Hitachi CP-X440 Related messages, Time the lamp timer has counted is approaching 2000 hours

Page 42

Troubleshooting

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below. If the same message is displayed after the remedy, or if a message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

CHANGE THE LAMP.

AFTER REPLACING LAMP, RESET THE LAMP TIMER.

CHANGE THE LAMP.

AFTER REPLACING LAMP, RESET THE LAMP TIMER.

THE POWER WILL BE

TURNED OFF ** hrs later.

CHANGE THE LAMP.

AFTER REPLACING LAMP, RESET THE LAMP TIMER.

THE POWER WILL BE

TURNED OFF 0 hrs later.

Description

The time the lamp timer has counted is approaching 2000 hours.

Preparation of a new lamp and an early lamp change are recommended. After you have changed the lamp, please be sure to reset the lamp timer(36).

The time the lamp timer has counted is approaching 2000 hours, so a lamp change within ** hours is recommended.

When lamp usage reaches 2000 hours, the power will automatically be turned off. Please change the lamp by referring to the section “Lamp”. After you have changed the lamp, please be sure to reset the lamp timer(36).

As the time the lamp timer has counted has reached 2000 hours, the power will soon be automatically turned off.

Please immediately turn the power off, and change the lamp by referring to the section “Lamp”. After changing the lamp, please be sure to reset the lamp timer(36).

NO INPUT IS DETECTED

ON ***

There is no input signal.

Please confi rm the signal input connection, and the status of the signal source.

SYNC IS OUT OF RANGE

ON *** fH *****kHz fV *****Hz

The horizontal or vertical wavelength of the input signal is out of the response parameter range of this unit.

Please confi rm the specs for your projector or the signal

source specs.

42

Image 42
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Power on/off Setting upRemote control MaintenanceAbout contents of package Fastening the lens cover CB/PB ProjectorComponent CR/PRRemote control Control buttonsMagnify Setting up Arrangement For the model CP-X444For the model CP-X440 Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityConnecting to a monitor output Connecting to a speaker with amplifier outputExamples of connection with a computer Video out Audio L out Examples of connection with a VCR/DVD playerAudio/Video cable Audio R outConnecting power supply Remote control Putting batteriesUsing the remote control Turning off the power Power on/offTurning on the power PowerOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound For an RGB signal Searching an input signalAdjusting the zoom and focus  For a video signal/no signal For a video signal or s-video signal Using the automatic adjustment featureAdjusting the position  For a component video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenMultifunctional settings Using the menu functionAdvanced Menu Aspect Mode Brightness Contrast Color Tint Shrpness Whisper Easy MenuDescription Mirror Reset Filter Time Language Easy MenuGo To Advanced Menu Description #3 Custom  #3 Default  #2 Custom Picture MenuGamma High  Middle  LOW  Custom Picture MenuColor Temp Color Tint SharpnessProgressive MY Memory TV  Film  Turn OFFLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1 For a video signal / no signal 43  169  Small Aspect Over Scan Position H Position PhaseFor an RGB signal Image MenuSize Auto Adjust Execute For a video signal or s-video signalImage Menu Component  Scart RGB Input MenuColor Space Component Video Format Auto  Ntsc  PAL  SecamInput Menu InformationSetup Menu Whisper Mirror VolumeAudio Screen Menu Menu Position OSD Bright BlankBright  Dark MyScreen MyScreen Lock Description Screen MenuStart UP Turn on  Turn OFFMessage No Input is Detected Sync is OUT of RangeAuto Search Auto OFF Lamp Time Filter Time Reset  CancelOption Menu RGB IN1  RGB IN2  Component Video  S-VIDEO  VideoOption Menu Maintenance LampCase of replacement by yourself LampAir filter Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensTime the lamp timer has counted is approaching 2000 hours There is no input signalRelated messages Internal temperature is rising Related messagesPossibility that interior portion has become Regarding the indicator lampsLamp does not light, and there is a HeatedCooling fan is not operating Regarding the indicator lampsIt is time to clean the ai r filter There is a possibility that the interior portionSignal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Volume is adjusted to an extremely low levelColor Space setting is not suitable Brightness is adjusted to an extremely low levelColor settings are not correctly adjusted Lens cap is attachedRGB output SpecificationRGB input Audio inputFor the model CP-X444 For the model CP-X440 SpecificationsExample of computer signal Vesa TextVesa Initial set signals Connection to the ports RGB in 1, B RGB in 2, C RGB OUTComponent Video D Y, E CB/PB F CR/PR Audio 1-IN Ø3.5 stereo mini jack, I J Audio 2 L/R RCA jack RTSCTS Connecting the cable Communications settingRS-232C Communication Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Keystone Mute OSD Bright Hitachi Atago Building
Related manuals
Manual 2 pages 63.85 Kb Manual 2 pages 62.14 Kb

CP-X444, CP-X440 specifications

The Hitachi CP-X440, CP-X444, and CP-X445 projectors are part of Hitachi's highly regarded line of portable projectors designed for professional presentations, educational environments, and corporate meetings. With their robust performance and user-friendly features, these projectors stand out as reliable tools for a variety of applications.

One of the key features of the CP-X440, CP-X444, and CP-X445 is their impressive brightness levels. Equipped with high-lumen output capabilities, these projectors ensure vibrant and clear images even in well-lit environments. With brightness ratings of up to 4000 ANSI lumens, they can effectively project content onto large screens or walls, making them suitable for classrooms, conference rooms, and auditoriums.

Resolution is another critical aspect of these projectors. The CP-X440, CP-X444, and CP-X445 support native XGA resolution (1024 x 768 pixels), providing sharp and detailed images that enhance the viewing experience. This resolution is ideal for displaying presentations, charts, and videos, ensuring that the audience can easily read and understand the content.

In terms of connectivity, these projectors offer a wide range of options to accommodate various devices. They come with multiple input terminals, including HDMI, VGA, and composite video connections, making it easy to connect laptops, DVD players, and other multimedia devices. Additionally, the CP-X445 model features an integrated wireless option, enabling seamless presentation sharing from mobile devices and laptops without the need for cables.

The use of advanced technology is evident in the image quality produced by these projectors. Hitachi's proprietary technology enhances color reproduction and contrast, delivering images that are not only bright but also rich in detail. The projectors also utilize a maintenance-free filter, significantly reducing the need for regular upkeep and prolonging the lifespan of the device.

Portability is an essential characteristic of the CP-X440, CP-X444, and CP-X445 projectors. Their compact design and lightweight construction make them easy to transport, allowing professionals to take them between different venues effortlessly. The projectors also come equipped with a quick-start feature, enabling users to set up and start presentations in no time.

To further enhance usability, these projectors include built-in speakers, providing sufficient audio output for small to medium-sized rooms. The user-friendly interface and remote control make navigation and operation straightforward for users of all skill levels.

In summary, the Hitachi CP-X440, CP-X444, and CP-X445 projectors offer a blend of brightness, resolution, connectivity, and portability, making them ideal choices for various presentation needs. Their advanced features and ease of use ensure that they meet the demands of professionals seeking reliable and effective projection solutions.