Extron electronic MLC 52 manual Programming video inputs projector remote control type B

Page 58

Special Applications, cont’d

Programming video inputs — projector remote control type B

1. Place the rear panel configuration DIP switch #1 in the On (up) position to enable learning mode. (If the MLC is already in learning mode, proceed to step 2.)

ON
1	2	3	4

2. Using IR learning, program command “A” from the Video input selection button on the projector’s remote control into memory block #1 of the MLC 52’s Video or blank (for VC models) button as follows:

a. Press the Video button on the MLC front panel. The button blinks, indicating that the MLC is ready to learn the command. On the rear panel, the bottom IR learning LED flashes.

b. Within 5 seconds (while the Video button on the MLC 52 is blinking), press the Video button on the projector’s remote control. The MLC has learned command “A” for Video.

When a command has been successfully learned, the IR learning LEDs on the MLC rear panel flash in rapid progression from the top to the bottom, then back to the top.

3. Program the input selection command “B” from the Video input selection button on the projector’s remote control into memory block #2 of the MLC 52’s Video button as follows:

a. Press the Video button on the MLC front panel. The button blinks, indicating that the MLC is ready to learn the command. On the rear panel, the second LED from the bottom flashes.

b. Within 5 seconds (while the Video or blank button on the MLC 52 is blinking), press the Video button on the projector’s remote control. The MLC has learned command “B” for Video.

4. When finished programming the MLC 52 buttons, return configuration DIP switch #1 to its Off (down) position.

5. Test the system.

	DISPLAY
ON	OFF
VOL	PC
VOL
VOL	VIDEO
	VIDEO

Command #1: RGB / IR Command “A”

Command #2: RGB / IR Command “B”

Command #1: Video / IR Command “A”

Command #2: Video / IR Command “B”

COMPUTER		VIDEO
VIDEO	AUDIO	A/V
MUTE	MUTE	MUTE
MENU		ENTER

CONT/ COL/

SIZE CENTER BRT TINT

SHARP	PHASE	ASPECT
		RATIO

MLC 52

Projector Remote Type B

Programming MLC 52 input selection buttons from a projector remote control type B

