Initial settings
SCREEN SAVER
A television monitor screen may be burned out if a static picture is displayed for a long time. To prevent this, the unit automatically activates the screen saver function if a
Speaker setting
Speaker Channel setting
static picture, such as an
Select the speaker configuration type according to your speaker
PREFERENCE1 | PREFERENCE2 | SPK.SETTING |
|
| 5.1 CH. |
|
| LEVEL |
• | MODE 1 |
| The current picture gets |
| dark. |
• | MODE 2 |
| The “screen saver” picture |
| appears and its brightness |
PREFERENCE1 | PREFERENCE2 SPK. SETTING | |
DIGITAL AUDIO OUTPUT | STREAM/PCM | |
DOWN MIX |
| OFF |
COMPRESSION | OFF | |
DTS BASS MANAGEMENT | OFF | |
AUTO STANDBY | OFF | |
SCREEN SAVER | MODE1 | |
AV COMPULINK MODE | DVD1 | |
PRESS | KEY |
|
system. Normally, simply select “5.1 CH.” or “2 CH.”. However, by selecting “EXPERT”, you can make fine tuning to match your speaker system.
|
|
|
| DELAY | |
|
|
|
| F. SP | Large |
|
|
|
| C. SP | Small |
|
|
| |||
|
|
|
| R. SP | Small |
|
|
|
| BASS | S.woofer |
|
|
|
|
| |
PRESS | KEY |
| TEST TONE | ||
changes. |
• OFF |
• 2 CH. |
When you connect to a |
The screen saver function is off.
NOTES
•The monitor screen of a projector or projection TV is easily burned out if a static picture is displayed for a long time. Be careful not to allow the monitor screen to be burned out when you set the SCREEN SAVER mode to “OFF”.
•The TV screen may be garbled when you set the SCREEN SAVER mode to “MODE 1”. In this case, set to another mode.
•When a static picture is displayed for a long time during playback, the screen saver function is always activated in “MODE 1” regardless of whether you select “MODE 1” or “MODE 2”.
AV COMPULINK MODE
• | 5.1 CH. |
| When you connect to a |
| the front, rear, center and |
• | EXPERT |
| When you want to make fine tuning to match your |
| speakers. The following five setting items are |
| available. |
NOTES
• When selecting “5.1 CH.” or “EXPERT”, set “DOWN |
MIX” to “OFF” (see page 58). |
• The Dolby Digital LFE (Low Frequency Effect) signal is |
always fed from the SUBWOOFER output on the rear |
panel of the unit regardless of speaker setting. |
• If you connect the unit's digital output to an external |
Dolby Digital or DTS decoder (and set the “DIGITAL |
AUDIO OUTPUT” option to “STREAM/PCM”), the |
If you use the AV COMPU LINK system, you must set this item correctly.
Select from the three options: “DVD1”, “DVD2” and “DVD3” according to the equipment to be connected.
See page 64.
PREFERENCE1 | PREFERENCE2 | SPK. SETTING | |
DIGITAL AUDIO OUTPUT | STREAM/PCM | ||
DOWN MIX |
|
| OFF |
COMPRESSION |
| OFF | |
DTS BASS MANAGEMENT |
| OFF | |
AUTO STANDBY |
| OFF | |
SCREEN SAVER |
| MODE1 | |
AV COMPULINK MODE |
| DVD1 | |
PRESS | KEY |
|
|
speaker setting above is not effective. Make the speaker |
setting of the external decoder properly. |
Speaker size settings
(available only when selecting EXPERT)
Sets the speaker sizes |
|
|
|
|
according to your | PREFERENCE1 PREFERENCE2 | SPK.SETTING | ||
speakers. |
|
| EXPERT | |
|
| LEVEL | ||
|
|
| DELAY | |
|
|
| F. SP | Large |
|
|
| C. SP | Small |
|
|
| R. SP | Small |
|
|
| BASS | S.woofer |
| PRESS | KEY | TEST TONE | |
Initial settings
1 Select the speaker to be set using CURSOR
5/∞.
•F.SP: Front speakers
•C.SP: Center speaker
•R.SP: Rear speakers
59