Vidikron VP-5000 PlasmaView, Auto Function becomes active again, Option Installer Adjust Mode

Page 53

Operation

Auto Function: The PlasmaView can automatically switch to Input 1 when an image signal is detected at that input. To enable this feature, select Auto Function from the Option menu and set it to INPUT 1.

After Auto Function triggers an input switch, when the Input 1 signal is no longer present, the input source reverts to the previously-selected input.

The input signal must be RGB with composite or separate sync; Auto

Note

Function will not work with sync-on-green RGB or component signals.

 

 

When Auto Function is active, selecting an input manually causes Auto

 

Function to be temporarily disabled. If you cycle power to the

 

PlasmaView, Auto Function becomes active again.

Screen Maint.: When in Installer Adjust mode, select Screen Maint. from the Option menu to program the screen maintenance features of the PlasmaView to operate at regular intervals. This is useful for preventing image burn-in.

You can program the PlasmaView to switch inputs and/or replace the normal source signal with a white field, an inverse image or an “orbiting” image. You can specify a time of day and day of the week when you want this to take place.

To set up a screen maintenance program:

1.Press SET to select the DATE field for the first program. Press or to select one of the following:

•SUN, MON, TUE, WED, THU, FRI or SAT for a program that runs once only on the next occurrence of that day.

•* for a program that runs daily.

•*SUN, *MON, *TUE, *WED, *THU, *FRI or *SAT for a program that runs weekly on that day.

2.Press SET, then followed by SET again to set the program start time.

3.Press or to set the hour component of the start time.

4.Press , then or to set the minute component of the start time.

5.Press SET, then followed by SET again to set the program end time (repeat steps 3 and 4).

6.Press SET, then followed by SET again to specify an input associated with this program. Choose “–” to specify the input that was active when the PlasmaView was last powered off.

7.Press SET, then followed by SET again to select the PATTERN field for this program. Press or to select one of the following:

•Choose “–” to specify the function that was active when the PlasmaView was last powered off.

•Choose WHITE to display a white field.

•Choose INVERSE to display an inverse image.

•Choose ORBITER to display an “orbiting” image.

8.Press SET.

9.Repeat steps 1 through 8 as desired to create additional screen maintenance programs.

Option (Installer Adjust Mode)

INSTALLER ADJ.

 

 

 

INPUT 3

PICTURE SCREEN

SET-UP

OPTION

SCREEN MAINT.

 

 

 

TEST PATTERN

: OFF

SIDEBAR ADJ.

 

 

 

BAUD RATE

: 9600BPS

ID NUMBER

: 01H

SET SET

MENU

EXIT

SCREEN MAINT.

DATE

ON

OFF

INPUT

PTRN.

*

10:00

– –:– –

–

–

*

20:00

– –:– –

–

WHITE

*

– –:– –

21:00

–

–

–

– –:– –

– –:– –

–

–

–

– –:– –

– –:– –

–

–

–

– –:– –

– –:– –

–

–

–

– –:– –

– –:– –

–

–

RETURN

 

 

 

 

SEL.

SET ADJ.

 

