Arcam AVR500 Placing the unit, Power, Interconnect cables, Radio interference, Standby power

Page 7

Placing the unit

<Place the unit on a level, firm surface, avoiding direct sunlight and sources of heat or damp.

<Do not place the unit on top of a power amplifier or other source of heat.

<Do not place the unit in an enclosed space such as a bookcase or closed cabinet unless there is good provision for ventilation. The unit will run warm during normal operation.

<Do not place any other component or item on top of the amplifier as this may obstruct airflow around the heat-sink, causing the amplifier to run hot. (The unit placed on top of the amplifier would become hot, too.)

<Make sure the remote-control receiver on the front panel display is unobstructed, otherwise this will impair the use of the remote-control. If line-of-sight is impractical, a remote-control repeater can be used with the rear panel connector (see page 17).

<Do not place your record deck on top of this unit. Record decks are very sensitive to the noise generated by mains power supplies which will be heard as a background ‘hum’ if the record deck is too close.

Power

The amplifier is supplied with a moulded mains plug already fitted to the lead. Check that the plug supplied fits your supply – should you require a new mains lead, please contact your Arcam dealer.

If your mains supply voltage or mains plug is different, please contact your Arcam dealer immediately.

The amplifier can be switched for operation between 195–265V (switch position 230V) and 85–132V (switch position 115V).

NOTE

Ensure that the unit is switched off and the power lead removed before changing the position of the voltage range switch.

Push the IEC plug end of the power cable into the socket on the back of the amplifier, making sure that it is pushed in firmly. Plug the other end of the cable into your mains socket and, if necessary, switch the socket on.

The amplifier can be turned on using the power switch on the front panel. While switched on, the front panel LED will glow green.

Standby power

The unit can be switched into standby mode using the 2 button on the CR102 remote control. While in standby mode the front panel LED will glow red and power consumption is around 3 watts.

While in Standby mode, it may be possible to hear a slight residual hum coming from the mains transformer inside the amplifier. This is perfectly normal. However, if the unit is to be left unused for an extended period, we recommend that you disconnect it from the mains supply to save power.

Interconnect cables

We recommend the use of high-quality screened cables that are designed for the particular application. Other cables will have different impedance characteristics that will degrade the performance of your system (for example, do not use cabling intended for video use to carry audio signals). All cables should be kept as short as is practically possible.

It is good practice when connecting your equipment to make sure that the mains power-supply cabling is kept as far away as possible from your audio cables. Failure to do so may result in unwanted noise in the audio signals.

For information on speaker cabling, please refer to the ‘Speakers’ section, beginning on page 23.

Radio interference

The AVR500, AVR600 and AV888 are audio devices containing microprocessors and other digital electronics. They have been designed to very high standards of electromagnetic compatibility.

This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

If the unit causes interference to radio or television reception (which can be determined by switching the unit off and on), the following measures should be taken:

<Re-orient the receiving antenna or route the antenna cable of the affected receiver as far as possible from the unit and its cabling.

<Relocate the receiver with respect to the unit.

<Connect the affected device and the unit to different mains outlets.

If the problem persists, please contact your Arcam dealer.

