Arcam AV888, AVR600, AVR500 manual Problem Check that

Page 62

trouble­ shooting

Problem

Check that...

There are no lights on the unit

< the power cord is plugged into the unit and the mains socket it is plugged

 

into is switched on.

 

< the power button is pressed in.

 

If a red LED is present, the unit is in standby mode. Press any button on the

 

front panel or remote control.

The unit responds erratically

< there are fresh batteries in the remote control.

or not at all to the remote

< the front panel window is visible and you are pointing the remote control

control

towards it.

 

The front panel display is

< the display hasn’t been turned off. Press the DISPLAY button on the front

blank

panel or remote control.

No picture is being produced

< your viewing device is turned on and switched to display your AVR500/

 

AVR600/AV888. Test by pressing the MENU button on the AVR500/AVR600/

 

AV888 or on the remote and look for the main menu screen on your display

 

device.

 

< the correct video input is selected on the AVR500/AVR600/AV888.

 

< the video source is on, is operating normally, and is in ‘play’ mode if

 

appropriate.

 

< you have the AVR500/AVR600/AV888 in a video resolution that is

 

compatible with the connection you are using and with your display device.

 

For example, composite video is only capable of carrying 480i and 576i

 

resolutions. Test this by pressing and holding the OK key for more than two

 

seconds to force 480i / 576i output resolutions.

There are bright edges or

< the cables used for analogue video connections are designed to carry video

‘ghosts’ on the picture

(i.e., they are 75Ω coaxial cables).

 

< ensure the ‘sharpness’ control on your display device is switched off or set to

 

near minimum.

 

< for HDMI connections, try using a shorter cable or alternatively a different

 

brand.

No sound is produced

< the correct input has been selected.

 

< the source equipment is on, is operating normally and is in ‘play’ mode if

 

appropriate.

 

< the volume is turned up to a reasonable level and the unit is not in mute

 

mode.

The sound is poor or distorted

< you have not excessively increased the input sensitivity (i.e. reduced the

 

maximum input signal voltage) in the Input Config. menu if an analogue

 

input is being used.

 

< you have selected the correct size of speakers to suit your system in the setup

 

menu.

E-60

Page 61 Page 63
Image 62
Page 61 Page 63
Contents AVR500 / AVR600 / AV888 N d b o o k AVR surround amplifier / AV processorSafety compliance Safety GuidelinesImportant safety instructions Class II productRespect des consignes de sécurité Class II produitInstructions de sécurité importantes Page DIY setup? ContentsProfessional Installation? WelcomeBefore you Begin… Placing the unit PowerStandby power Interconnect cablesTrademark acknowledgements Product differences and options GeneralMaking connections Component/RGB Video CompositeAVR600 AV888 Component/RGB video connectors Hdmi connectorsZone 3 connectors Zone 2 connectorsTape inputs ConnectorsDigital audio Phono Analogue audio MCH inputTrigger connectors Infra-red IR connectorsCD player DVD playerSatellite receiver Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock AVR500 Video connectorsComponent, S-Video and Composite connectors, see Aerials, control and communicationAV, SAT, DVD Front panel Phones socket For more information on connecting speakers, seeSubwoofer outputs Trigger connectors VCR, Camcorder, Games Console etc Preferred video hook-up, in order of preference isConnecting an iPod using the Arcam rDock Sirius Radio ConnectorsAerial connectors AVR500/AVR600 only DAB optionConnecting an aerial RS232 serial connector Other ConnectorsData connectors Network connectors USB connector RLead/rDockSpeakers Connecting speakers AVR500 & AVR600Connecting subwoofers Speaker cablesFront left and right CentreSubwoofer Surround left and rightOperating your AVR500 /AVR600 / AV888 Switching onOperation Selecting a sourceExtended front panel menu Using Zone 2Updating firmware using a PC Front panel Operation Using the remote control CR102 universal remote controllerInserting batteries into the remote control Device Mode / Source keys Useful informationControlling other devices Code blink-backOK selects/play the highlighted file AMP AMP Device ModeIPod commands Network commands TUN TUN Device ModeDVD DVD Device Mode Highlighted menu on the screenMenus SAT SAT Device ModeAV AV Device Mode PVR PVR Device Mode VCR VCR Device ModeShift + rcycles through the repeat CD CD Device ModeStarts Program mode Options track, disc, etcSpeaker Distances Essential SetupSpeaker types Speaker LevelsProblems Auto speaker SetupAuto speaker setup Using a subwooferSetup menus Navigating the setup menuSelecting the audio source VideoSelecting the video source Input Config Treble BassGeneral information and system controls General SetupPlii Dimension Plii Centre Width Plii Panorama Is usedSpkr Distance Auto SetupSpkr Types Spkr LevelsProgressive scan playback Video InputsVideo Outputs Important points to rememberNetwork Zone SettingsMode For Stereo sourcesEnglish Two-channel source modes Decoding ModesIntroduction Multichannel source modes Decoding modesDolby Volume is a sophisticated new SettingsVolume Leveller Calibration OffsetEnglish Deleting Presets Tuning/Channel SelectionSaving and selecting Presets Tuner OperationAdd to your subscription Sirius errorsDefault unlock code is OperationUSB playback Network/usb OperationSelecting the playback source Internet radio stationsEnglish XLR balanced line outputs AV888 only External AmplifiersAnalogue pre-amplifier outputs AVR600/AV888 only SW2, SW3Zone 3 AVR600/AV888 only Multi-room Set upZone Zone 2 and 3 control outputsMulti-room connection guide Zone EnglishCustomising CR102 Code LearningKey Mover Volume punch-throughCreating Macros To restore a moved Device Mode key to its original state Mode MoverLocking/Unlocking a specific Device Mode Copy a key between Device ModesMode key IR punch-through Resetting the CR102Problem Check that Switched off Volume is always too loudWhen I turn on Wired networkSpecifications Continual improvement policyClaims under guarantee Product GuaranteeWorldwide Guarantee Problems?Device code Tables IRT HCMICE ITCSEG RFTSBR SEIKEC AVPGPX KLHUPC ADBNTL DKKDCE CATCGV ENGTPS AsciSKY+ UECYES SH222E Issue
Related manuals
Manual 74 pages 48.95 Kb Manual 68 pages 17.1 Kb Manual 68 pages 27.09 Kb