4-14 MLC 52 Series MediaLink Controllers • Special Applications

Image 58

Contents MLC 52 Series MediaLink ControllersSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolTable of Contents Table of Contents, cont’d Entering display device communications port settings MLC 52 Series MediaLink Controllers Table of Contents IiiAppendix a Specifications, Part Numbers, and Accessories Iv MLC 52 Series MediaLink Controllers Table of ContentsOne About the MLC 52 Series Features and OptionsStandard features MLC 52 Series MediaLink Controllers IntroductionOptions and accessories Application diagram for a standard MLC 52 1-gang size MLC 52 Application ExamplesTwo Installation Overview MLC 52 Series MediaLink Controllers InstallationPreparing the site and installing the wall box Installation ProceduresUL Requirements Replacing the faceplate Screws to remove from the MLC faceplateReplacing button labels Installing the MLC onto a new faceplate bottom viewReplacing a button label Mounting an electrical box Attaching a wall box to a wall stud MLC 52 rear view Rear panel and cable connectionsMLC 52 VC rear view MLC 52 Series MediaLink Controllers Installation Wiring the control connector Pinout guide for the MLC 52 display/source control connectorWiring for IR control Wiring the control connector for IRWiring an IR Link Wiring for RS-232 control RS models onlyWiring for RS-232 control RS models only UC 50, 100, and 200 cable color codesWiring and using the IR Link for IR remote control Wiring an IRL Wiring an IRLConnecting the MLC 52 to the external power supply Wiring the power connectorWiring the VC port Mounting the MLC to an electrical box or mounting bracket Mounting the MLCMounting the MLC 52 in a wall box Mounting the MLC 52 to a mounting bracket mud ring Mounting the MLC to a wall or furnitureInstallation, cont’d Three Display Device Control Front Panel Features and OperationSwitch modes Buttons on the front panelFront panel components MLC 52 front panelMm connector cable for the configuration port Operation, cont’dConfiguring the MLC 52 Using IR Order in which the buttons blink during data transfer Configuring using IR learning Percent Complete MLC MLC 52 VC Models Buttons LitActivation of LEDs during button configuring Removing commands from a button Setting up button macrosConfiguring a single button for input source selection Requirements for the MLC 52 VC with volume control knob Extron MPAConfiguring the MLC 52 IR and MLC 52 RS Vol buttons Powering the Display Device On and OffWiring and connections for the MLC 52 VC models Powering onSelecting Inputs Powering offInput selection buttons on the MLC 52 front panel Operating the MLC 52 Using IR Remote Control Using the IR Link with the MLC 52 and the IRButtons on the IR 452 remote control MLC 52 configuration cannot be performed from the IRLocking the Front Panel Executive Mode ResettingButtons to press and hold for executive mode Four Application 1 Projector with more than two inputs Application 1 Using Multiple Sources with an MLCMLC 52 Series MediaLink Controllers Special Applications Projector remote control type a application Examples of projector remote control types a and BProgramming buttons for an IR controlled system Special Applications, cont’d Volume OFF Projector remote control type B application Command #1 Computer Command #2 VideoApplication 2 Projector Requiring a Power Off Confirmation Typical projector power off confirmation promptConfiguring the MLC 52 for a power-off confirmation Configuring the MLC 52 for multi-coded IR functionality Programming RGB inputs projector remote control type aProgramming video inputs projector remote control type a Display Using the PC button RGB Programming VC models projector remote control type aProgramming RGB inputs projector remote control type B Programming video inputs projector remote control type B Using the Video button S-video or composite video Programming VC models Projector remote control type BSpecial Applications, cont’d Five RS-232 configuration cable pin assignments Using the MLC 52 Configuration ProgramMLC 52 Series MediaLink Controllers Serial Communication Installing the software Extron Software Products Disc a screenStarting the configuration program Configuration Wizard screenLoading the serial RS-232 drivers Loading Extron driversLoading the IR drivers Selecting the MLC 52 / Dvcm 50 IR driver package IR driver package list Viewing the IR driver package versionChanging the location of the IR drivers IR driver information in the Help Details windowIR Driver Directory window Browse For Folder window Configuring using the MLC 52 Configuration WizardKey to file names File name DescriptionInitial configuration options screen Select Initial Option screen, first radio button selectedCreating a new configuration using the wizard Select COM Port screen Select MediaLink Serial Driver screen for RS modelsSelect IR Driver screen for IR models IiiSerial Communication, cont’d Assign Commands To Buttons window with PC button selected To add a command to a buttonOverwrite prompt Uploading an existing configuration using the wizard Select Configuration File screen RS versionClick Next Configuring using the Windows-based configuration program Wizard Finish screenOverview of the configuration procedure Opening the MLC 52 Configuration Program screenMode selection window, Select a Comm Port tab Model selection screenMLC 52 Configuration Program screen not configured File menu, Save Configuration as... selected Saving and restoring a configurationSaving a configuration Displaying the Help programRestoring a configuration Save configuration to... windowSave Configuration prompt Load configuration from... window Overview of the MLC 52 configuration program main screenMain screen with a driver added Menu barTrace Window example Help menuAbout window from Help menu, showing an MLC 52 RS Details window from the Help menuFront panel representations Display settings tabs Button Settings areaButton Operations area Add Driver window Adding a driverSerial driver overwrite prompt Select Your IR Driver window Select a serial driver... windowAuto Fill window Removing a serial driver Removing a driverRemoving an IR driver Assigning functions to buttonsCommand added to the first memory block of the PC button PC button selected on MLC 52 main screenAssigning user-defined functions to buttons Button Operations section containing a user-defined codeSetting up button modes and labels User-defined command entered for Video buttonRemoving a function from a button Serial Communication, cont’d Factory defaults Entering display device power settings Setting the button modesSwitch Mode menu for a volume button Display Power Settings tabNo IR/232 while display power is off Entering display device communications port settingsProgramming the MLC 52 for control by the IR 452 Remote Performing IR learning via softwarePrompt to press IR remote control button IR learning readiness promptPlaying an IR command IR learning timeout promptPlaying an IR command Using emulation modeConnection window with Emulation Mode tab selected Existing configurations dropdown menu on Connection Window Device selection screen for emulation mode Selecting the starting screen Wizard Options submenuFile menu, Total Factory Reset selected ResettingReset to factory defaults confirmation prompt Uploading firmware MLC 52 main screen after reset standard modelDownloading the firmware from the Web Updating the firmware Installing the Firmware LoaderExtron’s Firmware Loader window Selecting the firmware on the Choose Firmware File window Firmware Loader windowHost-to-MLC communications Using Simple Instruction Set SIS CommandsAscii to Hex conversion table Symbol definitions Command/response table for SIS commands Command Hexadecimal Response Additional Send/receive data to/from page 0 memoryAAppendix a Specifications, Part Numbers, and Accessories SpecificationsIncluded parts Part Numbers and AccessoriesIncluded parts Part number Optional accessories CablesAppendixBB MLC 52 IR and MLC 52 RS cutout template MLC 52 IR and MLC 52 RS TemplateMLC 52 Series MediaLink Controllers Templates MLC 52 IR VC and MLC 52 RS VC Template MLC 52 IR VC and MLC 52 RS VC cutout templateTemplates, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C

Related manuals

Manual 74 pages 53.93 Kb