Fujitsu P42XHA58E Series, P50XHA58E Series user manual Information, Checking Accessories

Page 2

INFORMATION

•Receptacle

Make sure that the power cord’s grounding wire is grounded.

The plasma display comes with a 3-prong power plug; one prong is connected to the grounding wire. If you have only a 2-hole receptacle, you will need to have it replaced. Contact your dealer for more information.

•Have the plasma display inspected and cleaned by your dealer at regular intervals.

•Do not display the same picture for a long time, because part of the screen may “burn-in” and create a residual image if the same picture is displayed for an extended period of time. To prolong the life of the plasma display, we recommend the use of the “Screen Orbiter” settings. (See P. E-25) When a residual image was created, reduce the residual image by using the “White screen” settings. Note that there may also be cases when it can not be recovered completely. (See P. E-26)

•When the screen size is set to “Normal” and a picture was displayed for a long time, a residual image may be created at the boundary with the part at which an image is not displayed. We recommend that you use a screen size other than “Normal”. (See P. E-12)

•High-precision technology has been used in the manufacture of the plasma display panel, in which the effective pixels exceeds 99.99%. However, please be aware, that fewer than 0.01% of the pixels may be missing or remain constantly lit.

•Some models are fitted with a radiator fan to prevent the plasma display’s internal temperature from rising during operation. Be careful of the air emitted by the radiator fan, as it may be hot.

•Contact your dealer when causing a bad influence to the plasma display and other audio-visual equipment mutually.

You may need to move your plasma display if it produces degraded pictures or noise due to electromagnetic radiation, or if the infrared remote control does not function properly.

•Pictures may not be displayed properly if you connect a non-standard PC to the RGB input terminal. In this case, contact your dealer for more information.

•The protective circuit, built into the display, automatically turns off the power if the display has a problem. In this case, you will see that the power indicator lamp flashes red or green.

Warning

If the power indicator lamp flashes red or green, this signifies that the display has developed a problem. When this happens, be sure to unplug from the receptacle to prevent fire or electric shock. Then contact your dealer.

•It is important to install the plasma display in a location close to a receptacle, and where the emergency stop button can be easily reached.

CHECKING ACCESSORIES

User’s Manual

Safety Precautions

Remote control

AA battery (2)

Power cord

Manual

Manual

Small ferrite core (2)

Large ferrite core (2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No.:ZCAT1518-0730

No.:SFT-72SN

Mfr.:TDK

Mfr.:TKK

Note

•Cables for connecting the display to external equipment are not supplied. Contact your dealer for more information on these products.

•In order to facilitate the explanations, pictures and diagrams in this manual may differ slightly from the actual items.

E-2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents USER’S Manual Checking Accessories InformationInstallation Attaching the Ferrite CoresDisplay Section Back Part Names and FunctionsDisplay Section Front Display Section Bottom Description of Input Terminals Pin No Input signalPin No Signal Trademark InfomationUsing the Remote Control Remote ControlEffective Range for the Remote Control Putting Batteries in the Remote ControlPrecautions Display front Display sideDisplay bottom DVD RECORDER/PLAYER, Satellite TunerVCR/PC Video Input Mode Turning the Power on and STAND-BYAdjusting the Volume Basic OperationsPicture Mode RGB Input ModePress to select the input mode Convenient FunctionsPress  Switching Between Screen SizesWatching Pictures on the Wide Screen SizeScreen Size Aspect RatioAdjustment Menu MenuBasic Procedures of Adjustment Menu Adjusting the Picture Setting the Picture Memory Setting the Picture ModePrecision Setting Precision Setting Setting the Color Focus Adjusting the Color TempSetting the User Color Temp Making the Progressive Scan Settings Adjusting Screen Size Size Adjusting Screen Position and SizeAdjusting Screen Position Position Adjusting Bass Bass Adjusting AudioAdjusting Treble Treble Adjusting Volume Balance BalanceSetting Display Information OSD Other AdjustmentsAdjustment On Screen MenuSelecting the settings of D-SUB Input terminal Setting the Input TerminalsSelecting the settings of Video/S-video Input terminal Selection of indications Name SelectSelecting input terminals Audio Input Other SettingsAuto Off-NO SIG Minimizing phosphor burn-in Screen OrbiterDisplaying white over entire screen White Screen Setting RGB Input Signal Compulsorily Direct Settingfor RGBSpecifying RGB Input Signal Code Setting Minimizing phosphor burn-in BackgroundPress Cor Dto select the Yes Initialization of User Adjustment ValuePress Eor Fto select Factory Options Main Supported Signals Frequency kHz Frequency HzProduct Name P42XHA58EBb P50XHA58EBb SpecificationsModel Series Name RegulationProblem Action Cleaning and MaintenanceBefore Obtaining Service
Top Page Image Contents