Fujitsu P42XHA58E Series, P50XHA58E Series user manual Other Settings, Auto Off-NO SIG

Page 25

OTHER SETTINGS

English

Auto Off-NO SIG.

You can make to the standby state automatically when the no signal state continued during set up time. Press CDto select the “Time”.

Press EFto select the amount of time before the standby state starts.

Off 1 min. 15 min. 45 min. 60 min. 

Press <to store.

* The numerical value is the approximate amount of time before the standby state starts.

You can assign the black or white color for the background color at the no signal state. Press CDto select the “Background”.

Press EFto select the displayed background displayed.

Black White

“Auto Off-NO SIG.” selection screen

Français Español Deutsch

Press <to store.

* The background color changes to assigned color state after approximate 20 seconds at the no signal state.

Selecting input terminals (Audio Input)

You can use this option to select the available terminals to receive the audio from input equipment.

(1)Select “Audio Input” and press <.

The “Audio Input” selection screen will appear.

(2)Press Cor Dto select video input terminal.

(3)Select a related audio input terminal.

Each time you press Eor F, one of the available choices appears in the following sequence:

No Audio Audio 1 Audio 2 • • • • • 

[No Audio]: No audio in the corresponding mode.

“Audio Input” setting screen

 

[Audio 1-3]: Selects Audio 1 through 3 for receiving audio in the corresponding mode.

[Audio 4-5]: HDMI

 

* There is also “Audio Input” that cannot be selected.

 

* Repeat steps (2) and (3) for each piece of input equipment.

 

(4) Press <to store.

 

* AUDIO menu will not be displayed when “No Audio” is selected.

 

Minimizing phosphor burn-in (Screen Orbiter)

for RGB

You can use this option to move the screen position to minimize phosphor-induced “burn-in”.

 

Follow the steps below.

 

 

(1)

Select “Screen Orbiter” and press <.

 

 

The “Screen Orbiter” setting screen will appear.

 

(2)

Press Cor Dto select “Mode/Time”.

 

(3)

Select a desired pattern.

 

 

Each time you press Eor F, one of the available choices appears in the following sequence:

 

 

Off

Time

Mode

“Screen Orbiter” setting screen

 

[Off]:

Disables Screen Orbiter.

 

 

[Time]:

Moves the pattern approximately every one hour.

 

 

[Mode]:

Moves the pattern when the power is turned ON or when you switch between modes.

 

Póññêèé Português Italiano

中文

日 本 語

E-25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents USER’S Manual Information Checking AccessoriesAttaching the Ferrite Cores InstallationDisplay Section Front Part Names and FunctionsDisplay Section Back Display Section Bottom Pin No Signal Pin No Input signalDescription of Input Terminals Trademark InfomationRemote Control Using the Remote ControlPrecautions Putting Batteries in the Remote ControlEffective Range for the Remote Control Display front Display sideVCR/PC DVD RECORDER/PLAYER, Satellite TunerDisplay bottom Adjusting the Volume Turning the Power on and STAND-BYVideo Input Mode Basic OperationsPress to select the input mode RGB Input ModePicture Mode Convenient FunctionsWatching Pictures on the Wide Screen Switching Between Screen SizesPress  SizeAspect Ratio Screen SizeMenu Adjustment MenuBasic Procedures of Adjustment Menu Adjusting the Picture Precision Setting Setting the Picture ModeSetting the Picture Memory Precision Setting Setting the User Color Temp Adjusting the Color TempSetting the Color Focus Making the Progressive Scan Settings Adjusting Screen Position Position Adjusting Screen Position and SizeAdjusting Screen Size Size Adjusting Treble Treble Adjusting AudioAdjusting Bass Bass Adjusting Volume Balance BalanceAdjustment Other AdjustmentsSetting Display Information OSD On Screen MenuSelecting the settings of Video/S-video Input terminal Setting the Input TerminalsSelecting the settings of D-SUB Input terminal Selection of indications Name SelectAuto Off-NO SIG Other SettingsSelecting input terminals Audio Input Minimizing phosphor burn-in Screen OrbiterSpecifying RGB Input Signal Code Setting Setting RGB Input Signal Compulsorily Direct Settingfor RGBDisplaying white over entire screen White Screen Minimizing phosphor burn-in BackgroundPress Eor Fto select Factory Initialization of User Adjustment ValuePress Cor Dto select the Yes Options Frequency kHz Frequency Hz Main Supported SignalsModel Series Name SpecificationsProduct Name P42XHA58EBb P50XHA58EBb RegulationBefore Obtaining Service Cleaning and MaintenanceProblem Action
Top Page Image Contents