Arcam AVR500, AVR600, AV888 Using Zone 2, Extended front panel menu, Updating firmware using a PC

Page 28

Headphones

To use headphones with the unit, plug the headphones into the Phones socket in the centre of the front panel.

When headphones are plugged into the front panel phones socket, the outputs for Zone 1 are muted and the audio will be down-mixed to two channels (2.0). The two-channel down-mix is required so that the centre channel and surround information can be heard via the headphones.

Using Zone 2 and 3

Zone 2 provides the option for the occupants of the master bedroom, conservatory, kitchen, etc. to view or listen to a different source at a different volume level from the main zone (Zone 1).

Zone 3 (AVR600/AV888 only) provides for a third living space to have a copy of the audio signal in Zone 2 at a different volume level.

Extended front panel menu

Pressing the menu key and holding it for longer than four seconds will bring up the Extended Menu, allowing you to perform the following:

Restore to factory defaults

This option allows you to restore all settings on your AVR500/AVR600/AV888 to the defaults that it left the factory with. Note that this also erases any secure backups stored on the unit.

Restore secure backup

Store secure backup

This option allows you to restore from and store to a PIN-protected copy of your settings. The default PIN is 1234.

Change remote code

The default RC5 system code the unit responds to is

16.If required, for example due to another device in your system also using this RC5 system code, it can be changed to 19.

Software versions

Information on the software version of the unit can be found here.

Updating firmware using a PC

Using a PC application (available on request from Arcam), you can update the firmware in your AVR500/ AVR600/AV888 using the back panel RS232 port connected to your PC.

E-26

Page 27 Page 29
Image 28
Page 27 Page 29
Contents AVR500 / AVR600 / AV888 N d b o o k AVR surround amplifier / AV processorSafety Guidelines Important safety instructionsSafety compliance Class II productInstructions de sécurité importantes Class II produitRespect des consignes de sécurité Page Contents Professional Installation?DIY setup? WelcomeBefore you Begin… Power Standby powerPlacing the unit Interconnect cablesTrademark acknowledgements General Making connectionsProduct differences and options Component/RGB Video CompositeAVR600 AV888 Hdmi connectors Zone 3 connectorsComponent/RGB video connectors Zone 2 connectorsConnectors Digital audio Phono Analogue audioTape inputs MCH inputTrigger connectors Infra-red IR connectorsDVD player Satellite receiverCD player Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock Video connectors Component, S-Video and Composite connectors, seeAVR500 Aerials, control and communicationAV, SAT, DVD Subwoofer outputs For more information on connecting speakers, seeFront panel Phones socket Trigger connectors VCR, Camcorder, Games Console etc Preferred video hook-up, in order of preference isConnecting an iPod using the Arcam rDock Radio Connectors Aerial connectors AVR500/AVR600 onlySirius DAB optionConnecting an aerial Other Connectors Data connectors Network connectors USB connectorRS232 serial connector RLead/rDockConnecting speakers AVR500 & AVR600 Connecting subwoofersSpeakers Speaker cablesCentre SubwooferFront left and right Surround left and rightSwitching on OperationOperating your AVR500 /AVR600 / AV888 Selecting a sourceUpdating firmware using a PC Using Zone 2Extended front panel menu Front panel Operation Inserting batteries into the remote control CR102 universal remote controllerUsing the remote control Device Mode / Source keys Useful informationControlling other devices Code blink-backIPod commands AMP AMP Device ModeOK selects/play the highlighted file TUN TUN Device Mode DVD DVD Device ModeNetwork commands Highlighted menu on the screenAV AV Device Mode SAT SAT Device ModeMenus PVR PVR Device Mode VCR VCR Device ModeCD CD Device Mode Starts Program modeShift + rcycles through the repeat Options track, disc, etcEssential Setup Speaker typesSpeaker Distances Speaker LevelsAuto speaker Setup Auto speaker setupProblems Using a subwooferSetup menus Navigating the setup menuSelecting the video source VideoSelecting the audio source Input Config Treble BassGeneral Setup Plii Dimension Plii Centre Width Plii PanoramaGeneral information and system controls Is usedAuto Setup Spkr TypesSpkr Distance Spkr LevelsVideo Inputs Video OutputsProgressive scan playback Important points to rememberZone Settings ModeNetwork For Stereo sourcesEnglish Introduction Decoding ModesTwo-channel source modes Multichannel source modes Decoding modesSettings Volume LevellerDolby Volume is a sophisticated new Calibration OffsetEnglish Tuning/Channel Selection Saving and selecting PresetsDeleting Presets Tuner OperationSirius errors Default unlock code isAdd to your subscription OperationNetwork/usb Operation Selecting the playback sourceUSB playback Internet radio stationsExternal Amplifiers Analogue pre-amplifier outputs AVR600/AV888 onlyEnglish XLR balanced line outputs AV888 only SW2, SW3Multi-room Set up ZoneZone 3 AVR600/AV888 only Zone 2 and 3 control outputsMulti-room connection guide Zone EnglishCustomising CR102 Code LearningCreating Macros Volume punch-throughKey Mover Mode Mover Locking/Unlocking a specific Device ModeTo restore a moved Device Mode key to its original state Copy a key between Device ModesMode key IR punch-through Resetting the CR102Problem Check that Volume is always too loud When I turn onSwitched off Wired networkSpecifications Continual improvement policyProduct Guarantee Worldwide GuaranteeClaims under guarantee Problems?Device code Tables HCM ICEIRT ITCRFT SBRSEG SEIAVP GPXKEC KLHADB NTLUPC DKKCAT CGVDCE ENGAsci SKY+TPS UECYES SH222E Issue
Related manuals
Manual 74 pages 48.95 Kb Manual 68 pages 17.1 Kb Manual 68 pages 27.09 Kb

