Crown CTS 4200, CTS 8200 operation manual Specifications, Dual Mode

Page 19

CTs Multi-Channel Power Amplifiers

7 Specifications

Figure 7.1

CTs 4200

Power Chart

CTs 4200: MINIMUM GUARANTEED POWER (in watts, 0.1% THD) 120VAC, 60 Hz units

Dual Mode

Channels Driven			4		2		1
		1 kHz		20 Hz - 20 kHz	1 kHz	1 kHz		20 Hz - 20 kHz


4 Ohm		260		215	270	270		225
8 Ohm		200		190	210	220		210
70V ( 25 Ohm) at 0.1% THD		220		220*	240	250		245*
Bridge-Mono Mode
Channel Pairs Driven					2		1
				1 kHz	20 Hz - 20 kHz	1 kHz		20 Hz - 20 kHz


8 Ohm				520	430	560		450
16 Ohm				400	380	440		420
100V (50 Ohm) at 0.1% THD				220	220*	250		245*

* Constant Voltage full bandwidth power ratings support 100 Hz - 20 kHz due to automatic high-pass filters.

Figure 7.2

CTs 8200

Power Chart

CTs 8200: MINIMUM GUARANTEED POWER (In watts, 0.1% THD) 120VAC, 60 Hz units

Dual Mode

Channels Driven			8			4	2		1
		1 kHz		20 Hz - 20 kHz		1 kHz	1 kHz	1 kHz		20 Hz - 20 kHz

4 Ohm		200		175		250	260	270		230
8 Ohm		160		155		190	200	220		220
70V (25 Ohm) at 0.1% THD		200		185*		220	240	250		230*
Bridge-Mono Mode
Channel Pairs Driven					4		2		1
				1 kHz		20 Hz - 20 kHz	1 kHz	1 kHz		20 Hz - 20 kHz


8 Ohm				400		350	500	540		460
16 Ohm				320		310	380	440		440
100V (50 Ohm) at 0.1% THD				200		185*	220	250		230*

* Constant Voltage full bandwidth power ratings support 100 Hz - 20 kHz due to automatic high-pass filters.

Operation Manual

page 19

Image 19

Contents Some models may be exported under the name Amcron CTsCTs Series amplifiers require Class 2 output wiring Important Safety InstructionsOr has been dropped EMC Standards Safety StandardEuropean Representatives Name and Address Family Name CTsAC Power Draw and Thermal Dissipation SetupTroubleshooting SpecificationsProven Crown AB+B Multi-Modeoutput topology How to Use This ManualFeatures WelcomeUnpack Your Amplifier Install Your Amplifier SetupOver 60 ft 18.3 m Choose Input Wire and ConnectorsChoose Output Wire and Connectors Crown recommends using professionally constructed, highDual 70V Mode Wire Your System Dual 8/4 ModeBridge-Mono 100V Mode Bridge-Mono 16/8 ModeConnect to AC Mains Startup ProcedureOperation PrecautionsClip Indicator Front Panel Controls Indicators Bridge Mode IndicatorReady Indicator Signal IndicatorInput Connectors Back Panel Controls Connectors AC Power Cord ConnectorOutput Connectors Accessory PanelAdvanced Features Options Attenuation in dB Channel Level ControlInput Sensitivity Options Control ModulesWall-Mount level control panels for use with VCA module Choosing the Right ModuleRefer to .1.6 for specific voltage requirements TroubleshootingThermal Level Control TLC is active Mode switch was switched while the power was on Power supply thermal overloadDual Mode SpecificationsDimensions Width, Height, Depth Crosstalk below rated power, 20 Hz to 1 kHzCommon Mode Rejection CMR 20 Hz to 1 kHz Power Draw at Idle 120VAC mains, all channels in 70V modeCTs 8200 Typical Frequency Response 1 W CTs 8200 Typical Output Impedance vs. Frequency AC Power Draw and Thermal Dissipation AC Power Draw Thermal DissipationOhms Bridge 320x4 Service 12/01 WarrantyWorldwide Except USA & Canada CTs Multi-Channel Power Amplifiers Nature of Problem Crown Factory Service InformationThis page Intentionally Left Blank CTs Multi-Channel Power Amplifiers