Hitachi 42HDX62A Remote Control for Additional Audio Equipment, Precoded Audio Buttons

Page 39

The Remote Control for Additional Audio Equipment

Operating the precoded function for your Audio component.

This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to pages 41-42 for pre-codes).

1.Turn ON your Audio component you wish to control with the Remote.

2.Aim the remote control at the front of your Audio component.

3.To switch to Audio (AMP) component pre-coded

mode, use the SOURCE ACCESS buttons ( or ) on the remote control to position the LED light to the corresponding selection.

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio component, as shown on pages 41-42. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code.

6.The remote will now control your Audio component.

7.Repeat steps 1 - 6 if you wish to program the remote to control another Audio component.

NOTE: 1. If your Audio component cannot be operated after performing the above procedures, your Audio component code has not been precoded into the remote.

2.In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio component operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

PRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio component codes.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

/

MY AUDIO COMPONENT

CODE IS:

NOTE: Refer to instruction manual of the VCR/PVR for operation of the buttons exclusively for the VCR/PVR.

The Remote Control

39

Image 39

Contents Plasma Television Read Before Operating Equipment Important Safety InstructionsFor More INFORMATION, Call 1-800-HITACHI Accessories Remote Control Battery Installation ReplacementFor U.S. models Location How To Set Up Your New Hitachi Plasma TelevisionConnect Power Swivel Cable AntennaAntenna Connections to Rear Jack Panel 10’ 15’Minimum ViewingHook-up Cables and Connectors Mode Indicator Quick Reference Remote Control Buttons and FunctionsFront/Rear/Side Panel Controls Side Input Jacks for Input Power light indicatorRemote Control sensor Learning AV NET sensorRear Panel Connections IR Blaster/G-LINKMonitor OUT & HI-FI Audio OUT IEEE1394 DV Input Upgrade CardTo Power Swivel Connector Subwoofer OutInformation and press the Select button Appendix EBefore Operating External Video Source Connecting External Video SourcesDVI Hdmi Macrovision Notes Tips on Rear Panel ConnectionsConnecting a Video and Stereo Audio Source to INPUT1 INPUT5 DVI to Hdmi Input Hdmi inputSee page 16 for tips on Rear Panel Connections Digital VCR D-VHS Connecting External Audio/Video Devices Connecting AN External Audio AmplifierConnecting Monitor OUT VCR Output C B P R/C R R Automatic Mode Default mode Remote ControlHow to Use the Remote to Control Your TV ZOOM1/ZOOM2 Aspect buttonStandard ExpandedAIR ANALOG/DIGITAL ChannelsPhoto Input Cursor PADRotate When an IEEE1394 device is not connected When an IEEE1394 device is connectedIEEE1394 Dash button Volume VOL WHEEL, Mute buttonLast Channel Last CH button Channel CH WHEEL/CHANNEL Selector buttonsPIP button Picture-in-Picture PIPPIP PIP Mode PICTURE-IN-PICTURESplit Mode PICTURE-IN-PICTURE Surf Mode PICTURE-IN-PICTURESplit Freeze Main FreezeStrobe Freeze Exclusive TV buttons Remote Control for Cable Box FunctionsOperating the precoded function for your cable box Precoded Cable BOX buttonsSET-TOP-BOX Code is Remote Control for Set-Top-Box/Satellite Receiver FunctionsPRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons MY Satellite ReceiverMY DVD Player Code is Remote Control for DVD FunctionsOperating the precoded function for your DVD player Precoded DVD ButtonsRemote for VCR/PVR Functions Precoded VCR/PVR ButtonsMY VCR/PVR Code is MY Audio Component Code is Remote Control for Additional Audio EquipmentOperating the precoded function for your Audio component Precoded Audio ButtonsInput Access How to Use the ENT ButtonVCR Brand Code Remote Control CodesSET TOP BOX BRAND..CODE Simple Remote Control Video On-Screen DisplayTV Guide On Screen Video Use the Cursor PAD Aspect Color DecodingAuto Color White BalanceSet Black Side Panel Reset Video SettingsAudio SRSBBE DRC To Setup the TV Guide On Screen System Setup ProcedureTV Guide On Screen TV Guide On Screen TV Guide On Screen TV Guide On Screen TV Guide On Screen Using the TV Guide On Screen System Guide Navigating the TV Guide on Screen SystemName Description TV Guide On Screen IconsTune to Channel / Watch NOW GO to Service BARCancel ListingsExample Category Search Movies SearchDelete Search Example Keyword SearchTo Edit or Delete a keyword Edit SearchDelete Episode RecordingsResume Play from BeginningEdit Recording ScheduleWatch NOW/TUNE to Channel Delete RecordingHow to Remind Recording ConflictRecording Notification Banner How to set a reminder Select these options SetupReminder Notification Banner Remind Conflict Remind conflict message will appear ifChange Channel Display Change System SettingsRemind Defaults Change Default OptionsGeneral Default Options Record DefaultsIR Defaults Auto Channel Scan Signal MeterStart or Reset option Channel ManagerWhich are your Favorite FAV Channels Channel ListLocks Change Access CodeMotion Picture Ratings Table Movie RatingsTV Ratings Use the Cursor PAD , or ChannelTV Parental Guide Ratings Table Canadian Ratings English Table Canadian Ratings EngCanadian Ratings French Chart Set The Clock TimersSet Sleep Timer Set Day/Night TimerUse the Cursor Pads to select DAY Mode on Setup Menu PreferenceSet the Language Screen Saver Image PowerScreen Saver Picture’s Movement Automatic Power Saving Set the Menu BackgroundSet AV Net AutoRemote OffPress the Select button to start the Setup Wizard AV NET Setup Wizard Example A/V Receiver SetupAV Net Setup Wizard Device Settings AV NET Setup Wizard Example DVD SetupLearning Mode Learning Mode Example A/V Receiver SetupUse the Cursor PAD To select Other from brand name choices AV Net Setup Wizard A/V Receiver Setup Learning Mode Example CUSTOM/DVD 3 SetupPower Menu Select Exit Setup Analog Captions Caption ModeSet Closed Caption Caption DisplayFixed Set Monitor OutMonitor TV Tuner OutUpgrades Upgrade NOWInsert MMC Card Power Swivel Set Stand-By ModeDo not Equipment Care and TroubleshootingTroubleshooting Switch ON/OFF Switch onceReception Problems Troubleshooting Is Help available in the Guide? If so, how do I find it? What do the frequencies for Record and Remind mean?How can I look for a specific show in the Guide? Agency Regulatory Information Useful InfoFeatures Features and SpecificationsSet Dimensions Canada 1-800-HITACHI HitachiHome Electronics Division Digital Media DivisionEND User License Agreement for Hitachi DTV Software End User License Agreement for Hitachi DTV SoftwareImage Input Type Format Aspect Video ID Auto Aspect AppendixesHdmi IndexQR64866