English

E-5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents N d b o o k AVR surround amplifier / AV processor AVR500 / AVR600 / AV888Class II product Safety GuidelinesImportant safety instructions Safety complianceInstructions de sécurité importantes Class II produitRespect des consignes de sécurité Page Welcome ContentsProfessional Installation? DIY setup?Before you Begin… Interconnect cables PowerStandby power Placing the unitTrademark acknowledgements Component/RGB Video Composite GeneralMaking connections Product differences and optionsAVR600 AV888 Zone 2 connectors Hdmi connectorsZone 3 connectors Component/RGB video connectorsMCH input ConnectorsDigital audio Phono Analogue audio Tape inputsInfra-red IR connectors Trigger connectorsUse the Composite connection if Hdmi DVD playerSatellite receiver CD playerConnecting an iPod using the Arcam rDock Aerials, control and communication Video connectorsComponent, S-Video and Composite connectors, see AVR500AV, SAT, DVD Subwoofer outputs For more information on connecting speakers, seeFront panel Phones socket Trigger connectors Preferred video hook-up, in order of preference is VCR, Camcorder, Games Console etcConnecting an iPod using the Arcam rDock DAB option Radio ConnectorsAerial connectors AVR500/AVR600 only SiriusConnecting an aerial RLead/rDock Other ConnectorsData connectors Network connectors USB connector RS232 serial connectorSpeaker cables Connecting speakers AVR500 & AVR600Connecting subwoofers SpeakersSurround left and right CentreSubwoofer Front left and rightSelecting a source Switching onOperation Operating your AVR500 /AVR600 / AV888Updating firmware using a PC Using Zone 2Extended front panel menu Front panel Operation Inserting batteries into the remote control CR102 universal remote controllerUsing the remote control Useful information Device Mode / Source keysCode blink-back Controlling other devicesIPod commands AMP AMP Device ModeOK selects/play the highlighted file Highlighted menu on the screen TUN TUN Device ModeDVD DVD Device Mode Network commandsAV AV Device Mode SAT SAT Device ModeMenus VCR VCR Device Mode PVR PVR Device ModeOptions track, disc, etc CD CD Device ModeStarts Program mode Shift + rcycles through the repeatSpeaker Levels Essential SetupSpeaker types Speaker DistancesUsing a subwoofer Auto speaker SetupAuto speaker setup ProblemsNavigating the setup menu Setup menusSelecting the video source VideoSelecting the audio source Treble Bass Input ConfigIs used General SetupPlii Dimension Plii Centre Width Plii Panorama General information and system controlsSpkr Levels Auto SetupSpkr Types Spkr DistanceImportant points to remember Video InputsVideo Outputs Progressive scan playbackFor Stereo sources Zone SettingsMode NetworkEnglish Introduction Decoding ModesTwo-channel source modes Decoding modes Multichannel source modesCalibration Offset SettingsVolume Leveller Dolby Volume is a sophisticated newEnglish Tuner Operation Tuning/Channel SelectionSaving and selecting Presets Deleting PresetsOperation Sirius errorsDefault unlock code is Add to your subscriptionInternet radio stations Network/usb OperationSelecting the playback source USB playbackSW2, SW3 External AmplifiersAnalogue pre-amplifier outputs AVR600/AV888 only English XLR balanced line outputs AV888 onlyZone 2 and 3 control outputs Multi-room Set upZone Zone 3 AVR600/AV888 onlyZone English Multi-room connection guideCode Learning Customising CR102Creating Macros Volume punch-throughKey Mover Copy a key between Device Modes Mode MoverLocking/Unlocking a specific Device Mode To restore a moved Device Mode key to its original stateResetting the CR102 Mode key IR punch-throughProblem Check that Wired network Volume is always too loudWhen I turn on Switched offContinual improvement policy SpecificationsProblems? Product GuaranteeWorldwide Guarantee Claims under guaranteeDevice code Tables ITC HCMICE IRTSEI RFTSBR SEGKLH AVPGPX KECDKK ADBNTL UPCENG CATCGV DCEUEC AsciSKY+ TPSYES SH222E Issue
Related manuals
Manual 74 pages 48.95 Kb Manual 68 pages 17.1 Kb Manual 68 pages 27.09 Kb

AV888, AVR500, AVR600 specifications

The Arcam AVR600 is a high-performance AV receiver that is designed for audiophiles and home cinema enthusiasts who seek a premium audio and video experience. This receiver stands out with its array of features and technologies that elevate sound quality and user experience.

At the heart of the AVR600 is its high-fidelity amplification system. The receiver is equipped with a robust 7-channel amplification setup, delivering a total output of 120 watts per channel into 8 ohms. This power enables the AVR600 to reproduce dynamic audio with precision, whether it be for movies, music, or gaming. The class G amplifier design offers exceptional efficiency and reduces distortion, ensuring that sound remains clean and focused even at higher volumes.

The AVR600 boasts extensive connectivity options to accommodate various audio and video sources. It features multiple HDMI inputs and outputs supporting 3D video and 4K scaling, providing flexibility for connecting modern devices. The unit also includes analog and digital inputs, a dedicated phono input for vinyl enthusiasts, and support for multi-room audio setups. With its built-in Bluetooth and network streaming capabilities, users can easily access high-resolution audio files from their digital libraries or popular streaming services.

One of the key technologies in the AVR600 is its advanced room correction system, known as Dirac Live. This sophisticated calibration tool analyzes the acoustics of the room and automatically adjusts the output of the receiver to compensate for any sound anomalies. As a result, listeners experience optimized sound tailored to their specific environment, enhancing the overall listening experience.

For video performance, the AVR600 supports a range of formats, including Dolby Atmos and DTS:X, ensuring an immersive home theater experience with enveloping surround sound. It also features advanced video processing capabilities, allowing users to upscale standard-definition and high-definition content to near 4K quality, further enhancing picture clarity.

In terms of user interface, the AVR600 provides an intuitive on-screen display and a well-designed remote control that makes navigating through settings and options seamless. The receiver is also compatible with smartphone apps for additional convenience, allowing users to control playback and settings directly from their mobile devices.

Overall, the Arcam AVR600 is a versatile audio-visual receiver that combines power, connectivity, and advanced technologies to create an exceptional home entertainment experience. Its unique blend of performance and flexibility makes it an excellent choice for those looking to invest in high-quality audio and video solutions for their homes.
Top Page Image Contents