AV888, AVR500, AVR600 specifications

The Arcam AVR600 is a high-performance AV receiver that is designed for audiophiles and home cinema enthusiasts who seek a premium audio and video experience. This receiver stands out with its array of features and technologies that elevate sound quality and user experience.

At the heart of the AVR600 is its high-fidelity amplification system. The receiver is equipped with a robust 7-channel amplification setup, delivering a total output of 120 watts per channel into 8 ohms. This power enables the AVR600 to reproduce dynamic audio with precision, whether it be for movies, music, or gaming. The class G amplifier design offers exceptional efficiency and reduces distortion, ensuring that sound remains clean and focused even at higher volumes.

The AVR600 boasts extensive connectivity options to accommodate various audio and video sources. It features multiple HDMI inputs and outputs supporting 3D video and 4K scaling, providing flexibility for connecting modern devices. The unit also includes analog and digital inputs, a dedicated phono input for vinyl enthusiasts, and support for multi-room audio setups. With its built-in Bluetooth and network streaming capabilities, users can easily access high-resolution audio files from their digital libraries or popular streaming services.

One of the key technologies in the AVR600 is its advanced room correction system, known as Dirac Live. This sophisticated calibration tool analyzes the acoustics of the room and automatically adjusts the output of the receiver to compensate for any sound anomalies. As a result, listeners experience optimized sound tailored to their specific environment, enhancing the overall listening experience.

For video performance, the AVR600 supports a range of formats, including Dolby Atmos and DTS:X, ensuring an immersive home theater experience with enveloping surround sound. It also features advanced video processing capabilities, allowing users to upscale standard-definition and high-definition content to near 4K quality, further enhancing picture clarity.

In terms of user interface, the AVR600 provides an intuitive on-screen display and a well-designed remote control that makes navigating through settings and options seamless. The receiver is also compatible with smartphone apps for additional convenience, allowing users to control playback and settings directly from their mobile devices.

Overall, the Arcam AVR600 is a versatile audio-visual receiver that combines power, connectivity, and advanced technologies to create an exceptional home entertainment experience. Its unique blend of performance and flexibility makes it an excellent choice for those looking to invest in high-quality audio and video solutions for their homes.
Top Page Image Contents