Crown CTS 8200 Welcome, Setup, Troubleshooting, Specifications, Service Operation, Warranty

Page 4

CTs Multi-Channel Power Amplifiers

Important Safety Instructions

2

5.1.3 Fault Isolation Topology (FIT)

14

Declaration of Conformity

3

5.1.4 35-Hz High-Pass Filter

14

1 Welcome

5

5.1.5 AC Under-/Over-Voltage Protection

14

1.1

Features

5

5.1.6 Power Fuse

14

2 How to Use This Manual

5

5.1.7 Inrush Limiting

14

3 Setup

6

5.1.8 Variable-speed Fans

14

3.1

Unpack Your Amplifier

6

5.2 Advanced Features

14

3.2

Install Your Amplifier

6

5.2.1Switching Power Supply

14

3.3

Ensure Proper Cooling

6

5.2.2 Mode Switch

14

3.4

Choose Input Wire and Connectors

7

5.2.3 Bridge Mode Indicator

14

3.5

Choose Output Wire and Connectors

7

5.2.4 Channel Level Control

15

3.6

Wire Your System

8

5.3 Options

16

 

3.6.1 Dual 8/4 Mode

8

5.3.1 Control Modules

16

 

3.6.2 Dual 70V Mode

8

5.3.2 Input Sensitivity

16

 

3.6.3 Bridge-Mono 16/8 Mode

9

6 Troubleshooting

17

 

3.6.4 Bridge-Mono 100V Mode

9

7 Specifications

19

3.7

Connect to AC Mains

10

8 AC Power Draw and Thermal Dissipation

23

3.8

Startup Procedure

10

9 Service

25

4 Operation

11

9.1 Worldwide Service

25

4.1

Precautions

11

9.2 US and Canada Service

25

4.2 Front Panel Controls and Indicators

12

9.2.1 Service at a US or Canada Service Center

25

4.3

Back Panel Controls and Connectors

13

9.2.2 Factory Service

25

5 Advanced Features and Options

14

9.2.3 Factory Service Shipping Instructions:

25

5.1

Protection Systems

14

10 Warranty

26

 

5.1.1 Thermal Level Control (TLC)

14

Crown Factory Service Information Form

29

 

5.1.2 Fault

14

 

 

page 4

Operation Manual

Page 3 Page 5
Image 4
Page 3 Page 5
Contents CTs Some models may be exported under the name AmcronCTs Series amplifiers require Class 2 output wiring Important Safety InstructionsOr has been dropped Safety Standard European Representatives Name and AddressFamily Name CTs EMC StandardsSetup TroubleshootingSpecifications AC Power Draw and Thermal DissipationHow to Use This Manual FeaturesWelcome Proven Crown AB+B Multi-Modeoutput topologySetup Unpack Your Amplifier Install Your AmplifierChoose Input Wire and Connectors Choose Output Wire and ConnectorsCrown recommends using professionally constructed, high Over 60 ft 18.3 mWire Your System Dual 8/4 Mode Dual 70V ModeBridge-Mono 16/8 Mode Bridge-Mono 100V ModeStartup Procedure Connect to AC MainsPrecautions OperationFront Panel Controls Indicators Bridge Mode Indicator Ready IndicatorSignal Indicator Clip IndicatorBack Panel Controls Connectors AC Power Cord Connector Output ConnectorsAccessory Panel Input ConnectorsAdvanced Features Options Channel Level Control Attenuation in dBOptions Control Modules Wall-Mount level control panels for use with VCA moduleChoosing the Right Module Input SensitivityRefer to .1.6 for specific voltage requirements TroubleshootingThermal Level Control TLC is active Power supply thermal overload Mode switch was switched while the power was onSpecifications Dual ModeCrosstalk below rated power, 20 Hz to 1 kHz Common Mode Rejection CMR 20 Hz to 1 kHzPower Draw at Idle 120VAC mains, all channels in 70V mode Dimensions Width, Height, DepthCTs 8200 Typical Frequency Response 1 W CTs 8200 Typical Output Impedance vs. Frequency AC Power Draw Thermal Dissipation AC Power Draw and Thermal DissipationOhms Bridge 320x4 Service Warranty 12/01Worldwide Except USA & Canada CTs Multi-Channel Power Amplifiers Crown Factory Service Information Nature of ProblemThis page Intentionally Left Blank CTs Multi-Channel Power Amplifiers
Top Page Image Contents