Magnavox 32MF338B Check the antenna or cable connection to the main TV, Broadcast, Dialogue

Page 35

5FAQ

Question

Answer

 

• Check the antenna or cable connection to the main TV.

 

• Check the batteries of the remote control.

 

• Check if there is an obstacle between the infrared sensor window and

 

the remote control.

 

• Test the signal output. If OK, then possible infrared sensor trouble.

 

(Refer to “IR Signal Check” on page 36.)

My remote control does not work. What

• Aim the remote control directly at the infrared sensor window on the

should I do?

front of the TV.

 

• Reduce the distance to the TV.

 

• Re-insert the batteries with their polarities (+/– signs) as indicated.

 

• When there is an infrared-equipped device such as PC near this TV, it

 

may interrupt the remote control signal of this TV.

 

• Move the infrared-equipped device away from this TV, change the angle

 

of the infrared sensor or turn off the infrared communication function.

How come the Initial setup appears every

• Connect the RF cable to the TV directly and run the initial setup.

time I turn on this TV?

• Make sure to complete the channel scan before turning off the TV.

 

• Make sure autoprogram has been completed.

 

(Refer to “Autoprogram” on page 15.)

 

• Autoprogram must be completed when you set up the TV for the first

 

time or move it to a location where previously unavailable channels are

 

broadcast.

 

• The selected channel may not be broadcasting.

Why I cannot watch some of TV programs?

• When autoprogram is interrupted and not completed, some channels

will not be received. Make sure to complete.

 

 

(Refer to “Autoprogram” on page 15.)

 

• The selected channel cannot be viewed by the Parental control setting.

 

(Refer to “Parental Control” on page 29.)

 

• The TV requires some kind of antenna input. An indoor antenna (rabbit

 

ears), an external antenna, or an RF coaxial cable from your wall or cable

 

receiver /satellite box needs to be plugged into the TV.

How come there is no image from the

• Check if the right input mode is selected by pressing [SOURCE] or using

[CH. / ]. (Refer to “Switching Each Input Mode” on page 18.)

connected external devices?

• Check the antenna or cable connection to the TV.

 

 

 

Whenever I entered channel number,

• Many digital channels have alternate channel numbers. The TV changes

the numbers automatically to the ones signifying the broadcasting

it changes automatically.

stations. These are the numbers used for analog broadcasts.

 

 

 

 

• Captions that are delayed a few seconds behind the actual dialogue are

Why are captions not displayed entirely?

common for live broadcasts. Most captioning production companies can

Or, captions are delayed behind the

display a dialogue to maximum of 220 words per minute. If a dialogue

dialogue.

exceeds that rate, selective editing is used to insure that the captions

 

remain up-to date with the current TV screen dialogue.

How can I set the clock ?

• There is no clock function on this TV.

 

 

INTRODUCTION PREPARATION INITIAL SETTING WATCHING TV OPTIONAL SETTING TROUBLESHOOTING INFORMATION

35

EN

A8AF2UH_32MF338 B_EN_v2.indd 35

2008/02/15 14:53:01

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 32MF338B LCD TV For Customer Use NotificationRead before operating equipment IntroductionTo Avoid the Hazards of Electrical Shock and Fire When Carrying this TVFCC Warning RADIO-TV Interference5Mounting the TV Stand 5Supplied Accessories5Symbols Used in this Manual DTV/TV/CATV FeaturesContents Back 5Buttons on the Remote Control5Installing the Batteries Battery PrecautionsChannel Volume5Control Panel 5Rear PanelConnection to Cable Receiver Box or Satellite Box Preparation5Basic Connection Antenna ConnectionHDMI-DVI Connection 5External Device ConnectionHdmi Connection Video Connection Component Video ConnectionAudio Output Connection Video in ConnectionFormat Following signals can be displayedPC Connection Make sure if the TV is connected to antenna or cables Initial Setting5Initial Setup Before you beginAutoprogram 5Main MenuPress Menu to exit 5Language Selection5Channel Selection 5Volume AdjustmentTo Cancel the Sleep Timer Watching TV5Switching Audio Mode 5Still Mode5Switching Each Input Mode Press Info 5Screen InformationBroadcasting Information For 43 video signal 5TV Screen Display ModeFor 169 video signal Use Cursor K/L to select Channel List, then press OK Optional Setting5Channel List 5Add Channels Channel registration listUse Cursor K/L to select Antenna, then press OK 5Antenna ConfirmationSmart Picture 5Picture AdjustmentAdjust the picture quality Use Cursor s/B to adjustTreble, Bass 5Sound AdjustmentReset Sound Settings You can adjust treble and bassCC-3 and T-3 Caption Mode5Closed Caption CC-1 and T-1Use Cursor K/L to select DTV CC, then press OK 5DTV Closed CaptionDTV CC Font Size 5CC StyleFont Style Back Color Font ColorEdge Type Font OpacityUse Cursor K/L to select Parental Control, then press OK 5Parental ControlThen press OK Press OK To Set the Sub RatingsAssociation of America Use Cursor K/L to select US Movie ratings lockTV-Y Use Cursor K/L to select Change Pin, then pressHorizontal Position, Vertical Position 5PC SettingsClock, Phase Auto AdjustmentUse Cursor K/L to select HDMI1 Audio Source, then press OK 5HDMI AudioAll connections once before calling for service Troubleshooting5Troubleshooting Guide CH. / . Refer to Switching Each Input Mode on Check the batteries of the remote controlRefer to IR Signal Check on May interrupt the remote control signal of this TVWith an AM radio MaintenanceInformation Glossary5Specifications This Limited Warranty does not cover Warranty CoverageWhat is Covered What is not Covered Exclusions Limitations
Top Page Image Contents