Magnavox 32MF338B user manual Initial Setting, 5Initial Setup, Before you begin

Page 14

INITIAL SETTING

These operations are accessible by remote control. Some may also be accessible by controls on the main TV.

5Initial Setup

This section will guide you through the TV’s initial setting which includes selecting a language for your on-screen menu and autoprogram, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure if the TV is connected to antenna or cables.

1After making all the necessary connections, press [POWER y] to turn on the TV.

• This operation may take a few moments.

2Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI iti l Setupt

 

 

 

 

 

 

Select the language for setup display.

English

 

 

 

 

 

 

 

Elija el idioma de ajuste.

Español

 

 

 

 

 

 

 

Sélectionner langue écran config.

 

 

 

Français

 

 

 

 

 

 

Note:

•If you connect the cable system directly, contact the CATV installer.

•If you press [POWER y] or [MENU] during autoprogram, this setting will be canceled.

•The initial autoprogram function can be executed for either “Air” or “Cable” only once. When you change the connection (Air/Cable), set autoprogram again. (Refer to page 15.)

•You can cancel or exit the initial autoprogram menu by pressing [MENU].

•If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the TV, “Helpful Hints” appears. Follow the instructions listed on the TV screen.

No channel is registered.

Press and hold "OK" key on the remote control for 3 seconds.

Contact support hotline provided on manual or back of unit.

Sin canal registrado.

Pulse durante 3 segundos la tecla "OK" en el control remoto.

Llame teléfono de apoyo en manual o atrás de TV.

Pas de chaîne consign.

Enfoncez "OK" 3 secondes sur la télécommande.

Contacter numero d'urgence dans manuel ou arrière appareil.

Select

OK OK

MENU

Exit

•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [OK].

3Use [Cursor K/L] to select “Air” for TV channels or “Cable” for CATV channels, then press [OK].

InitialI iti l Setupt

Make sure the antenna is connected to "ANT.IN" jack. Select your signal source.

Air

CableOr

ANT.IN

Air

Cable

Select

OK OK

BACK

MENU

Back

Exit

•Scanning and memorizing of channels start automatically.

InitialI iti l Setupt

Now the system is scanning for channels, please wait.

2%

Analog channels

0 ch

Digital channels

0 ch

MENU

Exit

•When the scanning and memorizing of channels are completed, the lowest memorized channel will be displayed.

14

EN

A8AF2UH_32MF338 B_EN_v2.indd 14

2008/02/15 14:52:27

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 32MF338B LCD TV Notification For Customer UseIntroduction Read before operating equipmentRADIO-TV Interference When Carrying this TVFCC Warning To Avoid the Hazards of Electrical Shock and Fire5Mounting the TV Stand 5Supplied Accessories5Symbols Used in this Manual DTV/TV/CATV FeaturesContents Battery Precautions 5Buttons on the Remote Control5Installing the Batteries Back5Rear Panel Volume5Control Panel ChannelAntenna Connection Preparation5Basic Connection Connection to Cable Receiver Box or Satellite BoxHDMI-DVI Connection 5External Device ConnectionHdmi Connection Component Video Connection Video ConnectionVideo in Connection Audio Output ConnectionFormat Following signals can be displayedPC Connection Before you begin Initial Setting5Initial Setup Make sure if the TV is connected to antenna or cables5Main Menu Autoprogram5Language Selection Press Menu to exitWatching TV 5Volume AdjustmentTo Cancel the Sleep Timer 5Channel Selection5Switching Audio Mode 5Still Mode5Switching Each Input Mode Press Info 5Screen InformationBroadcasting Information For 43 video signal 5TV Screen Display ModeFor 169 video signal Channel registration list Optional Setting5Channel List 5Add Channels Use Cursor K/L to select Channel List, then press OK5Antenna Confirmation Use Cursor K/L to select Antenna, then press OKUse Cursor s/B to adjust 5Picture AdjustmentAdjust the picture quality Smart PictureYou can adjust treble and bass 5Sound AdjustmentReset Sound Settings Treble, BassCC-1 and T-1 Caption Mode5Closed Caption CC-3 and T-3Use Cursor K/L to select DTV CC, then press OK 5DTV Closed CaptionDTV CC Font Size 5CC StyleFont Style Font Opacity Font ColorEdge Type Back Color5Parental Control Use Cursor K/L to select Parental Control, then press OKUse Cursor K/L to select US Movie ratings lock To Set the Sub RatingsAssociation of America Then press OK Press OKUse Cursor K/L to select Change Pin, then press TV-YAuto Adjustment 5PC SettingsClock, Phase Horizontal Position, Vertical Position5HDMI Audio Use Cursor K/L to select HDMI1 Audio Source, then press OKAll connections once before calling for service Troubleshooting5Troubleshooting Guide May interrupt the remote control signal of this TV Check the batteries of the remote controlRefer to IR Signal Check on CH. / . Refer to Switching Each Input Mode onGlossary MaintenanceInformation With an AM radio5Specifications What is not Covered Exclusions Limitations Warranty CoverageWhat is Covered This Limited Warranty does not cover
Top Page Image Contents