Magnavox 32MF338B Watching TV, 5Channel Selection, 5Volume Adjustment, To Cancel the Sleep Timer

Page 17

WATCHING TV

INTRODUCTION

5Channel Selection

Select channels by pressing [CH. / ] or [the Number buttons].

•To select the memorized channels, use [CH. / ] or [the Number buttons].

•To select the non-memorized channels, use [the Number buttons].

To Use [the Number buttons]

TV

5Volume Adjustment

This section describes how to adjust the volume. The mute function, which turns the sound off and on, is also described.

Use [VOL. / ] to adjust the audio volume.

Volume 20

PREPARATION

- When selecting Analog Channel 12

• The volume bar will be displayed at the bottom of

 

 

 

 

 

the TV screen when adjusting the volume.

 

 

 

 

 

• The volume bar will automatically disappear in a few

 

 

 

 

 

seconds.

DTV

Press [MUTE] to turn off and on the sound.

 

INITIAL SETTING

-When selecting digital channel 12-1

Be sure to press [–]before entering the Minor Channel number.

•Press [PREV CH] to return to the previously viewed channel.

About digital TV broadcasting:

With its high definition broadcast, digital broadcasting far surpasses analog broadcasting in both its picture and sound quality.

What is the minor channel?

By using high compression technology, digital broadcasting offers a service that enables multiple signals to send simultaneously.

Therefore, you can select more than one program per major channel since digital broadcasting technology distinguishes between multiple channels broadcast by a single network.

Mute

•

“Mute” is displayed on the TV screen for a few

WATCHING

 

seconds.

 

TV

Press [MUTE] again or [VOL. / ] to recover the

 

original volume.

 

5Sleep Timer

OPTIONAL

 

 

The sleep timer can be set to automatically turn off the TV after an

SETTING

 

 

 

 

 

 

incremental period of time.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1Press [SLEEP] to set the sleep timer.

 

Sleep

Off

 

TROUBLESHOOTING

• Sleep timer display appears on the TV screen.

 

 

 

 

NTSC (analog mode)

CH4

[Air Time]

18:00

18:30

19:00

19:30

20:00

20:30

ATSC (digital mode)

CH4 No signal No signal

CH4

(high definition TV)

CH4

CH4-1

No signal

CH4

No signal

CH4-2

CH4

CH4-1

CH4-2

2 Press [SLEEP] repeatedly to change the amount of time

 

 

 

until shut off.

 

 

 

INFORMATION

 

 

 

 

Sleep

120min.

 

 

 

 

 

 

 

 

 

 

 

•You can set your TV to turn off after a set period of time (from 30 to 120 minutes).

•Each press of [SLEEP] will increase the time by 30 minutes.

•After setup, the sleep timer display can be called up for checking by pressing [SLEEP].

To Cancel the Sleep Timer

major channel

minor channel

: change automatically

 

 

: change manually by using [CH. /

]

 

 

 

 

Note:

 

 

•“No Signal” will appear on the TV screen after the minor channel broadcast is over.

•“Audio only program“ message will appear on the TV screen, when you receive only sound signal.

Press [SLEEP] repeatedly until “Sleep Off” is displayed on the TV screen.

Note:

•The sleep timer display will automatically disappear in a few seconds.

•When you disconnect the TV from the AC outlet or when a power failure occurs, the sleep timer setting will be canceled.

17

EN

A8AF2UH_32MF338 B_EN_v2.indd 17

2008/02/15 14:52:30

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 32MF338B LCD TV For Customer Use NotificationRead before operating equipment IntroductionFCC Warning When Carrying this TVRADIO-TV Interference To Avoid the Hazards of Electrical Shock and Fire5Mounting the TV Stand 5Supplied Accessories5Symbols Used in this Manual DTV/TV/CATV FeaturesContents 5Installing the Batteries 5Buttons on the Remote ControlBattery Precautions Back5Control Panel Volume5Rear Panel Channel5Basic Connection PreparationAntenna Connection Connection to Cable Receiver Box or Satellite BoxHDMI-DVI Connection 5External Device ConnectionHdmi Connection Video Connection Component Video ConnectionAudio Output Connection Video in ConnectionFormat Following signals can be displayedPC Connection 5Initial Setup Initial SettingBefore you begin Make sure if the TV is connected to antenna or cablesAutoprogram 5Main MenuPress Menu to exit 5Language SelectionTo Cancel the Sleep Timer 5Volume AdjustmentWatching TV 5Channel Selection5Switching Audio Mode 5Still Mode5Switching Each Input Mode Press Info 5Screen InformationBroadcasting Information For 43 video signal 5TV Screen Display ModeFor 169 video signal 5Channel List 5Add Channels Optional SettingChannel registration list Use Cursor K/L to select Channel List, then press OKUse Cursor K/L to select Antenna, then press OK 5Antenna ConfirmationAdjust the picture quality 5Picture AdjustmentUse Cursor s/B to adjust Smart PictureReset Sound Settings 5Sound AdjustmentYou can adjust treble and bass Treble, Bass5Closed Caption Caption ModeCC-1 and T-1 CC-3 and T-3Use Cursor K/L to select DTV CC, then press OK 5DTV Closed CaptionDTV CC Font Size 5CC StyleFont Style Edge Type Font ColorFont Opacity Back ColorUse Cursor K/L to select Parental Control, then press OK 5Parental ControlAssociation of America To Set the Sub RatingsUse Cursor K/L to select US Movie ratings lock Then press OK Press OKTV-Y Use Cursor K/L to select Change Pin, then pressClock, Phase 5PC SettingsAuto Adjustment Horizontal Position, Vertical PositionUse Cursor K/L to select HDMI1 Audio Source, then press OK 5HDMI AudioAll connections once before calling for service Troubleshooting5Troubleshooting Guide Refer to IR Signal Check on Check the batteries of the remote controlMay interrupt the remote control signal of this TV CH. / . Refer to Switching Each Input Mode onInformation MaintenanceGlossary With an AM radio5Specifications What is Covered Warranty CoverageWhat is not Covered Exclusions Limitations This Limited Warranty does not cover
Top Page Image Contents