MENU EXIT

Vidikron PlasmaView Owner’s Operating Manual

43

Page 52 Page 54
Image 53
Page 52 Page 54
Contents High Definition Plasma Displays Page Three Year Limited Warranty RIGHTS, Limits and Exclusions Vidikron DOC Compliance Notice Safety Precautions1Table of Contents Specifications Maintenance and TroubleshootingOperation Serial Communications1List of Figures Audio Output Connection Connecting SpeakersList of Figures About This Manual 1IntroductionInformation about obtaining service Using This ManualThey also provide supplemental information Performance or cause a malfunctionKey Features and Benefits Description, Features and BenefitsIntroduction PlasmaView at a Glance Controls and Indicators2Controls and Functions Left / VOL and Right / VOL + Handles at the rear of the panelINPUT/UP PlasmaView Model VP-4200 Connector Panel PlasmaView Model VP-5000 Connector Panel Audio Input 1 3.5-mm stereo mini jack Audio Output 3.5-mm stereo mini jackAudio Input 2 3.5-mm stereo mini jack Analog RGB OUT Input 1 15-pin D-SubPlasmaView Remote Control PlasmaView Remote ControlVolume + Installer Adjust pin holeDirectional Buttons OFF pin holeControls and Functions Remote Control 3InstallationOperation Approx 23 ft 7mInstallation Step Procedure For Details, refer to Quick SetupDisplay properties ThroughHigh-Altitude Operation Installation ConsiderationsVentilation Requirements for Enclosure Mounting VentilationInstallation RGB/Component Video Input 1 Connection Connections to the PlasmaViewAnalog RGB OUT Input 1 Connection Composite or S-Video Input 3 Connection Component Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables 11. Audio Output Connection 13. RS-232 Control System Connection ConnectionInstallation Changing the OSD Language Turning on the Power4Operation Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal InformationChanging the Aspect Ratio Description PIX by PIX Using the On-Screen Menus Screen PictureSet-Up OptionMain Menu Picture Perform the adjustments in the order listed hereTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness To highlight Image Position ScreenPower Turning the picture PowerIndicator Set-UpDVI Setup Option Language Refer to Changing the OSD Language onType 3 causes the image to move one pixel at a time PlasmaView, Auto Function becomes active again Option Installer Adjust ModeFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Picture OrientationTo use PIP, press the Split button Using Picture-In-Picture PIPPress the Swap button to replace the main screen with Sub-screen or vice versa. This switches the audioWindows Viewing an Enlarged Area of the Display Enlarging One Part of the ScreenOperation Cleaning 5Maintenance and TroubleshootingTroubleshooting Tips Cleaning the ScreenThermal Alert OUT of Range Signal NGShut Down FAN FailureArgument 3 bytes Serial Command Syntax6Serial Communications Minimum Command Value Range DescriptionVideo Minimum MaximumAudio MSTS02MSTS10 MSTS08MSTS09 Functional Lock SET-UP Menu CommandsVideo Average Option Menu CommandsPicture Menu Commands Installer Adjust Mode Option Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeSET-UP Menu Commands Installer Adjust Mode Contrast MonotoneInput 1... Input DW1 Minimum Maximum Adjustment Commands7Specifications Delivery to the end user Specifications are subject to change without noticeEnd user except for plasma glass panel PlasmaView Dimensions 25.00 14.00 48.41 49.98 13.98 Specifications Horiz Computer/Video Signal CompatibilityInput Refresh Rate 1152x870 Specifications Page RUMA-009815 Rev -07-07

VP-5000a, VP-5000, VP-4200, VP-6000, VP-6000a specifications

Vidikron, a company known for its commitment to high-quality video solutions, has produced several projectors that cater to different needs and preferences in the realm of home theater systems. The VP-4200A, VP-6000A, VP-6000, VP-4200, and VP-5000 are notable models that incorporate advanced technologies and features designed to deliver exceptional viewing experiences.

The Vidikron VP-4200A is recognized for its impressive brightness and color accuracy. It supports resolutions up to 1080p, making it ideal for high-definition content. One of its standout features is the use of DLP technology, which provides sharp images and vibrant colors, ensuring that viewers experience rich visual depth. The VP-4200A also incorporates a user-friendly interface, allowing for easy adjustments and customization to suit individual preferences.

Moving to the VP-6000A, this model takes performance a step further with enhanced contrast ratios and superior black levels. It is designed for larger viewing environments, capable of producing larger images without compromising quality. The VP-6000A uses advanced image processing technologies, which help to improve picture quality, especially in fast-moving scenes, making it a favorite among action movie aficionados.

The VP-6000 offers similar specifications to the VP-6000A but tends to be slightly more affordable. It still boasts impressive features, including an array of input options such as HDMI and component video, ensuring compatibility with various devices. The strong build quality and reliability of the VP-6000 make it a compelling choice for users looking for durability and performance.

The VP-4200 provides a balance between price and performance, offering excellent image quality while remaining budget-friendly. This model is perfect for users who desire a home theater experience without the high-end price tag. With customizable settings, users can tailor their viewing experience to match their specific needs.

Lastly, the Vidikron VP-5000 stands out with its integration of the latest in video processing technologies. This model supports 4K content, making it a future-proof option as more media becomes available in higher resolution formats. Additionally, the VP-5000's sleek design and advanced connectivity features make it an attractive addition to any home theater setup.

Together, these models represent Vidikron's dedication to delivering high-performance video projectors tailored to various user needs, ensuring that everyone can enjoy a premium viewing experience in the comfort of their homes.
Top Page Image Contents