AV888, AVR500, AVR600 specifications

The Arcam AVR600 is a high-performance AV receiver that is designed for audiophiles and home cinema enthusiasts who seek a premium audio and video experience. This receiver stands out with its array of features and technologies that elevate sound quality and user experience.

At the heart of the AVR600 is its high-fidelity amplification system. The receiver is equipped with a robust 7-channel amplification setup, delivering a total output of 120 watts per channel into 8 ohms. This power enables the AVR600 to reproduce dynamic audio with precision, whether it be for movies, music, or gaming. The class G amplifier design offers exceptional efficiency and reduces distortion, ensuring that sound remains clean and focused even at higher volumes.

The AVR600 boasts extensive connectivity options to accommodate various audio and video sources. It features multiple HDMI inputs and outputs supporting 3D video and 4K scaling, providing flexibility for connecting modern devices. The unit also includes analog and digital inputs, a dedicated phono input for vinyl enthusiasts, and support for multi-room audio setups. With its built-in Bluetooth and network streaming capabilities, users can easily access high-resolution audio files from their digital libraries or popular streaming services.

One of the key technologies in the AVR600 is its advanced room correction system, known as Dirac Live. This sophisticated calibration tool analyzes the acoustics of the room and automatically adjusts the output of the receiver to compensate for any sound anomalies. As a result, listeners experience optimized sound tailored to their specific environment, enhancing the overall listening experience.

For video performance, the AVR600 supports a range of formats, including Dolby Atmos and DTS:X, ensuring an immersive home theater experience with enveloping surround sound. It also features advanced video processing capabilities, allowing users to upscale standard-definition and high-definition content to near 4K quality, further enhancing picture clarity.

In terms of user interface, the AVR600 provides an intuitive on-screen display and a well-designed remote control that makes navigating through settings and options seamless. The receiver is also compatible with smartphone apps for additional convenience, allowing users to control playback and settings directly from their mobile devices.

Overall, the Arcam AVR600 is a versatile audio-visual receiver that combines power, connectivity, and advanced technologies to create an exceptional home entertainment experience. Its unique blend of performance and flexibility makes it an excellent choice for those looking to invest in high-quality audio and video solutions for their homes.
Top Page Image Contents