate control in larger spaces. This series is equipped with multi-zone capability, allowing a single outdoor unit to connect with multiple indoor units. This flexibility makes it ideal for commercial buildings or residences with varying temperature needs in different areas. The 164 Series also features advanced filtration systems that improve indoor air quality by capturing dust, allergens, and other particles, ensuring a healthier environment.

The 154 Series, on the other hand, is engineered for simplicity and reliability. It is a more basic model designed for users who seek dependable performance without overwhelming features. The 154 Series offers straightforward controls and is easy to operate, making it suitable for both residential and light commercial applications. Despite its simplicity, it still boasts a commendable SEER rating, ensuring energy efficiency while providing comfortable temperature settings.

Across all three series, Mitsubishi Electronics incorporates a range of smart technologies. With compatibility for Wi-Fi control, users can manage their HVAC systems remotely, adjusting temperatures and settings from their smartphones or tablets. This feature enhances convenience and energy management, particularly in modern smart homes.

In summary, the Mitsubishi 265, 164, and 154 Series air conditioning units each offer unique advantages tailored to different consumer needs. From extreme energy efficiency and advanced filtration in the 265 Series to the multi-zone capabilities of the 164 Series, and the reliability of the 154 Series, Mitsubishi Electronics continues to push the boundaries of HVAC technology, ensuring superior comfort and performance in any environment.